-
product
Synchro to Digital-Resolver to Digital Converters
HRDCK-HSDCK
Computer Conversions Corporation
HSDCK and HRDCK series are the highest accuracy, miniature tracking synchro and resolver to digital converters in the marketplace. They are designed specifically for ultra precise requirements in the most demanding industrial and military applications.
-
product
PXI-6713, 12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
777795-01
12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6713 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6713 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
product
8-CH 24-Bit High-Resolution Dynamic Signal Acquisition Module
PCIe-9529
The ADLINK PCIe/PXIe-9529 is a high-performance, high density, 8-CH analog input dynamic signal acquisition module. The PCIe/PXIe-9529 features eight 24-bit simultaneously sampling analog input channels. The 24-bit sigma-delta ADC provides a sampling rate of 192 kS/s at high resolution, making it ideal for higher dynamic range signal measurement. All channels are sampled simultaneously and accept input range up to ±10V, and the analog inputs support software-selectable AC or DC coupling and 4 mA bias current for integrated electronic piezoelectric (IEPE) sensors. The module is especially designed to meet the requirements of vibration analysis and audio testing.
-
product
500 Watt DC/DC Converter, 3U VPX, VITA 86 High Altitude
VPX57C
NAI's VPX57C is a rugged and high-performance 500-Watt Output +270 VDC Input 3U VPX DC/DC converter designed for aerospace, defense, and industrial markets. It is an off-the-shelf power supply ideal for high altitude operations such as orbit launch vehicles or Fighter-Grade applications that plugs directly into a standard VPX conduction cooled chassis utilizing a VITA 86 connector. The power supply, engineered to meet extremely harsh environmental conditions, features continuous Background Built-In-Test (BIT), I2C communication, remote error sensing, and protection against Input transients, over-voltage, over-current, and short-circuits, ensuring reliable and consistent performance.
-
product
32-CH Isolated DI & 32-CH Isolated DO PCIe Card with High Input Range
PCIe-7432
ADLINK PCIe-7432 is a 32CH Isolated DI & 32CH Isolated DO PCIe Card, featuring robust 2,500V isolation protection, suitable for most industrial applications. Input range up to 24V makes it easy to acquire status of external devices (PCIe-7432HIR output range is from 5 to 35V), making it suitable for relay driving and industrial automation applications. Also provided are two easily configurable interrupt sources on digital input channels.
-
product
Synchro to Digital-Resolver to Digital Converters
MSI MRI MX
Computer Conversions Corporation
Computer Conversions MX Series are low cost multiplexed synchro or resolver to digital converter sets designed for Military or Industrial diagnostic and control applicatioms requiring 3-128 axis per control.
-
product
Optical-Electrical Converter - MATRIQ
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
product
1000 Watt AC/DC Power Converter, 6U VPX
VPX56H-6
The VPX56H-6 is NAI's latest high power, 1000 Watt AC/DC converter which accepts either a 3Ø 115VAC L-N inputs or a +270 VDC input. It plugs directly into a standard 6U VPX chassis with a (VITA 62) 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
product
NI-9218, 51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module
783362-01
51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module - The NI‑9218 is designed for multipurpose measurements. It offers built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. Each channel is individually selectable, so you can perform different measurements on each channel. The NI‑9218 is ideal for creating universal test systems for automotive, off-highway, and data-logging systems.
-
product
Analog Output PXI Card
GX1642
The GX1642 is a 3U PXI digital to analog output board is designed specifically for applications where multiple analog outputs are required. The GX1642 offers precision signal sourcing performance and quality at an economical price.
-
product
Synchro to Digital-Resolver to Digital Converters
SDT RDT
Computer Conversions Corporation
The SDT/RDT Series, are single module, tracking, Multi-speed synchro/resolver to digital converters designed for Military and Industrial Applications. They will accept Electrical Multi-speed, or Geared (dual speed) Multi-turn; Synchro or Resolver input sets (Fine/ Coarse), having the most standard ratio’s, and convert them into a single non-ambiguous 16 Bit data word with up to +/-20 arc. seconds accuracy.
-
product
400 Watt DC/DC Converter, 3U VPX, Holdup Time
VPX68
NAI's VPX68 is a rugged and high-efficiency 400-Watt Output +28 VDC Input 3U VPX DC/DC converter designed for aerospace, defense, and industrial markets. It is an off-the-shelf power supply with optional integrated Holdup Time that plugs directly into a standard VITA 62 conduction cooled chassis. The power supply, engineered to meet harsh environmental conditions, includes continuous Background Built-In-Test (BIT), I2C communication, remote error sensing, and protection against Input transients, over-voltage, over-current, and short-circuits, ensuring reliable and consistent performance.
-
product
Digital to Synchro and Digital to Resolver Converters
Computer Conversions Corporation
1.2VA, 1.5VA, 4.5VA and 5VA Models60 or 400, & 60 and 400 Hz. Models to 22 KHz.Trouble Free Isolated Reference Inputs & Signal OutputsUltra High Efficiency, Low DistortionSelf Powered off the AC Reference Input (DSP Series)Internal Cool AC-Pulsating Supplies (DSP Series)Very Low Loss & Heat DissipationFULLY INTEGRATED, NO EXTERNAL COMPONENTS REQUIREDVery High Resistance to Shock and VibrationHigh Reliability Throughout ImplementationIsolated, Transient, Therrnally & Short Circuit Protected Outputs
-
product
PXIe-4303 , 24-Bit, 32-Channel, 51.2 kS/s, ±10 V PXI Analog Input Module
783866-01
24-Bit, 32-Channel, 51.2 kS/s, ±10 V PXI Analog Input Module—The PXIe‑4303 is a filtered input module for voltage, thermocouple, and current measurements. The module offers you the ability to select a digital filter per channel to provide extra filtering performance. You also can operate up to four different sample rates and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI‑DAQmx driver simplifies hardware configuration and measurement.
-
product
PXI/PXIe Analog Output/Current Loop Simulator Module - 4 Channel
43-765-004
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
600-Watt DC/DC Converter, 6U VME
64PS1
The 64PS1 is a 600 Watt DC/DC Converter that plugs into a 6U VME chassis with an 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This switching power supply accepts a +28 VDC input and provides a single output at 600 Watts continuous or 1,000 Watts peak.
-
product
Synchro to Digital-Resolver to Digital Converters
SACP-RACP
Computer Conversions Corporation
Computer Conversions Synchro-Resolver to ACP/ARP Converters accept choice of synchro-resolver input options, power input, and mounting configuration, converts synchro/resolver input into ACP (Azimuth Change Pulse) and ARP(Azimuth Reference Pulse) type outputs suitable for 75 ohm drive.
-
product
AC-DC Rectifier / Converters
These following AC-DC converters all can provide 3.3/5/9/12/25/24/28/48V etc output. Newly acquired 2U rack mount 48V rectifier is a mature solution for 48V telecom systems.
-
product
Synchro to Digital-Resolver to Digital Converters
HSDC-HRDC
Computer Conversions Corporation
HSDC & HRDC Series are Miniature, Tracking Synchro and Resolver to Digital Converters with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command for military and industrial applications.
-
product
Multi-Function PXI Card
GX3788
The GX3788 is a user configurable, FPGA-based, 3U PXI multi-function card which supports digital and analog test capabilities. The card employs the Altera Stratix III FPGA which features over 45,000 logic elements and 1.836 Kb of memory. The GX3788 is based on the GX3700 FPGA card and includes an integral daughter board which provides (8) differential input, 16-bit, 250 MS/s A to D converters and (8), 16-bit, 1 MS/s, D to A converters. The module's FPGA is pre-programmed, providing access to all digital and analog functions. Alternatively, users can program or modify the FPGA , allowing user to adapt the module to their own specific test needs. The design of the FPGA is done by using Altera's free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded into the FPGA directly or via an on-board EEPROM.
-
product
sbRIO-9218, Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module
783362-02
Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module - The sbRIO‑9218 helps you perform multipurpose testing. With the sbRIO‑9218, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors. You also can use the sbRIO‑9218 to perform quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. You can individually select and perform a different measurement type on each channel. Additionally, the sbRIO‑9218 features 60 VDC analog input isolation. Non-enclosed modules are designed for OEM applications.
-
product
Digital to Synchro-Digital to Resolver Converters
ST-DRL ST-DSL ST Prefix
Computer Conversions Corporation
Terminations subject to converter module features where applicable.Plastic backplane mount track included, or may be mounted using spacers at mounting hole locations.
-
product
100-Watt DC/DC Converter
55LS1
NAI’s 55LS1 is a COTS, 100 Watt DC/DC Converter that accepts a +28 VDC input and provides a single full-power output at a baseplate temperature of +100° C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
product
PXIe-4302, 24-Bit, 32-Channel, 5 kS/s, ±10 V PXI Analog Input Module
783865-01
24-Bit, 32-Channel, 5 kS/s, ±10 V PXI Analog Input Module—The PXIe‑4302 is a filtered input module for voltage, thermocouple, and current measurements. The module has an A/D converter per channel to enable a simultaneous sample rate of 5 kS/s. The PXIe‑4302 offers you the ability to select a digital filter per channel to provide extra filtering performance. You also can operate up to four different sample rates and triggering configurations concurrently to ensure you measure every sensor as needed. The included NI‑DAQmx driver simplifies hardware configuration and measurement.
-
product
PXIe-4464, 204.8 kS/s, 119 dB, 6 Gains, AC/DC-Coupled, 4-Input PXI Sound and Vibration Module
783087-02
204.8 kS/s, 119 dB, 6 Gains, AC/DC-Coupled, 4-Input PXI Sound and Vibration Module—The PXI‑4464 delivers simultaneous sampling on all channels. In addition, the PXI‑4464 includes built-in antialiasing filters that automatically adjust to your sampling rate, six software-selectable input gains ranges, and TEDS smart sensor support for error-free setup. The IEPE excitation circuit can deliver current for high-power sensors and strong data integrity over long sensor cable runs.
-
product
50-Watt DC/DC Converter; Dual Output
55JD1
NAI’s 55JD1 is a 50-Watt DC/DC Converter that accepts a +28 VDC input. This COTS unit provides full-power output, dual at a baseplate temperature of +100° C.
-
product
16-CH Latching Relay Outputs & 16-CH Isolated DI Card
PCI-7256
- Supports a 32-bit 3.3 V or 5 V PCI bus- 16-CH latching SPDT relay outputs- Power saving on relay actuation- Output status unchanged when power-off- On-board LED indicators for relay status
-
product
PXIe-4330, 25 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module
781346-01
25 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module—The PXIe‑4330 is a simultaneous input module that provides integrated data acquisition and signal conditioning for bridge-based sensors. The PXIe‑4330 includes increased accuracy, high data throughput, and synchronization features, making it ideal for high-density measurement systems. To remove noise, the PXIe‑4330 offers antialiasing and digital filters per channel. Each channel also features an independent, programmable excitation voltage. Additionally, the PXIe‑4330 provides remote sensing, internal bridge completion, and shunt calibration options per channel.
-
product
NI-9218, 51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module
783367-01
51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module - The NI‑9218 is designed for multipurpose measurements. It offers built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. Each channel is individually selectable, so you can perform different measurements on each channel. The NI‑9218 is ideal for creating universal test systems for automotive, off-highway, and data-logging systems.
