-
Product
Load Cell Transmitter
MODEL SST-HV
-
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
Load Banks
-
Power Test Dynamometer offers a complete high capacity load testing solution with our load bank and gen set testing systems. Capable of testing generators and AC/DC power sources, our load bank systems safely apply electrical loads across the entire spectrum of operation. By offering a one-stop-shop for your Load Bank and it's accompanying data acquisition software, Power Test is committed to Making Your Testing Easy.
-
Product
Axle Load Simulators
-
In case vehicles need to perform a brake test in laden condition, one could consider to use a load simulator. In that case the vehicles can come to the brake test unladen; the load simulator will add the required load to the axles.
-
Product
50 Ohm BNC to SMA Adaptor Assembly
40-978-511-0.25m
-
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
RF Connectors
AMC Connectors
-
The AMC (Amphenol Micro Coaxial) connector series is a low profile (2.5 mm height off the board) series with an extremely small board footprint (3mm x 3mm).
-
Product
Load Cell Tester
-
Xiamen Elane Electronics Company, Ltd
Large six-digit LED display < Easy to use and small in size < Accuracy of 0.005%FS/10ppm < 2 channels CH0 : -12mV/V~+12mV/V, with resolution 0.1uV/V CH1 : -1.6mV/V~+4.8mV/V, with resolution 0.01uV/V < Four user selectable output units (N, kgf, lbf and mv/V) < Peak Hold function to capture and holding the peak value for the immediate or later reference < Clear key to clear the peak value < Presence of tare key and foot switch to zero the display (tare function) < Great for monitoring and testing load cell characteristics (repeatability, linearity, creeping, temperature drift, etc
-
-
Product
Canister Load Cell
-
Futek Advanced Sensor Technology, Inc.
FUTEK provides a wide range of Canister Load Cells designed for high capacity compression applications. These models offer robust construction with a capacity range beginning
-
Product
RF Adapters
SMB Adapters
-
The SMB adapter allows connection to the SMB server to perform all the common CRUD (Create, Read, Update, and Delete) based operations for files and directories.
-
Product
DC Electronic Loads
-
An adjustable electronic load gives the test engineer the ability to qualify designs, check production batches or service and repair electrical products. Many applications demand an adjustable electronic load. These include the burn-in of new devices along with general power supply, battery, fuel cell and generator testing.Both static and fully dynamic DC loads are offered. With dynamic functionality 2 levels of load current can be set. The rise and fall time can then be adjusted together with the time period spent at each level. The load can also be made to follow complex waveforms by tracking an external arbitrary oscillator input.
-
Product
Loading Rheostats (Resistive Load)
-
Supreme Instrument Laboratories
Loading Rheostat is a device specially designed to meet the requirements of Engineering Laboratories, Electrical Test Rooms and Industries. It is used for loading transformers, power generators, supply mains etc. neatly and efficiently. It can also be used advantageously for regulating current and adjusting voltage besides its application for calibrating meters and thus eliminating the need for graded rheostats.
-
Product
Load Cells
-
For use in harsh environments, our Models T66 (bending beam),T85 and T85-T(shear beams)are manufactured fromstainless steel, fully welded and hermetically sealed to provide total environmental protection (IP68 and IP69K). The T85-Tmodel has a blind loading hole, ideal for use in platform scales.
-
Product
75 Ohm BNC to MCX Adaptor Assembly
40-978-781-0.1m
-
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
RF Adapters
TNC Adapters
-
Amphenol RF offers a wide array of both in-series and between-series TNC adapters in straight and right-angle configurations. 50-ohm and 75-ohm impedance TNC adapters are available with and without panel mounting features. Popular mounting features in bulkhead, both front and rear mount, and 4-hole flange designs. 50-ohm TNC connectors have a frequency range from DC to 11 GHz. 75-ohm TNC connectors have a maximum frequency of 3 GHz.
-
Product
Load Testing
OctoPerf
-
Use auto-correlations rules and frameworks as well as test validation to quickly create virtual users.
-
Product
Digital Load Calibrator
HS 2000
-
Jinan Testing Equipment IE Corporation
The load cell calibrator is used to calibrate the load of testing machine and hardness tester, and also can be used for force measuring. It is digital display type with high accuracy of less than +0.3%, and easy to operate
-
Product
RF Switch
DSM8-0-13000-1082
-
Switch Matrix, DC~13000MHz, 32*8, RJ-45, Reflective, 20ms, SMA Female, 220V
-
Product
Electronic Loads
SLD DC
-
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
-
Product
Mini Load Column Load Cell Compression Only with Mounting
MLC SERIES
-
The MLC Series is our miniature high capacity compression only load cell/force sensor, featuring low profile compact size for a wide range of portable and dedicated applications up to 30,000 lb The load diameter is slightly convex for accurate load distribution. Low deflection through design results in ultra fast frequency response. The MLCs are designed to be mounted in a shallow machined flat pocket or smooth flat surface, either free or fastened via a bottom 6-32 tapped hole. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial Environments.
-
-
Product
RF Over Fiber
-
Quintech Electronics and Communications Inc.
Transmit and Receive Fiber Optic Signals.
-
Product
Thermal Load Boards
-
Thermal Engineering Associates, Inc.
A Thermal Load Board (TLB) is used to simulate an application printed circuit assembly (PCA) either before all the heat-producing components are available for mounting on the application PCA or if the heat-producing components require complex electronic circuitry to create heat within the components. The TLB is typically designed to be as mechanically and thermally equivalent to the application PCA and usually offers a way to vary the power dissipation of the elements that simulate the heat-producing components.
-
Product
DC Electronic Load
3310F Series
-
Each 3310F Series module has its own control and display panel, CC/CR/CV/CP/Dynamic modes, plug in 3300F with 150 sets Store/Recall memory which provides load set-up more efficiently，also can be controlled intranet via RS232、Ethernet、USB and GPIB interface.
-
Product
RF Communication Module
RF-200
-
The RF Communication module allows remote operation of asingle sensor or a chain of sensors. The remote single sensoror chain is connected to an RF Communication module and to aBattery Module which powers them all.
-
Product
AC Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
We offer AC load banks in a variety of capacities and any voltage combination, with custom models including resistive, inductive, capacitive or resistive/reactive combination loads, all tailored to meet any load testing requirement.
-
Product
AC Load Bank
XL750-XL800 Series
-
Mosebach Manufacturing Company
The XL750-XL800 Series load banks offer you a continuous load at various voltages in a compact, lightweight enclosure.
-
Product
RF Adapters
SMA Adapters
-
Are semi-precision coaxial RF connectors developed in the 1960s as a minimal connector interface for coaxial cable with a screw-type coupling mechanism.
-
Product
Load Tests
-
For the production and quality assurance of electric motors and electric drive systems, the use of flexible and customer-specific testing technology is required. Vogelsang & Benning supplies the same to the needs and the application of the customer.
-
Product
RF Power Meter
PMX40
-
The PMX40 provides design engineers and technicians the utility of traditional benchtop instrument, the flexibility and performance of modern USB RF power sensors, and the simplicity of a multi-touch display built with Boonton award-winning technology.
-
Product
JD Edwards Load Testing
Dimension LoadTest
-
Dimension LoadTest™ is a powerful yet easy to use load testing tool for JD Edwards EnterpriseOne applications. DWS have designed Dimension LoadTest such that any experienced System Administrator/CNC should be able to setup, create, run and monitor load tests to effectively stress test JD Edwards EnterpriseOne applications.
