-
Product
DG I/O Backplane Extender Board
9286-1015
-
15" x 15" Backplane Adapter. Not to be used in production environment. Used with any I/O bus adapter during installation of Hawk system. Presents Nova/Eclipse bus signals on dual 50-pin connectors. Two 10 ft. (3 m) ribbon cables included.
-
Product
RS232 Extender via One CAT5e/6 up to 3,935 Feet
ST-C5RS-LC
-
The XTENDEX® RS232 Extender extends one RS232 serial device up to 3,935 feet over a single CAT5e/6/7 cable.
-
-
Product
Uncommitted Extender
UEC220-6U
-
VECTOR Electronics and Technology, Inc.
Two Uncommitted Extenders UEC220-3U attached on top & bottom with mending plate to create UEC220-6U Extender
-
Product
Femtosecond Extended Spectroscopic Systems
Harpia
-
Capabilities of HARPIA‑TA spectrometer can be further expanded by HARPIA‑TF and HARPIA‑TB extensions. Fundamentally, the all-integrated HARPIA system can be viewed as a miniaturized lab facilitating all the most popular time-resolved spectroscopy experiments in a single package. The all-inclusive HARPIA system can provide an extensive comprehension of the intricate photophysical and photochemical properties of the investigated samples.
-
Product
PCIe to 3U VPX Extender / Riser Card
-
This adapter can be used to run, test or program a 3U VPX card in a standard PC PCIe slot. SSC switchable (ON/OFF) PCs available from PCI-Systems Inc.
-
Product
PCI Extender Card for cPCI Systems
DP-cPCI-7497
-
The DP-cPCI-7497 is highly flexible PCI Extender card, which can be used to extend PCI / PCI-X bus from one system to another system over an optical fiber medium upto 500m distance. A PCI-X to PCI-e Bridge is used to convert the PCI / PCI-X protocol to x4 PCI Express protocol operating at 2.5Gbps.The PCI-X to PCI-e Bridge is connected to four optical transceivers (x4 PCI- e link) which can transmit optical signals upto 2.5Gbps speed.A x4 copper medium connection option in lieu of optical transceivers is also available.
-
Product
VME Test Extender 6U/400mm J1/J2
111EXT6140-012X
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Contact Time Extender
CTX
-
The CTX relays supply a 1.5 to 2.5 seconds of a contact output time extension for a momentary contact input. The CTX allows slower device such as scada systems and annunciators to operate thus preventing data loss on the action of protective relays/devices or trip indicators such as the E-Max Trip indication Relay (TIR).
-
Product
Rack Extender Kit, 9025TR, 1.5" Deep
310113494
-
The Rack Mount Extender Block Kit is used for mounting to racks with recessed mounting rails recessed more than 1.” It is made of aluminum with a black anodized finish. NOTE: Used only with slide mounted 9025TR Receivers.
-
Product
Extended Battery Banks
-
Falcon Electric’s extended battery banks provide extra battery runtimes from minutes to hours with our SSG and SSG-RP online industrial UPS systems. The rackmount banks are easily daisy-chained with DC plug-and-play connectors. Simply determine your application requirements and select one of these battery bank options.
-
Product
Range Extender
-
By placing the remote control antennas in a better location, closer to the drone, it is possible to extend the range of the drone.
-
Product
Spectrum Analyzer Extenders
-
RPG's Spectrum Ananlyzer Extenders allow high performance broad-band down-conversion and frequency extension of microwave spectrum analyzers into the THz range.
-
Product
Rack Extender Kit, G12, 2.5" Deep
310113548
-
The Rack Mount Extender Block Kit is used for mounting to racks with recessed mounting rails recessed more than 1”. It is made of aluminum with a black anodized finish. NOTE: Used only with slide mounted G12 Receivers.
-
Product
PXI Optical Extenders for Instrumentation
-
The Keysight Optical Extenders for Instrumentation offers capability that is modular, scalable, and upgradable to meet the challenging demands of applications requiring long distance RF paths. Configure a single link, extend the port of your PNA, or design a system that includes remote operation of the measurements while achieving an RF signal path over distances that have been impossible until now.
-
Product
PCI Smart Bus Extenders
PCIEXT-64UB - Live Insertion PCI Bus Extender
-
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment.
-
Product
VME64x Form Factor Extender, 6U x 60mm
116FFE6006-012X
-
The VME64x form factor extender 6U 60 mm allows to adapt boards for use in the same VMEbus system. It maintain the correct depth dimensions and allow the front panel to be aligned.
-
Product
CMC test Set Extender
RXB1
-
RXB1 extends CMC test sets with 4 additional binary relay outputs. Each binary output channel consists of a normally open ("make") and a normally closed ("break") contact.
-
Product
Noise Figure And Gain Test Extenders
-
SA full noise figure and gain test extender that extends the noise and gain measurement capabilities of common and low frequency signal synthesizers and noise figure meters to the frequency range of 110 to 170 GHz. This extender is designed to interface with industry standard noise and gain test systems.
-
Product
ATCA Test Extender with Zone 3
114EXT8040-0XXX
-
The ATCA extender board extends both the power and IPMB signals. It is designed for the full populated fabric slot (5 ZD connectors, P20 thru P24) and the power connector J10.
-
Product
Full Band Scalar Network Analyzer Extenders
-
Full band scalar network analyzer extenders are designed to extend low frequency scalar network analyzers to higher millimeterwave frequency ranges. These extenders offer a low cost means of producing millimeterwave scalar network analyzers while preserving the functionality and features that industry standard models offer. These extenders deliver a superior performance since they are assembled with SAGE Millimeter’s instrumentation grade frequency extenders (STE series), Faraday isolators (STF series), direct or programmable attenuators (STA series), directional couplers (SWD series) and waveguide detectors (STD series). The below standard offering covers the frequency range of 26.5 to 170 GHz. Specifications other than those listed below are available upon request.
-
Product
VME Test Extender 6U/220mm 64X w/o P0
116EXT6122-012XR
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
120 A Manual Pulse Width Extender
TLP-12012A6
-
High Power Pulse Instruments GmbH
- Pulse width extender for the high current TLP/HMM test system TLP-12010A and TLP-12010C- 6 manual selectable pulse width: 5, 10, 50, 100, 200 and 500 ns- High pulse output current up to ±120 A- High performance and high quality components
-
Product
Test Extender
PMC
-
The PMC test extender provides an active interface between a PMC carrier slot (PCI bus) and a PCI Mezzanine Card (PMC).
-
Product
VME Form Factor Extender, 3U, 60mm
111FFE3006-01XX
-
The VME form factor extender 3U 60 mm allows to adapt boards for use in the same VMEbus system. It maintain the correct depth dimensions and allow the front panel to be aligned.
-
Product
4-Ch 1.25 GHz, 16-bit D/A with DUC, Extended Interpolation, Virtex-6 - PCIe
Model 78671
-
Model 78671 is a member of the Cobalt® family of high performance PCIe boards based on the Xilinx Virtex-6 FPGA. This 4-channel, high-speed data converter issuitable for connection to transmit HF or IF ports of a communications or radar system. Its built-in data playback features offer an ideal turnkey solution for demandingtransmit applications.
-
Product
Full Band Noise Figure and Gain Test Extenders
STG-06-S1
-
Full band noise figure and gain test extenders are offered to extend noise and gain measuring capabilities up to higher millimeterwave frequency ranges. These extenders are designed to interface with noise and gain test systems that have an input IF of 10 MHz to 1.6 GHz, such as the industry standard Keysight 8970A/B, N8975A and Maury MT 2075B. The noise figure and gain test extenders include a high-performance, solid-state noise source (STZ series) and a full waveguide down converter (STC series), which consists of a Faraday isolator (STF series), full band mixer (SFB series), frequency multiplier, and IF amplifier. A frequency source with an output signal in the frequency range of 10 to 20 GHz is required as a local oscillator for the down converter. The noise source is automatically powered on and off by the noise figure meter.
-
Product
Millimeter-wave Operation With Frequency Extenders For M980xA PXI VNA
S95560B
-
banded vector network analyzer (VNA) using the M980xA PXI VNAs and N5252AW or N5262BW Frequency Extenders.
-
Product
LXI WTB Extender
60-984-001
-
The 60-894 provides a simple an effective method of joining two LXI WTB bus cables together to extend the length of available cables. It is an ideal solution for cable extension where users need to experiment with different cabling solutions without having to totally replace the cables in the system. The 60-894 provides mating connectors for the WTB on each end connected together by a set of accurate differential transmission lines to avoid additional reflections on the cable. The 60-894 is entirely passive and is compatible with the LXI specification.
-
Product
Rack Extender Kit, 9025TR, 1.5", Special
310113769
-
Rack Extender Kit, 9025TR, 1.5", Special.Rack Mount Extender Kits are used for mounting to racks with mounting rails recessed more than 1.”NOTE: Used only with slide mounted 9025TR p/n's 310104498 & 310104477.
