-
Product
Current Transformer
ST-9RCT
-
Standard Electric Works Co., Ltd
● Primary Current Rating (Amp) : 800~2000
-
Product
SAFETY TESTERS ( CURRENT LEAKAGE TESTERS )
ST-05
-
Safety Tester Model ST-05 is a test set for testing small equipment powered by 120V 60 Hz, from an approved U-ground source. Test also can be run on double-insulated tools an on appliances with two-pin parallel plugs.
-
Product
Constant Current System
CCS-BTA
-
Vernier Software & Technology, LLC
The Constant Current System is a DC power source with a built-in current probe designed for use in electrochemistry experiments.
-
Product
AC Clamp Meter
CM3289
-
Use in even more applications with an optional flexible sensor. Measure both wires in confined spaces and thick wires with a single instrument.
-
Product
Rogowski AC Current Probe, 23 MHz, 3000 A
N7040A
-
The Keysight N7040A Rogowski coil current probe is designed for measuring AC currents up to 3,000 A with the bandwidth ranging from 3 Hz to 23 MHz. The probe is easy to use because it has a thin, lightweight, flexible and simple-to-use clip-around Rogowski coil that enables current measurement in the most difficult to reach parts and confined spaces of a circuit under test. It can also measure large AC current without increase in transducer size.
-
Product
Current Transformer
ST-6RCT
-
Standard Electric Works Co., Ltd
● Primary Current Rating (Amp) : 400~600
-
Product
Universal Clamp Tester
M-310
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
The unique U type CT enabled to measure the load current of single or three phase cable without separating the cable to the wires. Leakage current measurements with least affection from the external magnetic field. Wide current measurements.(AC0.01mA-300A)
-
Product
AC & DC Analog Leakage Meters
1807 TB
-
Standard Electric Works Co., Ltd
● AC Voltage Input/output range： 100~240 Vac● Frequency： 50~60Hz● Current： 10A
-
Product
Earth Ground Clamp Meter
T2000
-
T2000 is a professional clamps specially developed to evaluate resistance of earth rods with no need to disconnect any part of the system (STAKELESS METHOD)
-
Product
Digital Clamp Tester (CE)
M-2100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Wide current measurements with tear drop type 55mmφCT up to 2000A.*Data-hold and Auto power off function.*Additional AC/DC voltage, resistance, diode test, continuity check.*Conform to IEC safety requirements.
-
Product
Flexible Clamp Meter 18 inch
FLIR CM57
-
The FLIR CM57 is an ergonomic tool designed to simplify difficult current measurements. Made with a narrow, 18-inch (45.72 cm) flexible coil clamp, the CM57 lets you easily take measurements in tight or awkward spots. It is ideal for multiple-conductor measurements and double-wrap requirements. With Bluetooth® communication for remote viewing and data transfer to iOS® and Android™ devices via the FLIR Tools Mobile app, you can analyze and share data fast right from the jobsite.
-
Product
Standard - 1.44 (41.00) - 4.50 (128.00) High Current Probe
HCP-13A
-
Current Rating (Amps): 15Average Probe Resistance (mOhm): 25Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 250,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Current Probe For Non-Intrusive Measurement Of AC, DC, And Waveform Currents
CP 305
-
The CP 305 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.Using advanced Hall Effect technology the CP 305 can measure currents accurately up to 450A peak over the frequency range of DC to 20 kHz.
-
Product
Universal Clamp Tester
M-200
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
The unique U type CT enabled to measure the load current of single or three phase cable without separating the cable to the wires.33mmφCT window and ultra compact size.Data-hold function. Especially useful when working in dark or hard to get areas.
-
Product
Current logger0 to 20mA
TK-4802
-
Supplied with an input cable, this logger can measure current between 0 and 20mA DC and can be connected to many industry standard devices, such as CO2 sensors and current clamps, enabling the logging of a wide range of process parameters.
-
Product
Microwave Leakage Tester
TEK500
-
An easy to use, low cost pass / fail microwave leakage detector suitable for commercial and domestic microwave ovens. It is designed to comply with national standards on permitted exposure levels. The TEK500 includes a self test which simulates a real microwave input to ensure the unit is working correctly at all times.
-
Product
Current Measurement
-
Measurements International Ltd.
No Stabilization Period, No Power Coefficient, No Temperature Coefficient, DC and AC Operation, 3000 A Max Current DC.
-
Product
Digital Clamp Meter
-
A clamp meter is convenient for measuring instruments that allows the measurement of current simply by clamping a wire while being energized without cutting a circuit. In cases of measurement by a multitester and digital multimeter, the circuit must be cut to measure current. In contrast, with a clamp meter, current can be measured simply by clamping a live wire over its sheath. In addition to its simple operation, it allows safe measurement of a higher current.
-
Product
Probe “Socket” Clamps
LCP-S12
-
A simple and cost-effective option for mounting Small-aperture Probes in the probe plate. A Socket Clamp tool is needed for insertion and removal of the clamp in the probe plate
-
Product
Flexible Clamp Meters
-
TES Electrical Electronic Corp.
Three current ranges. Two output sensitivity measuring instruments. Input protection up to 600V. Suitable for any electrical system. Wide bandwith low phase shift.
-
Product
Current Transformers
-
National Meter Industries Inc.
Is an instrument transformer, used along with measuring or protective devices, in which the secondary current is proportional to the primary current (under normal conditions of operation) and differs from it by an angle that is approximately zero.
-
Product
Flexible Rope-Type Current Probe
RCT1A and RCT5A
-
These probes have great bandwidth ensuring accurate measurement even with harmonically distorted wave shapes. For all RCT1A/RCT models, a NIST, NAVLAP, NPL (UKAS) factory traceable calibration certificate and certificate of conformance is supplied. UL/CSA approved materials are used throughout. Three phase and single phase flexible AC current sensors (rope sensors) are available for fast installation in confined spaces, eliminating the need for Electrical Supply Shutdown. Available outputs are 1A @ 2.5VA and 5A @ 0.5VA, this means long cable lengths from current sensor to signal conditioner allow these low VA ratings to be used, even when feeder cable to energy meter distances are large (up to 98 feet / 30 meters)
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-400B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Current Transformers
-
Excellent measurement technology requires high-quality current transformers. The product portfolio comprises a wide range of current transformers for load currents (operating currents) and residual currents (RCM). Different designs cover a variety of installation situations and metrological requirements, and enable retrofitting. AC/DC sensitive measuring current transformers use a special measurement method to detect both AC and DC currents of different frequencies.
-
Product
High Altitude Wiring Clamp
-
Weshine Electric Manufacturing Co., Ltd
1. The operation is simple, through pushing and pulling the special operation lever can realize the clamp mouth free opening and closing, complete the wiring work.2. Connection clamp between the upper and lower jaws of the use of the principle of moving pulley to save the effort, the use of smaller tension can be obtained larger clamping force.3. There is a steel needle inside the clamp mouth to ensure good contact between the clamp mouth and wiring position
-
Product
AC/DC Clamp Milliammeter (CE)
M-700
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High sensitive for low range leakage current.*Suitable for measurement of 4-20mA DC controlled circuit.*DC mV analog signal output.*Lowest influence from Magnetization and Terrestrial magnetism.*Wide measuring ranges up to DC 1000mA and AC 10A.
-
Product
3.5 Digit Handheld Clamp Meters
U1210 Series
-
Measurements of electrical distribution cables can be challenging and risky. For cables up to 2 inches in diameter, the Keysight U1210 Series (U1211A, U1212A, U1213A) handheld amp clamp meters (also known as clamp-on ammeters) enable high-current measurements without breaking the circuit. Plus, they provide an extra layer of protection with CAT IV 600 V and CAT III 1000 V safety ratings and include full digital multimeter (DMM) measurement features.
-
Product
Precision Current Preamplifier
SIM918
-
Stanford Research Systems, Inc.
The SIM918 Current Preamplifier is ideal in applications in which the input offset voltage must be kept to a minimum. The DC voltage difference between the two inputs (current input and voltage bias) is accurately measured every 2 seconds, and is nulled.
-
Product
Auto-ranging Digital Clamp Meter
DCM402
-
Expert Quality, auto and manual ranging clamp meter capable of voltage, current, resistance, diode, continuity, capacitance, frequency, duty cycle and temperature testing. Maximum jaw - opening diameter of 36mm, backlit LCD screen, auto power off, linear bar graph functions and a useful inspection light. Supplied with test leads, temp probe, case and 3 x AAA batteries.
-
Product
DC In AC Clamp Tester
M-800P
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Model 800P is the world’s first clamp meter which can detect small DC current in AC circuit in addition to general AC/DC current measurement.
