-
Product
PXI-8368, MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module
783934-01
-
MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module—The PXI‑8368 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8366 through a copper, x1 MXI‑Express cable. The fiber-optic cabling of the PXI‑8368 provides electrical isolation between the PC and PXI chassis, as well as cabling up to 200 m per link.
-
Product
Photonic Electric Field Sensor System
Model No. 200-04
-
SRICO Model No. 200-04 Photonic Electric Field Sensor System has the ability to measure electric field with minimal disturbance to the field. The lightweight fiber-optic cables allow for easy placement of the E-field probe, allowing it to be unencumbered by the use of heavy coaxial cables that may disturb the field being measured. The dielectric E-field probe is electrically passive.
-
Product
High Speed Fiber-Optic Detectors
-
High speed fiber-optic detectors use special photodiodes with high speed electronic circuits to convert fast pulses in optical fibers to electrical signals for measurement. Unlike our optical receivers, these photodetectors do not include a transimpedance amplifier.
-
Product
Optical Light Source
CARY-LS300B
-
The CARY-LS300B optical light source provide 1310/1490/1550 nm three outputwavelengths to meet specific application requirements. It is a idea solution for the fiberoptic network characterization, out-door network construction inspection and lab application.
-
Product
High Speed And High Resolution Cameras (PCI Cameras)
XiB
-
*High speed interface with bandwidth of 20 GBit up to 64 Gbit / sec*CMOSIS / ams sensors: CMV12000, CMV20000, CMV50000*High image resolution and high throughput with 12 Mpix, 20 and 50 Megapixel*Speed of 133 - 333 Fps, 33 and 30 Fps respectively*Fast speed models with 1 Mpix at 3500 and HD at 2500 Fps*Robust PCI Express and Power/GPIO connectors*Integrated Canon EF-mount control with dynamic aperture and focus control*Support for Windows, macOS, Linux, ARM*Suitable for OEM customization and Embedded vision systems*Distances up to 300m over fiberoptic cable*Compact housing: 60 x 60 x 38 mm
-
-
Product
One-Channel Variable Optical Attenuator
N7761A
-
The N7761A attenuator is an extension to Keysight's high density N77xx-family that establishes a new standard in space-saving fiberoptic instrumentation.
-
Product
Miniature 12G/3G/HD-SDI Fiber Transport
SilverBULLET Series
-
Sometimes you just need that “silver bullet” - a simple solution that solves problems. Maybe it’s a quick connection to support temporary video and audio feeds, or perhaps just a rock-solid fiber-optic connection for single-link transport to and from a camera. MultiDyne’s SilverBullet Series offers an economical solution for broadcast-quality signal transmission on single-mode fiber. At just three inches, the SilverBullet offers a compact, interlocking architecture to ensure robust links that can fit just about anywhere. SilverBullets come in a compact carrying case that includes the DC power supplies. Ideal for a wide variety of broadcast and professional AV applications including field production, remote camera links, courtesy feeds, cross-campus production and pre-fibered venues.
-
Product
Fiberoptic Repeaters
-
*Cost effective task specific Fiber Optic Solutions for Satellite Radio and GPS over Fiber*End to end solutions complete with RF to Optical and Optical to RF component*Flexible powering options including DC over hybrid cable, local 48 VDC and AC*Utilizes industry standard fiber cables and connectors
-
Product
Fiber-Optic Transmission
-
Fiber optic transmission systems all use data links that work similar to the diagram shown above. Each fiber link consists of a transmitter on one end of a fiber and a receiver on the other end. Most systems operate by transmitting in one direction on one fiber and in the reverse direction on another fiber for full duplex operation. It's possible to transmit both directions on one fiber but it requires couplers to do so and fiber is less expensive than couplers. A FTTH passive optical network (PON) is one of the only systems using bidirectional transmission over a single fiber because its network architecture is based around couplers already.
-
Product
S2 Blinx Digital Sensors
ULP-S2 BLINX
-
The Universal LightProbe S2 Blinx Digital is designed for the simple ON/OFF test of any color blinking or steady-state LED, for fast results with a digital output. The Universal LightProbe S2 Blinx Digital Sensors check the ON/OFF status of any color LED, whether stable or blinking/pulsed, up to a rate of 15 Hz, and provide a Logic “1” output (5 volts) only if the LED is “ON” and a Logic “0” if the LED is “OFF.”Operating temperature range: 0oC to 70oCPower consumption: Operates from +5, 12, 24 or 28 volts D.C., at 6mA max.Voltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Load: 20mA max. (Source/Sink). Non-inductiveOutput Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <66mS, shorter for brighter LEDsFiber-Optic Probes: Wide Aperture Fiber-Optic Probe recomended
-
Product
Throwdown Fiber Transport & Converters
NanoBriX Series
-
We often forget all that happens along the media signal journey. Video and audio signals are converted, equalized and re-clocked as they move on and off fiber-optic networks. These same signals are manipulated and multiplexed as they are distributed through studio, venue and campus infrastructure on their way to headends and destination points. Audio signals are embedded and de-embedded alongside video streams, and properly mixed for varied broadcast and playout services. It’s almost too much to keep up with. MultiDyne’s NanoBrix Series assures that these many stages of the signal lifecycle are reliably addressed in one complete family. NanoBrix offers a comprehensive product line of miniature, rugged, quick-connecting throwdown solutions for temporary or permanent applications, including live TV productions, sporting venues, and broadcast facilities.
-
Product
Reflective Memory PCIE card
PCIE-5565PIORC
-
The PCIE-5565PIORC low profile PCI Express (PCIe) Reflective Memory node card provides a high-speed, low latency, deterministic interface that allows data to be shared between up to 256 independent systems (nodes) at rates up to 170 Mbyte/s. Each Reflective Memory board may be configured with 128 MB or 256 MB of onboard SDRAM.The local SDRAM provides fast Read access times to stored data. Writes are stored in local SDRAM and broadcast over a high speed fiber-optic data path to other Reflective Memory nodes.
-
Product
FOCL Reference Signal Modem
VCH-607
-
FOCL reference signal modem VCH-607 is designed to receive and transmit electrical signals with a nominal frequency of 100 MHz through a fiber-optic system and generate electrical signals with a nominal frequency of 5 and 10 MHz, coherent with the input signal. Reception and transmission through the FOCL is provided using a pair of modems: one is configured as a Transmitter and is installed at the end of the FOCL where the signal source is located, the second is configured as a Receiver and is installed at the opposite end of the FOCL.
-
Product
High-Speed, Fiber-Optic Reference Transmitters
-
Thorlabs' Reference Transmitters are designed for high-speed fiber optic test and measurement applications. They are fully-integrated and user-configurable solutions based on proven lithium niobate (LiNbO3) modulator technology driven by high-fidelity RF amplifiers.
-
Product
LED Test
-
Universal LightProbe Penta sensors are Optomistic Products' most popular LED test sensor, relied upon for their versatility in accommodating most LED test applications for color and intensity. The Penta Sensor provides analog voltage outputs, and features built-in color binning, eliminating the need to convert LED wavelength to visual color in the ATE software, and saving valuable processing time. For use with any of the Universal LightProbe Fiber-Optic Probes.
-
Product
S2 Unicolor Digital Sensors
ULP-S2 SCC
-
The Universal LightProbe S2 Unicolor Digital Sensor is pre-programmed to respond only to a specific color LED, including blue, green, yellow, orange, red, plus white. The Universal LightProbe S2 Unicolor Digital Sensor is designed for the simple ON/OFF test and color check of a single color LED, with a digital output, quickly determining PASS/FAIL status without further processing by Automatic Test Equipment. The Universal LightProbe S2 Unicolor Digital sensor provides the simplest and fastest interface to Automatic Test Equipment (ATE).Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts, at 6mA max.; less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <10mS capture time; <65mS overall response timeFiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
Product
Fiberoptics
401/402LZ
-
Antenna Technology Communications, Inc.
The 401/402LZ is a outdoor/indoor mounted fiber optic transmitter for RF signals in the satellite L-Band or wider frequency range. It accepts a single RF input on coaxial cable and provides a single output for optical transmission. Up to four 401/402LZ’s may be installed in the ATCi Link4i chassis.
-
Product
1310/1490/1550 Nm DFB-LD For Fiberoptic Communications
-
RV2X6376A Series of directly modulated laser (DML) diodes deliver 25 Gbps x four wavelengths as the light source in 100 Gbps optical transceivers that enable high-speed communications inside 4.9G and 5G LTE base stations, and between data center routers and servers. The RV2X6376A Series are the industry’s first industrial-temperature (-40°C to 95°C) DML diodes that support full 25 Gbps speed (per individual laser) without cooling.
-
Product
RGB Digital Fiberoptic Amplifier
CZ-V20 Series
-
SUPER HIGH POWER RGB sensor Industry's best color differentiation. High resolution amplifier for triple 16-bit calculation. New Luster Detection Sensor Head. Dual digital display & Direct access. New UV sensor head for fluorescent Detection. Three detection modes for every target [Super I / C' / C+I]
-
Product
S2 Spectra Sensors
ULP-S2 WBI/V
-
The ULP S2 Spectra Sensor tests for LED intensity, and for any color in the visual spectrum, plus white. The S2 Spectra Sensor is well-suited for the test of “boundary” color LEDs, as it can unambiguously and repeatedly distinguish between not only adjacent visual colors such as green and yellow, but it can determine different hues of the same color such as yellow and amber, regardless of LED intensity. Implemented in a unique and customizable 2-Part solution, the S2 Spectra Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsOutput Pins: 4 gold-plated standard wire-wrap pins (0.025 in. sq.)Output Loads: ‘Int.’& ‘Color’- 2Kohms min., 100pF max.Sensor Size: 0.560 in. dia x 1.38 in. long.Typical response time: Typical response time: <10mS capture time; <100mS overall response timefor color and intensity simultaneouslyFiber-Optic Probes: Can be paired with any Universal LightProbe Fiber-Optic Probe
-
Product
PIN-TIA
-
The fiber-optic coaxial PIN-TIA receiver module is designed for SONET/SDH fiber-optical communicationnetworks, using reliable InGaAs PIN photodiode (PD) highly integrated with low noise transimpedence amplifier(TIA) to convert a long wavelength input optical signal into a differential (or single) output. It is a highly reliablemodule with excellent performance.
