-
Product
Dual-Axis Accelerometer For HS3/4/4-DIFF Handyscopes, +/- 5G
TP-ACC50-25
-
The Accelerometer is a low cost, low power, complete dual-axis accelerometer with signal conditioned voltage outputs. The output signals are analog voltage proportional to acceleration. The Accelerometer is capable of measuring both positive and negative accelerations to at least �+/- 5G.
-
Product
IEPE Triaxial Accelerometer – 1000 mV/g
HDP356B18
-
Triaxial accelerometer high sensitivity, ICP, 1V/g, weight 25g, range 5 g pk
-
-
Product
ICP Blast Pressure Pencil Probe
Model: 137B21B
-
Quartz, free-field, ICP blast pressure pencil probe, 1000 psi, 1 mV/psi, BNC connector
-
Product
SparkFun Triple Axis Accelerometer Breakout
ADXL345
-
This new version adds two standoff holes as well as an extra decoupling capacitor. The ADXL345 is a small, thin, low power, 3-axis MEMS accelerometer with high resolution (13-bit) measurement at up to +-16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface.
-
Product
ICP Microphone System
HT378B02
-
This model includes a 1/2" microphone cartridge, a mated preamplifier with TEDS, and system calibration. Click the following for individual component information.
-
Product
In-line ICP® Charge Converters
-
In-line ICP® charge converters play a vital role in converting high impedance charge mode piezoelectric sensor signals into low impedance voltage signals, facilitating input to readout, recording, and analysis instruments. Specifically engineered for compatibility with high temperature piezoelectric sensors, these units are capable of operation in environments reaching up to 500°F (260°C). The series boasts ±2.5V or ±5.0 V output, offering a range of gain options, all packaged within a compact and durable casing. As a cost-effective alternative to laboratory charge amplifiers, in-line ICP® charge converters present an appealing choice for multi-channel applications.
-
Product
High-Sensitivity Tri-Axial Accelerometer with Built-In Preamplifier
NP-7310
-
NP-7310 is the accelerometer with built-in preamplifier, and capable of tri–axial directions simultaneous measurement. It is suitable for the low frequency vibration measurement such as ground vibration or floor vibration while operating the machine. NP-7310 can be used with the sensor amplifier unit such as AU-2100, AU-2300 or PS-1300. Also, it is possible to input directly to the analyzer or recorder which the constant current amplifier is built-in such as the FFT Analyzer of DS-2000 series, DS-3000 series, CF-7200A, CF-9000 series or CF-3650/3850 series.
-
Product
IEPE Triaxial High Sensitivity Accelerometer 10V/g
HDBV-1000
-
HDBV-1000 is a tri-axial accelerometer for the measurement of human exposure to whole-body vibrations, according to ISO 2631 and ISO 8041.
-
Product
SparkFun Triple Axis Accelerometer Breakout
ADXL377
-
The ADXL377 is a small, thin, low power, complete 3-axis accelerometer with signal conditioned analog voltage outputs that has a full-scale range of ±200g for measuring more extreme changes in motion, shock or vibration. This board has broken out all the pins you’ll need to get the necessary data from the accelerometers. The breakout is perfect for applications like concussion and head trauma detection or high force event detection.
-
Product
SparkFun Triple Axis Accelerometer Breakout
KX134 (Qwiic)
-
This SparkFun Triple-Axis Accelerometer Breakout is a simple Qwiic breakout for the KX134 digital accelerometer from Kionix. The KX134 is a low-power, 16-bit resolution three-axis accelerometer capable of measuring ±8g/16g/32g/64g (user-selectable) and has up to a 10kHz output data rate making it ideal for high-g measurements as well as high-speed applications such as vibration sensing.
-
Product
SparkFun Triple Axis Digital Accelerometer Breakout
ADXL313 (Qwiic)
-
The SparkFun ADXL313 Breakout is a low power, high resolution (up to 13-bits) 3-axis accelerometer for measurement up to ±4g. This breakout measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Digital output data is formatted as 16-bit two's complement and is accessible through the on-board Qwiic connectors (I2C) or SPI.
-
Product
Accelerometers
-
Dytran accelerometers are used for product testing & development, structural monitoring, and industrial machinery health monitoring management. We offer a wide range of piezoelectric & VC MEMS sensors.
-
Product
MEMSIC 2125 Dual-axis Accelerometer
28017
-
The MEMSIC 2125 is a low cost, dual-axis thermal accelerometer capable of measuring tilt, acceleration, rotation, and vibration with a range of ±3 g. For integration into existing applications, the MEMSIC 2125 is electrically compatible with other popular accelerometers. MEMSIC provides the 2125 in a surface-mount format. Parallax mounts the circuit on a small PCB, providing all I/O connections so it can easily be inserted on a breadboard or through-hole prototype area.
-
Product
Triaxial Wireless Accelerometer
-
Our Triaxial Wireless Accelerometer is a vibration sensor specially designed for vibration analysis with universal compatibility. WiSER 3x is a wifi accelerometer that sends 3 axis vibration data + 1 additional channel simultaneously to any data collector in the market. Also, WiSER 3x is a wireless ultra-low noise accelerometer with 15 kHz bandwidth that exceeds the characteristics above all of most conventional accelerometers.
-
Product
PCB IMID01, 100 mV/g, IEPE, 2-Pin, Accelerometer, Industrial Vibration Sensor
784175-01
-
The PCB IMID01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. The PCB IMID01 features a sensitivity range of 100 mV/g and uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The sensor supports the IMI Industrial Accelerometer Cable as well as the MIL2M-Breakout Cable.
-
Product
ICP Electret Surface Microphone
130B40
-
Low-profile surface pressure microphone and preamp, prepolarized
-
Product
1-axis Accelerometer GF1
-
Panasonic Industrial Devices Sales Company of America
Acceleration sensor
-
Product
MEMS DC Response Accelerometers
-
PCB® series 3711F, 3713F, 3741F, and 3743F MEMS DC response sensors are used to measure low frequency motion down to zero hertz. These accelerometers are used in applications such as structural monitoring, aerospace vibration testing, drivability, and gravitational force measurements. Each series includes a full scale measurement range from ± 2g to ± 200g and features low spectral noise with high resolution.
-
Product
Servo type Accelerometer
-
A motion is sensed by a displacement detector, a current is fed to the coil to get back the pendulum mass to the original position. This current will be proportional to the acceleration, that is converted to an output voltage. The Servo type accelerometer is for the Earthquake Monitoring or measurements of micro tremor on the Civil Engineering Structures because of its higher sensitivity and stability or more accurate phase responses in the lower frequency range than those of other vibration transducers.
-
Product
Fiber Optic Accelerometer
MR660
-
The MR660 Series Accelerometer provides an innovative solution to measure vibration and movement in high voltage or ATEX environments. The MR660 Accelerometer system employs a highly sensitive MEMS membrane to provide a robust system capable of producing an output signal of 100mV/g pk-pk.
-
Product
ICP Plasma System
-
The AXIC IsoLok® Inductively Coupled Plasma (ICP) Load-Locked Processing System from AXIC, Inc. defines a new concept in Deep Reactive Ion Etch (DRIE) and low temperature-low damage Plasma Enhanced Chemical Vapor Deposition (ICP-PECVD) plasma processing. The system is based on a modular design starting with a universal chamber and cabinet unit with ICP etch or deposition bottom electrodes available for easy installation into the chamber unit combined with a load-lock. We are confident you will find the ease of use, variety of plasma processes, serviceability and attractive pricing unsurpassed by any other plasma product in the market.
-
Product
General-purpose Accelerometer
MTN/1100
-
General-purpose accelerometer with isolated AC outputs, ideal for vibration analsis and for use in harsh environments.
-
Product
ICP Electret Array Microphone
130A23
-
Nominal Microphone Diameter: 1/4" Frequency Response Characteristic (at 0 incidence)Free-FieldInherent Noise (A Weighted)<30 dB(A) re 20 Pa<30 dB(A) re 20 Pa Dynamic Range (High)150Environmental Temperature Range ( Temperature Effect on Output (-10 to +50 C)<0.7 dB<0.7 dB[2] Influence of Axial Vibration Excitation Voltage 18 to 30 VDC18 to 30 VDC
-
Product
Bluetooth Vibration Sensors / Bluetooth Accelerometers
-
A Bluetooth Vibration Sensor is an Accelerometer capable of recording vibration data and transfer it to a receiver using Bluetooth standard protocol. These sensors usually integrate an accelerometer and a bluetooth transmitter to establish wireless connectivity. Hence having the capability to connect via peer to peer or mesh network.
-
Product
SparkFun Triple Axis Accelerometer Breakout
MMA8452Q
-
This breakout board makes it easy to use the tiny MMA8452Q accelerometer in your project. The MMA8452Q is a smart low-power, three-axis, capacitive MEMS accelerometer with 12 bits of resolution. This accelerometer is packed with embedded functions with flexible user programmable options, configurable to two interrupt pins. Embedded interrupt functions allow for overall power savings relieving the host processor from continuously polling data.
-
Product
PCB IMIB01, 100 mV/g, IEPE, 15 kHz, 2-Pin, Accelerometer, Industrial Vibration Sensor
784176-01
-
The PCB IMIB01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound
-
Product
Accelerometer
BC 201
-
The BC 201 acceleration meters are capacitive acceleration meters and can be used as linear acceleration and position sensors since they measure not only the variable component of the acceleration signal, but the direct component as well.
-
Product
Accelerometer & Platform Test Bench
mS 1115
-
Platform Test Bench used to test the Digital Inputs, Accelerometer Count Reading, High and Low Gyro Torque control of Platform. It also performs Real Time Test for single negative pulse, checks Roll Axis, Pitch Axis, Azimuth Axis. Software package is available to test the Accelerometer.
-
Product
Digital Accelerometer
ZET 7152-N Pro
-
Digital accelerometer ZET 7152-N Pro is intended for recording of vibrational acceleration and is used as a component of stationary vibration monitoring systems used in technological and industrial spheres of application.
