-
product
Voltage Meter MDN8I-PXIe
MDN8I-PXIe
The MDN8I-PXIe module is made in the PXIe standard and is designed to measure instantaneous voltage values over eight isolated channels with differential inputs.
-
product
Antenna Switch
SixPak
The SixPak has two components: a relay matrix and a control box, there are several options for the controller.The relay matrix allows the selection of any 6 antennas by 2 radios or feedlines. Its lockout circuitry prevents both radios from selecting the same antenna. (The 6x1 type of SixPak is now replaced by our RatPak remote 6 way antenna switch.)The usual set-up has one SixPak dual rotary control box, which is manually operated from the radios positions. The control box for the 6x2 contains two rotary switches and 12 LEDs, so the operator can see which antennas are selected.
-
product
PCI Express Passive Switches
MAX4889
High-Speed PCI Express Passive Switches Enable Gen I Switching
-
product
PXI/PXIe Switched Guard Matrix, 16x4
40-590-101
The 40-590-101 (PXI) and 42-590-101 (PXIe) are modules that provide a switched guard 16x4 matrix solution with up to 1012 Ω channel to channel and channel-to-ground isolation.
-
product
Low PIM Coaxial Switch, DC to 4 GHz, SP4T
87104P
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104P is a low PIM SP4T coaxial switch, operating from DC to 4 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 4 Channel
50-201-004
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, Broad R-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
product
Peak Voltage Measurement
In high voltage measurement technology, the peak value, or the effective value, of the voltage is determined in accordance with VDE 0432 or IECV 60060. The peak voltage measuring device from MPS Mess- & Prüfsysteme GmbH can measure these two values in connection with a high voltage divider (capacitive or resistive). In the event of flashovers in the high-voltage circuit, this is indicated in the SMG.
-
product
Attenuation 100 High Voltage Passive Probe
Safe high voltage probe solutions for ground-referenced voltage testing. It is critical to safely and accurately capture real-time signal information from "elevated" or "floating" voltage systems.
-
product
Development Switch
TTESwitch Lab Space
The TTESwitch Lab Space supports laboratory testing efforts of Time-Triggered Ethernet applications; user development costs can be reduced by using the internal TTESwitch Controller HiRel ASIC that is also used in flight equipment. With advanced features like speeds of up to 1 Gbit/s, flexible physical layer configuration and three supported traffic classes, it is the optimal switching solution for a large variety of application areas. TTEthernet is a fault-tolerant, real-time communication protocol for safety-relevant systems integrating Ethernet and TTEthernet data flows onto one physical infrastructure.
-
product
Voltage Breakdown Testing Machine
DRK218
Shandong Drick Instruments Co., Ltd.
DRK218 breakdown voltage tester is controlled by the computer, through a new smart digital integrated circuits developed by my company and software control system to make the step-up rate is truly uniform, accurate, and be able to accurately measure the leakage current data. Real-time rendering test curve accurate judgment and it can save, analyze and print test data.
-
product
Voltage Probe
VOL-PBE
• EMI Receiver equipped with voltage probe can test disturbance voltage from load terminals or control terminals
-
product
3U VPX 1/10/40 Gigabit Ethernet Switch
ComEth4081e
Powered by a Marvell highly integrated System-on-a-Chip (SoC) with programmable packet processors, and controlled by Switchware, the field-proven Interface Concept network management application, the ComEth4080e offers a high density of 1GbE/10GbE and 40GbE ports on a 3U footprint.
-
product
LXI High Voltage Multiplexer Plugin Module
65-231-902-HI
The 65-231-902-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
PXI 16 Trib Daisy Chain Switch Balanced 96 W
40-796-001
The 40-795/796 Daisy Chain Switching Module is designed for telecom test applications. It allows production or verification testing of SONET/SDH transmission multiplexers switching 2MBit/s or 1.5MBit/s data over 100 or 120 balanced lines.
-
product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass, Single-Mode, 9/125 Fiber, LC Connectors
42-860A-432
The 40/42-860A-432 is a PXI/PXIe triple insert/bypass switch with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
Switching Power Supplies
PeakTech Prüf- und Messtechnik GmbH
A type of power supply that works by switching current into a high-frequency transformer or inductor at frequencies much higher than the input or line frequency
-
product
High Voltage Testers
HV Test, which is also known as Hipot Test – short form of high potential – is used to test the insulation quality of the auxiliary circuit of circuit breakers. The HV Test is useful in finding damaged insulation, stray conductive materials around the conductors, and problems due to terminal spacing and tolerance errors in cables.
-
product
PC Controlled Low Voltage Tester
Cablescan S9
The Cablescan S9, with a 9-board Expansion Cabinet, may be ordered with 1 to 9 low-voltage 128-point scanner boards. Fully loaded with scanner boards, this tester provides 1152 test points.
-
product
Switch Testing Machines
Educated Design & Development, Inc.
1 or 3 actuating device(s) for rocker switches and push- button switches with 2 single-acting pneumatic cylinders each, with air throttle valves to adjust the actuating speed, height-adjustable mounted to holders, with multiple adjustable specimen holders, with safety sockets to connect the specimens to external test voltages and loads1 housing, made of steel, with protective hood1 plug-in unit with front panel for operating the devices.1 Control device for the entire unit:main switch with EMERGENCY OFF function, safety switch for the protective hood, mains cord and fuses1 control device for each actuating device:programmable control unit with exchangeable program modules (containing the "test rhythm") and for adjusting and indicating the test parameters "number of strokes" and "stroke time", start and stop push-buttons, push-buttons for moving manually the cylinder pistons and as actuation indicator for the cylinder
-
product
Close Contact Confirmation Switch
HPS/MHPS/UHPS
High precision needle mechanism enables highly accurate detection such as contact confirmation.In addition, various special nozzles can be applied to various position detections.
-
product
Connect PT100/PT1000 Sensors To Output A Voltage Signal
K- PT100/1000
Our K-PT module is designed to connect up to PT100/PT1000 sensors and simply provides an output voltage signal. Thus enabling the most standard voltage measurement devices to work with PT100/PT1000 sensors. The PT100 sensors offer excellent accuracy and repeatability.
-
product
LXI High Voltage Switching - 4-Bank, 1-Pole, 12:1 Multiplexer Plugin Module
65-231-906
The 65-231-906 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
Rugged Gig-E Switch
RESIU31
NAI's RESIU31 subsystem is configured with NAI's 75D4-H2, a Layer 2+ Gigabit Ethernet Switch built upon NAI's multifunction, 3U cPCI board technology. Ideally suited for rugged military, industrial, and commercial applications, the RESIU31 delivers an off-the-shelf Ethernet switching solution that accelerates deployment of SWaP-optimized systems.
-
product
Dual High Voltage Power Supply Tester
MS 1110
DHVPS Tester is used to test and service the dual high voltage power supply units. High Voltages of range from 4KV to 11KV can be tested.
-
product
Temperature & Pressure Switches
Pressure switches survive shock and vibration during all operating conditions and phases of flight and have been qualified to temperature conditions that exceed RTCA DC-160 requirements. Testing and design that goes above and beyond what is required has helped to make Measure Tech the "go to" manufacture when airlines need a new switch to help improve dispatch reliability.
-
product
Low-leakage Switch Mainframe
E5250A
The Keysight E5250A low-leakage switch mainframe expands a single measurement station, such as the Keysight B1500A, 4155C, or 4156C, to an automated measurement system. Plug-in modules can be configured either as a cross-point matrix for general parametric measurements or as a multiplexer for long-term reliability measurements.
-
product
RF Switch Matrix
Compact, low-insertion-loss, non-reflective microwave switches. USB controlled and powered with optional Ethernet and audio feedback.
-
product
MEMS Optical Switch
FTBx-9160
With its MEMS-based design, EXFO’s FTBx-9160 delivers durable performance in a compact package. Fast switching time and a 1-billion-cycle lifetime expectancy make it the perfect optical switch for demanding manufacturing applications. The FTBx-9160 MEMS Optical Switch is available for singlemode fibers with a choice of 1x2, 1x4,1x8, 1x12, 1x16, 1x24 and 1x32 modules.
-
product
Current, Voltage, Resistance
Solutions for the testing and calibration of current, voltage and resistance are used in industry (laboratories, production, workshops), in calibration service companies and in quality assurance. These instruments are portable and mobile and are particularly notable for their low measurement uncertainty and high scope of operation.
-
product
Multiport Coaxial Switch, DC to 20 GHz, SP4T
87104B
The Keysight 87104B multiport switch improves insertion loss repeatability and isolation, which is necessary for higher performance test systems. The repeatability and reliability of this switch is vital to ATS measurement accuracy and can cut the cost of ownership by reducing calibration cycles and increasing test system up time. The Keysight 87104B terminated multiport switch provides the long life and reliability required for automated test and measurement, signal monitoring, and routing applications. Highly repeatable switching capability is made possible through Keysight's rigorous design and tight manufacturing specifications. Low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy.
