-
product
Optical Path Converter
LS512A/LS512B
There are many LED manufactories using two integrating spheres and one spectrophotometer to do test. The previous testing way is: when you use big sphere to test, the customer need to connect the detector cable and optical fiber from the Spectrophotometer to the big sphere, after the calibrating and then you can do the test. When you use the small sphere, you need to take away the detector cable and optical fiber from the big sphere to the small sphere, then need to calibrate again. It is too troublesome to take out the detector cable and optical fiber between the big sphere and small sphere, and you need to calibrate again for every change. The frequent change will also shorten the life of the detector cable and optical fiber.
-
product
4-20mA Sensor Converter
ENVIROMUX-S420MA-24V
External RJ45 device monitors up to two 4-20 mA analog sensors. Supports ISA Type 2, ISA Type 3, and ISA Type 4 sensors. Provides 24VDC, 25mA for each sensor. Connector: Screw Terminal, 8-position. Supports CAT5/5e/6 cable up to 500 ft. (152 m). Includes Mounting Hardware. Powered by ENVIROMUX-2D/5D/16D. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: RoHS.
-
product
Airborne Frequency Converter
AFC Series
Behlman’s AFC-7000-1 & -2 and AFC-7003, frequency converter are designed to convert three-phase aircraft power to regulated single-phase (115 or 230 VAC) or three-phase (115/200 VAC) at 50 Hz, 60 Hz or 400 Hz. They are ruggedly built to support aircraft takeoffs and landings and designed to meet the input power requirements of MIL-STD-704 and RTCA-DO-160.
-
product
Serial Data Converters
CONV232/485 and CONV232/422
CONV232/485 and CONV232/422 convert between RS-232 communications (as used by the COM1 and COM2 ports standard on most motherboards) and balanced-mode, long distance RS-485 and RS-422 communications. CONV232/485 was designed for use with our REMOTE ACCES line when there is no RS-485 port on your PC, but may also be used in other, similar applications.
-
product
Optical Fiber Converters
Optical Fiber Transmission products play an important role in systems for wide-band analog signals and digital signals with high data rates. They send and receive data from point-to-point via a network, thus the fundamental function of all fiber systems from small to large. A lot of optical fiber transmission products are available from Fiberinthebox, such as Optical Fiber Transceivers, Fiber Media & Protocol Converters, Optical Multiplexers, Fiber optic modems, Optical Switches, Network Interface Cards, and PON & AON. Our optical fiber transmission products are developed and manufactured to provide reliable, durable performance.
-
product
IRIG B to NTP/SNTP Converter
Signals & Systems India Private Limited
IRIG B TO NTP/SNTP CONVERTER – SPC-INS-1010 is a compact DIN rail mountable protocol converter unit which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using IRIG-B signal obtained from GPS receiver. It provides nanosecond accuracy when external time references are not available. It has the storage facility to store the system log file. It delivers NTP, SNTP, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through Web-based application. It supports a wide range of power supply input either 90V-260V AC/DC or 18-36VDC or 36V-72VDC.
-
product
Binary to BCD Converter
BAC200
Computer Conversions Corporation
The BAC series of Binary to BCD converters will convert binary angle data to 5 digit BCD data scaled in degrees and decimal fractions of degrees. Units with display and/or data outputs are available. Custom scaling of the output to represent actual physical units of measure can be provided easily (i.e.: feet, lbs., meters, mills, etc.)
-
product
Sample Rate Converters
Analog Devices’ portfolio of sample rate converters features industry-leading performance in both audio performance and conversion ratios. These converters can be used in high end consumer applications, as well as in price conscious consumer applications.
-
product
D/A Converter
DA-4130
The DA-4130 D/A converter converts BCD output signal from Ono Sokki's digital gauge DG-4000 series, RV series reversible counter or other devices into analog signal to be recorded with pen recorder, etc.
-
product
Simultaneous Sampling A/D Converters
Analog Devices simultaneous sampling precision A/D converters offer two to eight discrete ADCs in a single package, allow two to 12 channels, and span resolutions from kSPS to 5 MSPS. Providing the industry-leading noise, linearity, and dynamic range performance, ADI has a simultaneous precision converter to meet your speed, power, and size needs. Simultaneous sampling ADCs enable users to convert multiple signals concurrently and preserve phase information.
-
product
Balanced O/E Converter
TIA-527
The TIA-527 balanced optical to electrical converter provides adjustable gain and a bandwidth of DC to 125 MHz. It is useful for coherent heterodyne detection applications, spectroscopy and similar applications for which the ability to discern small variations in signal strength in two optical paths is critical..
-
product
O/E Converter
TIA-1200
The TIA-1200 optical to electrical converter is a convenient battery powered wideband detection system for fibre optic applications. With a typical bandwidth of DC to 12 GHz (min. 10 GHz), it accurately provides an electrical replica of the optical signal presented to it. It is intended to drive a 50 ohm cable terminated in its characteristic impedance.
-
product
Low Power DC/DC Converters
The 4:1 Input Voltage 75 Watt WDE includes remote sensing, ultra-wide output voltage trim, and remote ON/ OFF. The digital power management enables increased reliability, configurability, voltage / current precision and fault management.
-
product
I/O's & Converters
Rishabh Instruments Pvt. Ltd.,
Module of logic outputs. Control of actuators from monitoring systems or PLC over RS485. 4 relay outputs or 8 OC outputs steered through RS-485/Modbus. Fixing on a TS35 rail. Full galvanic separation between outputs (for relay outputs). Configuration through free LPConfig software.
-
product
DC/DC Converter 192 W
HP2540-9TB1G
DC/DC converter with 192 W from Bel Power Solutions | input ranges 16.8 - 137.5 VDC | two outputs at 15 V | operates in temperatures from -40 to +71 °C | provides 10 ms hold up time | 20 mm heatsink included
-
product
Interface & Level Converters
Advanced Science and Novel Technology, Co., Inc.
2-channel LVDS-to-CMOS converter (Receiver) and 2-channel CMOS-to-LVDS converter (Transmitter)Optional signal splitter function with selectable inversionOptional DS (Data/Strobe) encoding/decoding for compatibility with Space Wire StandardProgrammable LVDS/CML/ECL Receiver input interfaceTrue LVDS Transmitter output interfaceFlexible selection of enabling and operational modes of the channelsHigh-impedance states of disabled CMOS outputsSingle +3.3V power supplyIndustrial temperature range
-
product
DC toDC Converters
Low Cost Single Dual and Triple outputs Isolated Outputs Low Ripple, Regulated Outputs Standard packages and pin outs Custom Designs availableNew Miniature V3 Series features HighVoltage Isolation, SIP and DIP packages
-
product
Multichannel Voltage Output D/A Converters
Analog Devices offers an industry-leading family of multichannel voltage output D/A converters (DACs), covering 8-bit to 16-bit resolutions, from 2-channel up to 40-channel density, and serial SPI or I2C interfaces. This family of precision D/A converters are in demand for applications that require high channel density and a small form factor, such as optical communications, analog output modules, or LED displays. ADI’s multichannel voltage output D/A converters provide features such as the availability of multiple independent output spans, system calibration functions that allow user-programmable offset and gain, or D/A converter increment/decrement functionality, which reduces the need to add external precision gain stages and facilitates the use of this family of D/A converters.
-
product
DC/DC Converter 1000 W
CRS-1000-6479-C
DC/DC converter with 1000 W from Premium | input ranges 28.8 - 60 VDC | output 48 V | operates in temperatures from -25 to +70 °C | designed according to EN50155
-
-
product
DC/DC Converter 150 W
CQB150W-110S3V3
DC/DC converter with 150 W from Cincon | input ranges 43 - 160 VDC | output 3.3 V | operates in temperature from -40 to +105 °C | according to EN45545-2 fire and smoke
-
product
Catalytic Converter Measurement
OMCAT
OMCAT catalytic converter measuring systems provide a fast and efficient means of carrying out complex geometrical measurements on exhaust catalytic converters and of determining the gap bulk density (GBD). OMCAT measuring systems feature innovative measurement functions combined with reliable technology. High measurement speed and accuracy and high availability due to their rugged construction are the major strengths of these systems which come to the fore in the harsh conditions which prevail in production environments.
-
product
DC/DC Converter 2 W
REM2-0512D
DC/DC converter 2 W from Recom | input ranges 4.5 - 5.5 VDC | outputs +/-12 V | operates in ambient temperature from -40 to +95 °C
-
product
Serial To Ethernet Converter & Device Server
SERIP-100
SERIP-100 is proconX' low-cost Industrial device server offering one or two software selectable RS-232/422/485 serial ports and a 10 Mbit Ethernet port.
-
product
Video Format Converter
RVG-FC1
Curtiss-Wright Defense Solutions
Video management integration is often complex and burdened with problems that arise from integrating legacy equipment with the latest video sources. The Curtiss-Wright Rugged Video Gateway Format Converter (RVG-FC1) provides a flexible building block capable of converting between a range of video formats and resolutions (15 different formats and resolutions are supported).
-
product
8 channel 16 bit Digital to Analog
CPCI-DA8-1
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system. The CPCI-DA8 is supported by ALPHI Technology under Windows NT by a Board Support Package which is supplied with the card. Other documentationsupplied with the card will describe this support in full detail.
-
product
Modbus Register Converter
Model 2390
* Converts Modbus Registers and variables for replacement Modbus devices.* Maintain existing software when upgrading Modbus systems.* Provides serial control of Modbus RTU devices from any ASCII source.* User defined Register Conversion Table supports all Modbus RTU devices.* Internal Register Conversion Tables for Watlow F4-to-EZ-ZONE and F4-to-F4T conversion.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes baud rate conversion capability.* Uses SCPI commands to load the Conversion Table and set serial settings.* Small metal case mounts on a DIN rail or on any flat panel.* 239x Table Loader Program uploads the 2390 Register Conversion Table from an Excel csv file.* 239x Serial Keyboard Program provides instant control of the 2390 and Modbus Slave Devices without writing a program.
-
product
Fiber Optic/BNC Converters
The active receiver and transmitter require power while the passive transmitter requires a TTL signal that is capable of driving 75 mA.
-
product
Ethernet Media Converter
MC-E Series
The MultiLink MC-E series makes it easy to use the power of optical fiber for extending Ethernet networks to remote locations. The fiber port is available in a variety of connector types and can support extremely long distance connections of up to 40km. With a built-in 2 copper port switch, it's also the fastest way to add multiple Ethernet drops to remote locations.
-
product
Binary to BCD Converter
BAC300
Computer Conversions Corporation
The BAC series of Binary to BCD converters will convert binary angle data to 5 digit BCD data scaled in degrees and decimal fractions of degrees. Units with display and/or data outputs are available. Custom scaling of the output to represent actual physical units of measure can be provided easily (i.e.: feet, lbs., meters, mills, etc.) They will also accept encoder outputs and display them at extremely low cost when compared to previous solutions.
