-
-
Product
Semi-Rigid Cable Set, 3.5 Mm (Test Port) To 3.5 Mm
85131D
-
The Keysight 85131D is an 53 cm (21 in) long1 semi-rigid cable set composed of a 3.5 mm female2 to PSC-3.5 mm female connector and a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss of 16 dB or better. Insertion loss is 0.3 * sqrt(f) + 0.2 dB, where f is frequency in GHz, for the test port connector and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability1 of the Keysight 85131D is less than 0.06 dB and phase is 0.16 * f + 0.5, where f is frequency in GHz.
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-340L
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Suitable for low current measurements of terminal feeder.*High sensitivity and least affection from external magnetic field.
-
Product
Dual Surge Current Generator
MIG0624T-K12
-
Designed for testing telecom surge protection devices according to ITU-T K12. The generator has two indepedent impulse outputs which allow testing of two and three terminal protection devices such as gas discharge tubes (GDT). The generator can be configured for two terminal devices or with the outputs in parallel to increase the current impulse for two terminal devices.
-
Product
Conformance Testing
Clarinet-TTCN ATM ETS
-
Protocol: UNI 3.1 ATM Layer Conformance Test Suite for End SystemsIUT: ATM Equipment UNI 3.0ATS: ATM-FORUM standards af-test-0060.000 covers the test of UNI 3.0 ATM Layer of End Systems
-
Product
DDoS Testing
-
DDoS testing missions enable enterprises, operators and governments to test their resilience against DDoS and evaluate their DDoS mitigation infrastructure.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
EBIRST 50-pin D-type To 25-pin D-type Adapter
93-005-414
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Component Test Fixture For N1413 With B2980 Series
N1428A
-
The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.
-
Product
Current Probe Calibration Fixtures
-
Calibration fixtures are used for calibration of Coupling Loss/Transfer Impedance of current probes and BCI probes, as well as for the calibration of test levels for conducted immunity/susceptibility tests using BCI probes.
-
Product
Precision AC/DC Active Current Shunt
2575A
-
A versatile, powerful calibration tool, the 2575A Precision AC-DC Active Current Shunt measures both AC/DC current and works as a standard for low-level resistance calibration requirements.
-
Product
Thermometer Set
94029
-
A complete kit for accurate temperature monitoring in all application areas. Supplied in a rugged carry case with foam insert.
-
Product
AC DC Current and Voltage Converters
-
The DAT5023 I is an AC or DC current converter, the input current range is selectable on order from 0-5Amps, 0-10Amps, 0-20Amps, 0-25Amps, 0-30Amps, 0-40Amps, 0-50Amps, 0-60Amps. It measure the current with the use of a Hall effect transducer. There is a coil (current transformer) inside the current converter which is isolated from the current input. The cable passes through the housing of the converter and the coil and the true root mean square measurement is taken from this coil then converted to a standard industrial signal output.
-
Product
Bluetooth Integrated Flexible Coil Current Meter
-
One of the most advantages of the Flexible Coil Current Meter is external wirelessly connect to Smart phone / Tablet / PC to view data, record reading, capture picture with data on it and send the information to headquarter.
-
Product
Coating Testing
-
Makes it possible to predict their durability and how they will be affected by the passage of time.
-
Product
Leakage Current Monitor
-
To alert utility-line workers of overcurrent conditions on such aerial devices as insulated ladders and truck booms, the Chance Sentinel sounds an alarm if leakage current reaches a pre-set level.
-
Product
Test & Measuring
-
Messung Electrical Engineering
Electronics manufacturing, testing and quality control need test and measuring equipment and ergonomic environments that are flexible, versatile and safe. Hence we bring the future of modern workplace systems for R&D labs, calibration centres, training and didactic centres, electronic assembly & testing, spread across the Indian electronic industry. Our innovative, modular & customised laboratory furniture systems, and intelligent test & measurement solutions are designed to improve efficiency while offering user comfort.
-
Product
EBIRST 200-pin LFH To 96-pin SCSI Adapter Cable
93-002-226
-
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Attribute Testing
-
Critical attribute testing during manual or automated processing is essential to any manufacturing success. Tech Group has developed many testing solutions both standard and custom-made for mainly electronics and mechanical industry. Our modular designs give the advantage to offer short lead-time, cost efficient solutions according to your exact needs.
-
Product
Test Probes
-
A physical device used to connect electronic test equipment to a device under test (DUT).
-
Product
Altitude Testing
-
DATASYST Engineering & Testing Services, Inc.
Altitude testing simulates reduced air pressure experienced at higher elevations and its impact on product integrity. We can perform altitude testing at a constant rate or cycle between altitude pressures while your component is powered on or powered off.
-
Product
Voltage And Current Amplifier
KINGSINE KA30 / KA60
-
KINGSINE Electric Automation Co., Ltd.
KINGSINE's KA30 / KA60 voltage and current amplifier is high accuracy, high power, Panel-mounted type real time simulation power amplifier with four-phase voltage and three-phase current.
-
Product
Load Testing
-
Load Testing, Simplified. We sort out the infrastructure, so you can spend more time testing. Tool Agnostic - We support JMeter, Gatling, Capybara and Selenium. Unfettered Testing - No limits on how you test, run as many users for as many tests, for as long as you like. Third-party Integration - Send results to Slack, Hipchat, Flowdock, or your own services using our API.
-
Product
Test Solutions
AT/CX/CM Series
-
The VeEX AT/CX/CM series are next generation test solutions designed for analog and digital cable TV networks supporting VoIP, WiFi, and Internet service. Analog and Digital SLM, ingress noise sweep, deep interleave support, and QAM constellation analysis are among many standard features. Enhanced optional features include QAM16/64/128 Upstream Generation (USG), Reverse Path QAM Analysis, and DOCSIS 2.0/DOCSIS 3.0 Cable Modem emulation. A high capacity LiIon battery pack provides extended autonomy for a full day use with only a single charge.
-
Product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-20MH
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement for solar power system*Least affection from the magnetization of core and temperature fluctuation*DC leakage current measurements*Convenient ＋5V single polarity power supply
-
Product
Logger with Current Clamp0 to 200A AC
TV-4810
-
As well as recording data the unit has a display that shows what the unit is currently reading. The unit has an IP65 case and features high reading resolution and accuracy, a large memory, a fast offload speed and a low battery monitor.
-
Product
Compliance Test, Development and Test Service
DinoStor
-
With its focus on solving critical backup problems associated with Network-Attached Storage (NAS), DinoStor delivers a broad range of products and services to benefit users and vendors of NAS solutions.
-
Product
Fused Test Probes with Silicone Test Leads
AL-57FL
-
Standard Electric Works Co., Ltd
● AL-57FL is an ideal tool which shows the indication of live voltage even with blown fuse.● 2 replaceable fast-acting fuses are built-in. The specs of the fuses are 1000V, 11A with internal rating of 20kA AC/DC.● Provide additional testing protection.● Help to prevent a possible mis-indication when there is voltage present.● CAT III 1000V, CAT IV 600V, 10A with protective cover.● 2mm probe tips, removable 4mm brass caged banana probe tips are also included.● Include High-quality silicone test leads, 1.5 meter long.● Wipe the fused test probes and silicone test leads periodically with a damp cloth and detergent. Do not use abrasives or solvents.● Operating temperature: -20 °C to +50 °C (-5 °F to 120 °F)● One year warranty● Can't be used on current mode with blown fuse.● Rating : EN 61010-031 CAT Ⅲ 1kV 10A / CAT Ⅳ 600V 10A
-
Product
Automatic Transformer Tester
SS3250 / SS3252 / SS3302
-
Automatic transformer test instrument is a precision test system, designed for transformer production line or incoming/outgoing inspection in quality control process, with high stability and high reliability. With the enhanced capability in turn ratio measurement, they can solve the measuring problems of low coupling coefficient, transformer's turn ratio and turn number with more precise measurement.
-
Product
HCAI-1 High Current Arc Ignition Tester
HCAI-1
-
The HCAI-1 High Current Arc Ignition Tester is according to IEC 60950-1:2001, BS EN 60950-1:2001, BS 7002:2000, GB 4943.1-2011
and UL746A, IEC60947.1: 1999, GB/T14048.1-2000, IEC730.1:1993, GB14536.1-2008 and other standards required simulated safety test project. Parts and components of insulating materials or other solid combustible materials that are prone to flame spread in electrical and electronic equipment may ignite due to proximity or contact with electric arc, causing electrical fire and endangering the reliable operation of equipment and personal safety.
