-
Product
VME & CPCI Systems
-
Verotec has a selection of configured systems plus individual elements such as backplanes, power supplies and cooling products, compliant with the PICMG / VITA specifications, and supported by a range of accessories. We offer these in standard VME and CompactPCI platforms across various mechanical form factors with customising options to suit specific applications.
-
Product
Combined Environmental Reliability Test System
VTC SERIES
-
HALT/HASS testing challenges the design, components, sub-assemblies and final assemblies of today's manufactured products. Stresses are applied through a number of conditions to set operational limits and ultimately precipitate failure in the HALT/HASS test environment. Rapid thermal change rate is one of the classic conditions that facilitate product stress.VTC Series chambers are equipped with an LN2 cooling system, with modulating valve and directed air flow to the product, provides the rapid thermal change rates required to achieve maximum product stress. Additionally, these rates are accomplished with smaller space requirements, lower audible noise, no water requirement, and lower maintenance costs than a typical refrigeration system.
-
Product
High Impact Shock Test System
KRD16 series
-
High impact shock test system meets MIL-S-901D standard which covers shock testing requirements for ship board machinery, equipment, systems, and structures, excluding submarine pressure hull penetrations. The purpose of these requirements is to verify the ability of shipboard installations to withstand shock loadings which may be incurred during wartime service due to the effects of nuclear or conventional weapons.
-
Product
Total Tank Level System
-
The Total Tank Level System is an intrinsically safe and explosion proof level sensor with several communication options. Outputs include Modbus RTU digital, dual 4-20mA and HART. The Modbus version is offered in a single housing and the 4-20mA and HART output product features a dual compartment housing and display.
-
Product
Controls Systems for Engine Control and Combustion Analysis
NI Powertrain
-
NI Powertrain Controls systems incorporate the LabVIEW reconfigurable I/O (RIO) architecture to create some of the world’s most flexible and capable combustion analysis and engine control systems. The engine control systems can drive both solenoid and piezoelectric direct injectors, control timing events with 25 ns of precision, and implement novel engine control strategies such as next- and same-cycle control. The combustion analysis systems are available in both portable and higher performance stationary form factors.
-
Product
Burn-in Systems
-
Incal Offers A Line Of State-Of-The-Art Burn-In Testing Hardware And Software For Retrofit And/Or Total, Customized Burn-In System Configurations.
-
Product
Gas Detection System
TOC-625 MICRO
-
International Gas Detectors Ltd
For small systems up to 8 devices with simple I/O requirements this system is ideal. The TOC-625 Micro Gas Detection System Controller interfaces with existing TOC-30A addressable gas detectors and has auto detect and set up features making deployment fast and easy for installers not used to gas detection systems.
-
Product
Pulsed-DC Systems
-
Extend process innovation with Advanced Energy’s comprehensive pulsed-DC suite. Minimize arcing, enhance deposition rate, improve film flatness and packing density.
-
Product
Wafer and Cells PL System
HS-PL
-
Photoluminescence (PL) Imaging is a unique non-invasive inspection tool as it can be used in-line at many different steps of the cell manufacturing process. This facilitates the direct comparison of data obtained at one process step to data obtained at another. Additionally, PL imaging can be compared to electroluminescence (EL) imaging on finished cells using comparable equipment.
-
Product
Modular Test System
-
A modular test system, RTS (real time scanner) provides instant test results with minimal interface cables to check wiring during installation.It tests wire harnesses in real time using our micro switching technology, reducing the need for high cost interface cables by around 90%. an innovative best-in-class solution for FAL testing, RTS also offers many benefits for wire harness and sub-assembly manufacturers.
-
Product
Preparative HPLC System Configurations
LC-4000 Series
-
Three Platform Options: Up to 20 mL/min for columns up to 21.2 mm ID, Up to 50 mL/min for columns up to 30 mm ID, Up to 120 mL/min for columns up to 50 mm ID.
-
Product
Fiber Optic Crank Angle Measurement System
CP-5730/CP-0610/CA-6000B
-
CP / CA series are systems that detect the rotation angle of the engine crankshaft composed of CP-5730 Fiber Optic Crank Angle Detector, CA-6000B Crank Angle Amplifier and CP-0610 Rotation stop jig.
-
Product
E-mobility Test Systems
-
Correct contactingcharging cable detectionsecurity questionExtensive range of accessories for on-site measurements in a separate caseCharging cable with additional measuring lines (Sense)Convenient control through guided test procedure via WinSAM and tabletElectromechanical locking
-
Product
CPE Design Verification System
Jupiter 310
-
Jupiter is the industry standard for automated DOCSIS physical (PHY) layer testing. It provides the most comprehensive test coverage and accurate results on the market for DOCSIS 3.1 devices.
-
Product
CorSys Longevity: Rackmount PC Systems
-
Corvalent’s Longevity brand of industrial rackmount workstations come pre-configured with our proprietary long-life industrial motherboards. These rackmount systems are designed for mission-critical and industrial IoT applications in various industries, including medical technology, defense, industrial automation, energy, and security and surveillance.CorSys Longevity Systems are available in 2U, 3U, and 4U sizes:-CorSys Longevity 248i 20” 2U Rackmount Workstation-CorSys Longevity 348i 20.7” 3U Rackmount Workstation-CorSys Longevity 448i 20.1” 4U Rackmount Workstation
-
Product
PXI based Test Systems Module
PXI XJLink2
-
The PXI XJLink2 module allows the integration of XJTAG into PXI-based test systems. PXI XJLink2 has one JTAG controller that can be connected to up to 4 JTAG chains, which are configurable for pinout and voltage. It is easily integrated with LabVIEWTM with a full set of Virtual Instruments (VIs) included.
-
Product
Primary Injection Test Systems
-
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
Product
Live-Cell Analysis System
-
Analyze your cells for days, weeks or even months as they sit stationary in the stable environment of your tissue culture incubator.
-
Product
Vehicle Tracking System
-
Information System Technologies Inc.
ISTI has built a vehicle tracking system that overcomes the challenges with acoustic tracking and localization of small ground and airborne vehicles using low-cost wireless sensor nodes. The sensor-level sub-band feature extraction and streaming of the encoded data enables real-time direction of arrival (DoA) estimation and tracking even for large wireless sensor networks with limited bandwidth. Benefits include: accurate tracking of single or multiple closely spaced electric or gas driven small planes and UAVs, collaborative decision-making, target localization and classification, robustness to sensor node loss, flexibility and deployment ease. The interface gives users complete control over the entire sensor network, including the ability to monitor the azimuth and elevation angles to the targets in real-time.
-
Product
Test System Robotics
-
With the ever increasing need to provide a fast return on investment of your test solution investment, robot's are becoming more widely accepted as a means of reducing your testing costs. Not only can they be programmed for fast product test, they don't have the normal issues associated with human capital.
-
Product
AIR AI Inference Systems
-
Advantech AIR Series Edge AI Inference Systems offer a variety of CPU/NPU options and integrate AI capabilities seamlessly for various applications.
-
Product
Data Acquisition System - 3U 1-Slot
DAQ-31CP0G
-
The DAQ-31CP0G is a preconfigured rugged system with a high-performance, low power ARM® Cortex®-A9 processor. It is ideally suited to support a multitude of data acquisition applications that require high-density, multichannel, programmable communications consisting of: ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939) and Dual-Port Gig-E Ethernet.
-
Product
Microphone System
378B02
-
This model includes a 1/2" microphone cartridge, a mated preamplifier with TEDS, and system calibration.
-
Product
Cameras & Imaging Systems
-
Cameras & Imaging Systems by TP - Thermal Imaging, Corona Cameras
-
Product
PXI System Synchronization Modules
-
Keysight's PXIe System Synchronization Module (SSM) provide multi-module/multi-chassis synchronization and triggering for Keysight’s modular systems, as well as other Keysight instruments. They meets the STM specifications documented in the PXI Express Hardware Specification.
-
Product
Custom X-FROG Systems
X-FROG Scan
-
Because of the design changes in our FROG Scan system, we can customize the FROG Scan systems to your needs to create X-FROG systems where you supply a reference pulse and a pulse to be measured. Please contact us for your needs.
-
Product
Solder Paste Inspection System
KY8030-3
-
The new KY8030-3 delivers 3x fasterinspection without compromisingperformance and accuracy.Using patented dual projection,the system eliminates the criticalShadow problem that all 3D SPI systemscan be vulnerable to.Additionally, the new KY8030-3 has solvedthe PCB Warp problem that seriouslyimpacts inspection accuracyand reliability of result.
-
Product
Development System
FE-5131
-
Emulates AT89C5131/AT89C5131A Derivatives with 6/12 Clocks/Cycle31K Code MemorySoftware TraceReal-Time EmulationFrequency up to 40MHzMS-Windows Debugger for C and AssemblerKeil Vision2 Debugger CompatiblePLCC, SOIC, QFP and 32-QFN Emulation HeadersSerially Linked to PC at 115Kbaud
-
Product
Capture & Replay System
-
PacketStorm Communications, Inc.
The PacketStorm CRS is a packet capture and replay system with hardware time stamping at 10Gbps. The user specifies which packets to capture based on the filter parameters. Packet captures can be continuous or stop capture after a certain number of frames, bytes, or time. The 10G filters include: Source Address, Destination Address, Source Port, Destination Port, and Protocol. The CRS file management includes automatic file compression and decompression. Operation is via the console or the remote GUI. There are two CRS versions: 1U and Lunchbox. The 1U version is intended to be installed in a rack or on a test bench. The lunchbox version includes a keyboard, mouse, and monitor and is intended to be moved about between stations and labs.
-
Product
Test Automation Platform Developer's System
KS8400A
-
The Keysight KS8400A Test Automation Platform (TAP) Developer's System provides powerful, flexible and extensible test sequence and test plan creation with additional capabilities that optimize your test software development and overall performance. Keysight TAP is a modern Microsoft .NET-based application that can be used stand-alone or in combination with higher-level test executive software environments. Leveraging C# and the power of Microsoft Visual Studio, TAP is not just another programming language. It's a platform upon which you can build your test solutions, maximizing your team's productivity by using your existing software development tools and infrastructure.
