-
Product
Radio Test Set
CTS-6000 Series
-
Bring your radio test function into the modern age with the new CTS-6000 Series radio test set. Combining nineinstruments into one, this tester offers fault detection and operational verification of your radio communicationssystem whether in the factory, at the depot, or deployed in the field.
-
Product
Communications Manufacturing Test Set
CMW100
-
The R&S®CMW100 communications manufacturing test set is based on the R&S®CMW platform. The flexible RF interface permits simultaneous testing of up to eight devices. The R&S®CMW100 remote control and measurement concepts are compatible with the R&S®CMW500. The R&S®CMW100 is optimized for cost-effective calibration and verification of wireless devices in non-signaling mode (analyzer/generator). The tester provides a new eco-friendly hardware concept, featuring extremely low energy consumption and a very compact size, making it ideal for use in fully automated robotic production lines. It supports LTE, 5G NR, WLAN, Bluetooth® and IoT technologies, making it ready for today and tomorrow.
-
Product
Three Phase Relay Test Set
RELTEST 1000
-
RELTEST 1000 is a multifunctional relay test set, especially designed for distribution, smart grid and renewable energy plants.
-
Product
Test Port Adapter Set, 2.4 Mm To 3.5 Mm
85130F
-
The Keysight 85130F test port adapter protects the test set port from connecting directly with the device under test. It has a special rugged female connector designed for connecting to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. The set contains a 2.4 mm to PSC-3.5 mm male adapter and a 2.4 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 26 dB or better.
-
Product
Forward Path NPRT 2200 Noise Power Ratio Test Set
NPRT 2200-F
-
The NPRT 2200 measures the NPR of a device across a range of power levels. This test quantifies intermodulation distortion and determines the dynamic range of optical transmitters, amplifiers and other active HFC network devices. The included PC software uses predefined test setups to run a "Power Sweep" series of NPR measurements and graph the results.
-
Product
High Voltage Breakdown Test Sets
HT-Series
-
Dielectric Voltage Withstand Test or High Potential Test (HIPOT test) is a 100% production line test to verify the quality & electrical safety characteristics of products.
-
Product
Single Phase DC Injection Set Kit
PDC120A/PDC200A
-
PDC120A/PDC200A Single Phase DC current injection set kit is portable test set which could generate DC current for the various testings in railway transportation, HVDC converting stations, etc.
-
Product
AC & DC Combined Test Set With / Without Impulse
-
This testing equipment is used in electrical and power industry.
-
Product
High Pressure/Vacuum Set Points (longbody, NEMA 4)
J205LV
-
The J205LV NEMA 4 High Vacuum Low Set Point Vacuum Switches are among our most versatile offering, affording the end user an extensive operating environment and a wide range of set point optionality. These switches are the NEMA 4 rated weather-proof, liquid-resistant version of the J205G, suitable for outside applications or in areas of condensing humidity.
-
Product
Fiber Identifiers & Talk Set
-
Fiber Identifiers and Talk Set are essential installation and maintenance instrument in data networks, CATV and telecommunication networks. Fiber identifier can identify the optical fiber by detecting the optical signals transmitted through the cables. Talk Set combines in one set the functions of both a digital optical phone and a stabilized light source. It is usually used in pairs, and can work over 80km. Fiberinthebox supply different types of Fiber Identifiers and Talk Set to meet you requirement, and they are with rechargeable battery and power supply adapter, so you can use them easily.
-
Product
Engine Speed Control and Measurement (Test Set A)
MS 1100
-
*Checks the parameters such as current, voltage, speed, and turbine gas temperature of 804E and 811 engines Portable instrument*Testing of Automatic engine control system and after burner control system*Simulates the temperature signal derived from the engine TGT (Temperature Gas Turbine) thermocouples*Simulates the speed signal, NL (low pressure shaft speed signal) drive from the L.P shaft Probe*Indicates the current signal to the FCU solenoid derived from the engine control amplifier*Measure the TGT and NL simulated signal at static position*Measure the signal produced by the engine TGT thermocouples*Measure the NL signal produced by the LP shaft*Measure the NH (High-pressure shaft speed) signal produced by HP shaft*Indicates the solenoid current, produced by the engine control amplifier*Indicates the solenoid voltage, produced by the engine control amplifier*Used to test engine in both static and dynamic states
-
Product
Conductor Damage Test Set
CD-2M
-
Is designed to carry out tests specified for Switches used for Domestic and similar applications as included under IS:3854:1997. It is used to ensure that Screwtype terminals of switches are such that they clamp the conductor without causing undue damage to the conductor strands. It is a compact and robust andequipment housed in a bench top enclosure. The CD-2M is motorized to allow easy operation. The Instrument is designed to meet the requirements of IS:3854:1997 and other related specifications.
-
Product
Test Sets For Transformer Industries
-
Contemporary Test Sets For Transformer Industries are developed to recognize the potentially disastrous current transformer errors. They prevent the primary current from overpowering insulation and short circuits. They are used for developing a testing and maintenance plan for addressing the errors before any failure to save money and time. With these powerful test sets, they are sure to perform saturation testing to test the knee point of a signal by comparing primary and secondary windings.
-
Product
Optical Talk Set (Optical Phone & Light Source)
X-5010
-
This is an efficient instrument that combines in one set the functions of both a digital optical phone and a stabilized light source. It is widely used in operations of installation, optical testing, maintenance, CATV and Telecommunication network. It can carry out full-duplex communication with high quality connection and not be affected by distance. With comfortable hand feelings, and nice outside looking, the user can easily operate on this optical tester.
-
Product
Test Set Solutions
-
This product category contains specialized low-PIM filter-based offerings for 3GPP/4G/5G LTE test sets and broadband emissions monitoring.
-
Product
Weapon Control System Test Set
MS 1102
-
- Provides serviceability checks on armament system- Portable instrument- Check the Bomb release sequence, practice bomb release sequence, rocket release sequence, fuzing, and jettison of aircraft stores- Helps to identify faults of conventional armament- Microprocessor based design
-
Product
AC / DC Combined High Voltage Test Set
-
Cambridge Instruments & Engineering Co.
suitable to perform AC High Voltage Power Frequency test on transformers, motors, cables etc. Leakage current can be measured at desired pressure and this set can be used as a source for cable fault burning.
-
Product
Insulated Mini-Alligator Test Lead Set
BU-00285
-
Insulated Mini-Alligator Lead Set • Material: Clip: nickel-plated steel with PVC insulator; Hook-up Wire: #22 (19/34) AWG copper with 105° C PVC insulation • Length: 18”(.46 m) • Colors: Includes 2 each: Black, Red, Yellow, Green, White • Rating: Hands free testing at 300V, 5 Amps
-
Product
Hand Held Loss Test Set with Return Loss Option
LTSH1315
-
The KD Optics LTSH1315 is a combined laser or LED source and power meter designed to make attenuation testing in the field easy, reliable and consistent. A return loss option is available for 850nm multimode, 1310nm and 1550nm singlemode.
-
Product
Hand Held Sheet Resistance Measurement Instrument[Replaceable Probe Set (Non-destructive Probe & Contact Probe) ]
DUORES
-
Easy to measure sheet resistance & carry aroundReplaceable hand-held probes for Non-destructive & Contact type
-
Product
Crossed Roller Rail Sets
-
Del-Tron’s crossed roller rail sets (or crossed roller bearings) are compact, precision rail sets that can support and guide high loads with high accuracy, excellent repeatability, and low friction. A complete range of profiles are offered with roller diameters ranging from 1.5mm up to 6 millimeters, providing load carrying capacities to 2800 lbs. For vertical applications or applications involving high acceleration or deceleration forces you may want to consider our Anti-Creep crossed roller rail sets.
-
Product
Digital Set Point Relay For Voltage
-
These Digital set point relay for voltage (type mrd2011-v), which have two independent outputs and can be used to control the under voltage and over voltage operations. The two independent outputs are programmed/set in a range of 0 vac to 700 vac according to the application needed.
-
Product
Test Program Sets & Custom System Level Software
-
WesTest Engineering Corporation
WesTest Engineering Corporation offers turnkey test solutions for the military and aerospace sectors. Our engineering capabilities present an unmatched ability to take customer test requirements and design, developand integrate Test Program Sets (TPS) with diagnostics to the component level. This is further supported by a full complement of documentation, from Test Requirements Documents, to TPS Flowcharts, to Test Reports.With 36 years’ experience and 1000+ TPSs in our history, the WesTest Engineering Staff remains as one of the top notch senior staff’s in the TPS sector today. Our leadership and program management have the historicalexperience to lead WesTest capability to meet the customer’s requirement.
-
Product
Tactical Radio Test Set
CTS-6100
-
The CTS-6100 brings an entire test bench to your front lines. Enable your technicians to detect equipment faults and verify operational capabilities at the I- and O-levels, saving valuable diagnostic time and cost.
-
Product
Multifunction Substation Test Set
STS 4000
-
STS 4000 is a multifunction substation maintenance & commissioning test system for current, voltage and power transformers, designed to perform primary tests requested in substations commissioning. It allows to perform accurate tests on CTs, VTs, PTs and ground grid.
-
Product
Optical Loss Test Set
KI23424OL-INGAAS-APC
-
A Quad Two-Way Optical Loss Test set / OLTS fiber tester that's perfect for medium to ultra high fiber count loss, length & optical return loss testing applications on both multimode and single mode fiber with APC connectors on both ports at 850 / 1330nm 1310/1550 nm. A pair of these compact SM & MM instruments set new standards of productivity, ultra-stable source accuracy and ease of use.
-
Product
Semi-Rigid Cable Set, 3.5 Mm (Test Port) To 3.5 Mm
85131D
-
The Keysight 85131D is an 53 cm (21 in) long1 semi-rigid cable set composed of a 3.5 mm female2 to PSC-3.5 mm female connector and a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss of 16 dB or better. Insertion loss is 0.3 * sqrt(f) + 0.2 dB, where f is frequency in GHz, for the test port connector and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability1 of the Keysight 85131D is less than 0.06 dB and phase is 0.16 * f + 0.5, where f is frequency in GHz.
-
Product
SM & MM Quad Optical Loss Test Set
KI2724-INGAAS-APC
-
A SM & MM Quad Optical Loss Test Set used to test power, insertion loss, continuity and faults on multimode and single mode fiber with an APC connector at 850 / 1300 nm & 1310 / 1550 nm. In a small package, it provides a powerful solution to improve test flexibility and productivity.
-
Product
Two-Way Optical Loss Test Set
KI23427OLF-INGAAS-APC
-
A Two-Way Optical Loss Test set (OLTS) that's perfect for medium to ultra high fiber count loss, length and optical return loss testing applications on single mode fiber with an APC connector at triple 1310 / 1490 / 1550 nm. A pair of these compact instruments set new standards of productivity, accuracy and ease of use. The 650 nm VFL is on a separate port.
-
Product
Free Imperas RISC-V Instruction Set Simulator
riscvOVPsim
-
*RiscvOVPsim - RISC-V Instruction Set Simulator (ISS) - fast, simple, easy to use, cross software development for embedded systems*The riscvOVPsim ISS is an ideal starting point for an embedded software development project. *RiscvOVPsim allows the development and debug of code for the target RISC-V processor on an x86 host PC with the minimum of setup and effort. It simply requires the cross compilation of your application and running riscvOVPsim with an argument to specify the name of the application object.
