-
Product
High-Power Noise Sources
-
These modules not only contain the noise diode circuitry, but also gain stages to boost the output power. While lower frequencies (under 2 GHz) are most common, Mercury produces powerful amplified noise modules up to 18 GHz. Noise modules are available in coaxial, surface mount and pin type construction. TTL control options are available.
-
Product
AC Power Sources
Ls-Lx Series
-
AMETEK Programmable Power, Inc.
The Ls/Lx Series is a completely improved new product based on the popular California Instruments L Series. Both the Ls and Lx feature many basic AC Source capabilities at a very reasonable price. For more information on either product, please click on the product tab on the right.
-
Product
Current Source
M151
-
Clarke-Hess Communications Research
The Model M151 is a stable high current calibrator up to 120 A. Basic accuracy is 0.035 %. It can be controlled viaRS232 or GPIB interface. The Model 151 can function in a simulated amplifier mode to increase the current capabilityof any multifunction calibrator. It is suitable for power meter calibration because it can be synchronized with the inputsignal not only in amplitude but also in frequency and phase. The current terminals are isolated up to 450 Vpk againstcase (protective earth).
-
Product
Noise Sources
WGNS
-
The system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device operating in the 26.5 – 170GHz range on wafer as well as in benchtop applications. Farran offers the WGNS series of noise sources to be used in conjunction with the FBC down converters for use as frequency extenders for noise figure measurement test system.
-
Product
Standard Light Source
SLS-50W
-
OSRAM Standard Lamp to calibrate the spectrum and luminous flux with Lisun Lab certification. The data can be traced NIM. The Standard Lamp Source is used to calibrate the integrating sphere system. The different size of Integrating Sphere should choose the right power of standard lamp source.
-
Product
Utility Power Source
SE-UDPS
-
Load boards for applications like mixed signal, analog and RF require active components. To drive these active components multiple utility power supplies are needed. The SE-UDPS from Salland Engineering is an economical way of adding more utility power supplies to your Advantest™ V93K to drive op-amps, buffers, relays and switches. The SE-UDPS extends the usefulness of your current fleet of V93Ks. You can also minimize the need to add external power supplies on your load boards.
-
Product
UV Plasma Sources
UVS300|UVS 10/35
-
The UVS300 and UVS 10/35 are UV Plasma sources with high intensity, working with different gases.
-
Product
PXIe-4145, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit
782435-01
-
PXIe, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit - The PXIe-4145 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4 wire) sensing for accurate measurements. The fast sample rate of the PXIe-4145 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4145 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
Light Sources
-
For applications such as transmission, absorption, and reflection, illumination sources are needed. Avantes offers a wide range of different types of light sources, to suit your specific application needs. An overview of the different types of light sources can be found below.
-
Product
Optical Light Sources
FLS200 Series
-
Shanghai Tarluz Telecom Tech Co., LTD
FLS200 Optical Light source could provide maximum 4 wavelengths in one unit, customer could select arbitrary four output wavelengths from 650nm, 850nm, 1300nm, 1310nm, 1490nm, 1550nm. The unit support Single mode and Multimode (50/125um or 62.5/125um MM fiber) optical cable in one unit. It could support FC, SC, ST, LC and 2.5mm universal optical connector.
-
Product
Dopant Source
-
Attain precise and stable control of relatively low fluxes for dopant constituents in molecular beam epitaxy (MBE) through this compact dopant source. Its small thermal mass gives it excellent responsiveness, reproducibility, and stabilization for advanced doping profiles, plus consistent flux uniformity across an entire platen. Efficient cell heating minimizes thermal load.
-
Product
PXIe-4143, 4-Channel, ±24 V, 150 mA Precision PXI Source Measure Unit
782431-01
-
PXIe, 4-Channel, ±24 V, 150 mA Precision PXI Source Measure Unit - The PXIe-4143 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation and each channel has integrated remote (4-wire) sensing for accurate measurements. The fast sample rate of the PXIe-4143 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4143 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
XRT Source Brighthawk
-
The BRIGHTHAWK NT100 is a performance-leading microfocus X-ray tube comprising proprietary technology to achieve a high brightness output. The tube consists of a LaB6 crystal source for generation of the electron beam, a magnetic beam steering system, and a tungsten target for X-ray photon emission. The components are mounted in a precision-engineering housing and held at ultra-low vacuum levels for long-life performance. Following on from the successful 3rd generation tube, this 4th generation of tube across a wide energy range from 30 kV to 160 kV is highly configurable through a software interface to the internal control board, which is connected via an optical interface (through an Ethernet converter).
-
Product
Point Source
KF Series
-
All loudspeaker systems in the KF Series feature three-way design. Each sub-series applies three-way design to meet a particular set of requirements.
-
Product
Excitation Light Source
-
Various spectral irradiation is possible by combining various light sources + spectroscope + irradiation system.We will also respond to special order correspondence. We will provide light suitable for your desired intensity such as light intensity and wavelength.
-
Product
RF Noise Source
NS-3
-
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
Product
Source Phase Control
S96088B
-
The S96088B allows users to set calibrated, arbitrary phase differences between two signal sources running on the E5080B ENA.
-
Product
AC Power Source
SPS-100
-
Kongter Test & Measurement Co., Limited
SPS-100 is designed for various tests of analog and digital AC Voltage meter and Current meter, Single/three phase active and reactive power meter, Phase angle meter, Single/three phase power factor meter, frequency meter, and synchronous-meter, Single/three phase active and reactive power meter; it also outputs 2nd ~63rd harmonics.
-
Product
Light Source
pE-300ultra
-
CoolLED's pE-300ultrais a fluorescence microscopy light source which offers intense, broad-spectrum LED illumination for imaging most common fluorescent stains. Users have access to both microsecond switching via multiple TTL inputs and the ability to mount inline excitation filters. This, when paired with today's high performance multi band filter sets, facilitates imaging traditionally done via a white light source and a filter wheel, with all the benefits of LED.
-
Product
10-Ch. 0… 5V 400mA Isolated
YAVAP955
-
The YAV board AP955 contents 10 CAN Bus programmable bipolar Isolated precision and low noise 0 to 5VDC voltage sources up to 400mA output, with Tripaddle VPC connector.
-
Product
Primary Reference Source
VCH-1008C
-
The primary reference source VCH-1008C is designed to form highly stable signals used in digital communication networks as the first level of the hierarchy. The use of digital technologies for the formation and processing of signals allows you to realize the best stability characteristics.
-
Product
AC Power Sources
-
AMETEK Programmable Power, Inc.
AMETEK Programmable Power's AC power sources range from 800VA to 480kVA. From compliance test systems to rack-mounted industrial power subsystems, AMETEK Programmable Power is the leader in the design and manufacture of precision, programmable AC power sources used in R&D, test and measurement, avionics testing, inverter testing, arbitrary waveform generation, bulk power and power conditioning applications across a wide variety of industrial segments.
-
Product
Optical Light Source
TM3111
-
TM3111 optical light source is a handheld optical light source, It can provide 1 to 6 wavelengths output to satisfy specific requirements including the 650nm visible light source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber, as well as other wavelengths according to customer’s needs.
-
Product
AC Source
AFC
-
The AFC Series products are single and three phase AC Power sources ranging from 0.5kVA to 2000kVA. This AFC series has a continuous and adjustable output voltage between 5~300V. This allows for quick and convenient 3 scales of preset voltage for high and low voltage simulation. Power is supplied by state-of-the-art IBGT pulse width-modulated power amplifiers resulting in highly efficient power conversion, compact design and maximized performance. With up to 90% efficiency the AFC minimizes heat dissipation so less infrastructure cooling is required.
-
Product
LED Uniform Light Sources
-
Integrating sphere light source with LED illuminants (white, RGB-colored, NIR). Options available like variable output control and monitor detectors. We are experts in providing customer specific systems. Please contact us for all possible solutions and finding your perfect solutions. E.g. for EMVA 1288 Standard.
-
Product
Omnidirectional Source
BAS001
-
The BAS001 Source is designed to generate omnidirectional sound fields for making standard compliant measurements including: reverberation time (ISO 3382, ASTM E2235), building acoustics (insertion loss, acoustic absorption area, etc: ISO 140-4 ISO 140-3, ASTM E336, ASTM E90, DIN 55 210). The BAS001 is typically used to saturate a room with a uniform acoustic field. The available high-efficiency power amplifier has no fan for cooling, allowing measurements in quiet environments, like those in reverberation time applications.
-
Product
Specialty Sources
-
When conventional sources hit their limits, specialty sources step in. These custom-designed plasma and vapor sources are engineered for III-V MBE and compound semiconductor applications where unique material delivery and control are critical.
-
Product
Noise Sources
-
This power amplifier ensures that you get the maximum sound pressure level out of the Norsonic range of speakers.
-
Product
Laser Source
-
Is an Amplified Spontaneous Emission (ASE) based broadband light source, designed for general laboratory applications. It is a reliable and cost-effective unit that can be ordered with multi channel options. The LD operating temperature and drive current are precisely monitored by a micro-controller to ensure constant output power and emission wavelength stability. With compact size configuration, it’s also suitable for OEM integration, User can control the ASE source output power level by adjusting the drive current along with remote status monitoring, contact Optilab for more information.
-
Product
DC Sources
-
Electronic Test & Power Systems
Adjustable constant voltage and constant current sources are provided across the entire DC source range. Additionally constant power operation is standard on the high power DC supplies and optional on the medium power models. Modular high current DC power supply systems providing up to 2kV at 2MW can be assembled.A variety of interfaces are available. Analogue, RS232, CAN, RS485, Ethernet or IEEE 488.2 can be specified for most units. LabVIEW drivers are also offered to aid system integration.
