-
Product
NI Vehicle Radar Test System
-
VRTS provides automated radar measurement and obstacle simulation capabilities for 76 to 81 GHz automotive radar systems. With VRTS, you can perform precision RF measurements and simulate a wide range of test scenarios for radar hardware and software subsystems, including sensors, advanced driver assistance systems (ADAS), and embedded software. Use VRTS for all phases, from design to manufacturing, of ADAS and radar system test.
-
Product
SMD Array Type LCR Test Fixture
16034H
-
The 16034H is designed for impedance evaluations of array-type SMD.The minimum SMD size that this fixture is adapted to evaluate is 1.6(L)x0.8(W)[mm]. Since the tip of the measurement electrodes are very thin and the device holder is extremely flat, the device can be shifted and the measurement electrodes can contact each of the elements of the array-type component.
-
Product
SSD Test Systems
-
Enables Rapid SSD Development and Production Ramp with Flexible Test Solution In the high-growth and highly competitive SSD market, a test system that supports multiple protocols can eliminate the need for retooling and achieve faster transitions from one product version — or one product generation — to the next. Advantest SSD Test System allows manufacturers to rapidly grow their product portfolios while remaining adaptable to the many changing needs of the evolving SSD market. This tester improves users’ engineering efficiency with powerful, easy-to-use software tools and a revolutionary multi-protocol hardware architecture, enabling accelerated SSD product development and a faster time-to-manufacturing ramp.
-
Product
Safety Testing
-
Mobile Power Solutions specializes in guiding your company through today’s increasing quagmire of battery-related safety regulations. MPS provides comprehensive regulatory compliance, safety, and performance testing; we are ANAB accredited to ISO/IEC 17025:2017.
-
Product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
-
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
Product
Ethernet and Fibre Channel Test Platform
SierraNet M1288
-
The SierraNet M1288 Ethernet and Fibre Channel test platform provides best in class analysis, jamming and generation for traffic capture and manipulation for testing application and link characteristics. SierraNet M1288 is the latest in the line of industry leading test and measurement tools from Teledyne LeCroy, designed for today’s high-speed storage and communications fabrics. SierraNet M1288 supports examination and modification of Ethernet and Fibre Channel links utilizing both Pulse Amplitude Modulation 4 (PAM4) and legacy Non-Return to Zero (NRZ) technologies.
-
Product
Semiconductor Test Software
-
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
Product
Safety Tools Testing
-
Weshine Electric Manufacturing Co., Ltd
1. The high voltage is extremely spherical and the grounding voltage is annular.2. The grounding electrode is fixed and the high voltage electrode can be electrically driven to move to the left and right.
-
Product
Product Safety Testing & Certification
-
F2 Labs is a top, full-service product testing company. Our safety laboratory is set up to test/evaluate products for the United States, Canada, Europe, and International Certifications. Our safety facilities are A2LA Accredited, and our safety test data and evaluations are accepted by an OSHA accredited Nationally Recognized Test Lab (NRTL). Our experienced team of engineers can develop an efficient plan for addressing your product’s safety and work with you at our facility or yours to complete the product safety testing and certification.
-
Product
Dielectric Test Fixture
16451B
-
The 16451B is used to evaluate the dielectric constant of solid dielectric materials accurately, and complies with ASTM D150. The 16451B employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixture.
-
Product
CATR Benchtop Antenna Test System
ATS800B
-
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique benchtop CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
Product
Memory Test System
T5221
-
The T5521 is a memory test system that supports wafer test and wafer burn-in test of non-volatile memory devices such as NAND flash, housed within a multi-wafer prober to reduce test floor footprint.
-
Product
Benchtop Communication Test System
ATS3000A
-
The ATS3000A is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23 instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000A also includes the sophisticated IF and baseband I/Q Digital Signal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easy-touse graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets areavailable for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
Product
Liquid Test Fixture
16452A
-
The 16452A provides accurate dielectric constant and impedance measurements of liquid materials. The 16452A employs the parallel plate method, which sandwiches the liquid material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixure.
-
-
Product
Test System
UltraFLEX
-
The UltraFLEX test system delivers the power and precision you need for complex SoC devices built for mobile applications, networking, storage or high-end processing. Choose UltraFLEX when your device mix and throughput goals demand the highest speed, precision, coverage and site count.
-
Product
Imperial Test Executive
ITE
-
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
Product
Product Safety Testing & Certification
-
MET has been certifying, listing, and labeling products for electrical product safety for more than 40 years. In that time, MET has certified thousands of products for compliance to electrical safety standards. This translates into literally millions of products sold in the U.S. and Canada labeled with the MET Mark.
-
Product
110 GHz, 1.0 Mm (m-f) Test Port Cable 10 Cm
11500JK10
-
Connect test ports to devices, fixtures, or probe tips with this 10-cm cable
-
Product
Test Port Adapter Set, 2.4 Mm To 2.4 Mm
85130G
-
The Keysight 85130G test port adapter protects the test set port from connecting directly with the device under test. It has a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a NMD-2.4 mm (f) to NMD-2.4 mm (m) adapter and a NMD-2.4 mm (f) to PSC-2.4 mm (f) adapter. The frequency range for these adapters is dc to 50 GHz with a return loss of 23 dB or better.
-
Product
Product Safety Testing
-
D.L.S. Electronic Systems, Inc
D.L.S. Conformity Assessment is a fully staffed and accredited product safety testing and consulting organization within the D.L.S. corporate umbrella. The Conformity Assessment group offers full compliance testing services for North America, Europe, Pacific Rim, and other global regions including testing to these standards:
-
Product
Electronics Testing Solutions
-
Don’t cut corners when it comes to developing high-quality electronics functional testing solutions. Ball Systems helps you ensure you deliver the quality your customers expect by providing open and reliable advanced technical testing solutions.
-
Product
Safety Chamber, Hydrostatic Test
9901HTX-36x36x15
-
The 3 ft wide by 3 ft deep Hydrostatic Test Safety Chamber, when combined with one of our pump systems, provides a complete hydrostatic test system for testing hose and assemblies or other components requiring pressure testing.
-
Product
Test Handler
M6242
-
Optimal Test Handler for Mass-Production DRAM, with Double the Throughput.
-
Product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
-
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
Product
Test Port Cable, 1 Mm
11500K
-
Connect test ports to devices, fixtures, or probe tips with this 20-cm cable featuring a return loss of 16 dB minimum
-
Product
Safety Tester
-
Safety analyzer is mainly used to provide the test solution for electric car, grid, photovoltaic, electrical appliances, information equipment, medical equipment industry as well as innovative solutions for the various electrical measurement.
-
Product
EBIRST 78-pin D-type To 68-pin Male SCSI Adapter
93-006-401
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Safety
-
Chroma Systems Solutions, Inc.
The purpose of safety testing medical electronic equipment is to be sure that a device is safe from electrical hazards to the patient and caregivers. There are a number of UL, European and Canadian standards that serve as the ruling body on how medical products will be tested, one in particular, IEC60601 (the International Electrical Safety Standard for medical electronic equipment) is experiencing “global harmonization,” meaning it has been accepted and implemented around the world. The IEC60601 standard is mainly intended for product development where safety considerations must be taken into account early in the design phase of a product, however much of it is applied to production line testing since it is the only way for a manufacturer to be sure they are shipping safe product.
-
Product
Bottom Electrode SMD Test Fixture
16197A
-
The 16197A is designed for impedance evaluations of bottom electrode SMDs. It achieves stable frequency characteristics up to 3 GHz and provides highly repeatable measurements. The Keysight 16197A supports various SMD sizes, as small as 1005 (mm)/0402 (inch) and as large as 3225 (mm)/1210 (inch). Accommodation of the 0603 (mm)/0201 (inch) size is available with option 001.
