-
product
Network Emulation, Delay Simulation, Bandwidth Emulator & WAN Simulation
GigaNet System’s network emulation appliances provide precision, performance and predictability in your test infrastructure resulting in optimized system performance and robust system behavior under real world network conditions.
-
product
Coaxial Termination, DC to 50 GHz
85138A
The Keysight 85138A is a precision, low-reflection dc to 50 GHz load for terminating a 50-ohm coaxial system in its characteristic impedance. It is intended for use as a calibration standard. The Keysight 85138A has a 2.4 mm male connector.
-
product
Isolated Controller Area Network (CAN)
ADI isolated controller area network (CAN) transceivers provide the differential physical layer interface between the data layer link, hardware protocol (for example, embedded in some of ADI's Blackfin® processors), and the physical wiring of the CAN bus. ADI's portfolio includes transceivers with integrated iCoupler® and isoPower® isolation, providing, fully isolated off-the-shelf CAN PHY's.
-
product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
product
Single 16 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-765A-001
The 40-765A-001 terminated single 16 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
product
Power, Patchcord, ITA, 72", High Power, 2 AWG, to Ring Terminal (150 Amps)
7-222902688-072
Power, Patchcord, ITA, 72", High Power, 2 AWG, to Ring Terminal (150 Amps).
-
product
PXI/PXIe Microwave Multiplexer, Single SP8T, 18 GHz, 50 Ω, SMA, Terminated, Failsafe
42-788-021-T
The 40-788-021-T (PXI) and 42-788-021-T (PXIe) are single failsafe SP8T 18 GHz microwave multiplexers with automatic termination of unused signals. The 40/42-788 range of multiplexers are available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel. Remote versions are also available which can support one or two multiplexers in a dual slot module.
-
product
Network Attached Processor
Neuron
Built to fit in any existing and future IP broadcast infrastructure, the Neuron platform offers the most powerful processing capabilities in the industry. Neuron can accommodate a wide range of audio & video processing needs in IP environments, and bridges the gap between SDI and any type of IP media streams, protecting your investments today for future demands.
-
product
Network Automation Manager
Integrated network automation software for large or complex environments
-
product
PXI/PXIe Microwave Multiplexer, Single SP4T, 40 GHz, 50 Ω, SMA-2.9, Terminated, Remote Mount, Failsafe
42-785C-441-TE
The 40-785C-441-TE (PXI) and 42-785C-441-TE (PXIe) are single failsafe SP4T 40 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 18 GHz, 50 Ω, SMA, Internal Termination, Failsafe, Remote Mount
40-781A-022-E
The 40-781A-022 (PXI) and 42-781A-022 (PXIe) are dual failsafe SPDT 18 GHz microwave relay modules with internal terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
RF Match Networks
Enable fast, accurate, and reliable matching. Advanced Energy’s match networks expertly perform in multiple power ranges. Available in plug-and-play models or configurable units, easily install, expedite tuning, and tighten process control.
-
product
Octal 4 to 1 Terminated 50 600MHz PXI RF Multiplexer
40-761-008
This terminated octal 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
product
PXI/PXIe Microwave Relay, Single SPDT, 26.5 GHz, 50 Ω, SMA, Internal Termination, Failsafe, Remote Mount
40-781A-221-E
The 40-781A-221-E (PXI) and 42-781A-221-E (PXIe) are single failsafe SPDT 26.5 GHz microwave relay modules with internal terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
High Power Current Sensing Resistors, Wide Terminal Type
Panasonic Industrial Devices Sales Company of America
An AEC-Q200 Compliant SeriesPanasonic components specified as AEC-Q200 Compliant are consistently designed into automotive systems. However, today’s Design Engineers are specifying AEC-Q200 components to meet the high-quality standards of devices beyond automotive applications.
-
product
PXI/PXIe RF Multiplexer, Quad 4-Channel, Terminated Common, 3GHz, 50Ω, SMB
42-876A-004
The 40-876A-004 (PXI) and 42-876A-004 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 4 banks in a single slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
product
5uH Line Impedance Stabilisation Network LISN - CISPR 25
TBOH01
The TBOH01 5H LISN is a device required to setup conducted noise measurements of DC-powered devices. It is designed to be used for EMC pre-testing in the frequency range of 150kHz to 110 MHz.
-
product
Octal 4 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-761A-008
The 40-761A-008 terminated octal 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
product
Vector Network Analyzers
Vector network analysis (VNA) is one of the most essential RF and microwave measurement approaches.
-
product
Cable & Antenna Analyzer and Vector Network Analyzer
SiteOne 3028
The SiteOne 3028 is a Cable, Antenna Analyzer and a Vector Network Analyzer for cables, antennas and more, a truly handheld instrument. It covers all major communication bands from 50 kHz to 4400 MHz. It has a variety of measurement screens available, in order to accommodate all the different parameters in an antenna installation. These measurement screens can show two simultaneous graphs, from two different parameters in order to bring further clarity to your measurements.
-
product
Network Security Object Management - AlgoSec AddOns
ObjectFlow
Manage network security objects across your entire multi-vendor network.
-
product
PXI Remote Mount Single SP6T Multiplexer 40GHz 50, SMA-2.9, Terminated
40-785B-541-TE
The 40-785B-541-TE is a remote mount single 6-channel 40GHz terminated microwave multiplexer. The 40-785B range of multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 26.5 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
42-785C-432-TE
The 40-785C-432-TE (PXI) and 42-785C-432-TE (PXIe) are dual failsafe SP4T 26.5 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
product
PXI Microwave Relay, Single SPDT, 26.5GHz, 50Ω, SMA, External Termination
40-781A-321
The 40-781A-321 (PXI) and 42-781A-321 (PXIe) are single SPDT 26.5GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
Network Security Validation Platform
FireDrill
AttackIQ FireDrill is a game changing platform that seamlessly integrates into any existing network, delivering immediate visibility into your security program so you can mitigate risk, and maximize security ROI.
-
product
PXI/PXIe RF Multiplexer, Quad 4-Channel, Terminated, 8GHz, 50Ω, SMA
42-882B-004
This multiplexer has low VSWR characteristically over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensures a long service life with no wear out mechanism, making the 40/42-882B MUX ideal for ATE systems requiring frequent and fast operating RF switching.
-
product
1U Rackmount Network Appliance Platform With Intel® Celeron® N3350 Or Atom™ X5-E3940 Processor And 6 LANs
NA345R
The NA345R supports the Intel® Celeron® processor N3350 and Intel® Atom™ x5-E3940 processor. The reliable 1U rackmount network security platform features six Gigabit Ethernet ports using Intel® i211 Ethernet controller and supports one pair of LAN bypass function. It comes with one DDR3L-1866 SO-DIMM slot with up to 8GB non-ECC memory. One 2.5-inch SATA3 HDD and one mSATA are available for sufficient storage. Furthermore, it comes with one HDMI port for high definition display, two USB 3.0 ports for external devices, and one console port for device network management. The LED indicators are available on the front panel for convenient monitoring of power, HD, and LAN activity. To keep system running smoothly, the NA345R is equipped with a built-in watchdog timer which features 255 levels for system reset and 7 levels for LAN bypass. Finally, it is compliant with Win10 and Linux. Bringing high security and high reliability at a low cost, the NA345R is aimed for VPN, network bandwidth controller, and firewall applications.
-
product
Detector of Earth Faults on Multi/Single-Core Terminations
CableTroll 2310
CableTroll 2310 is an indicator for detection of earth faults (PtG) on multi-core and single core cable terminations. The unit uses NorTroll type current sensor (CT)
-
product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 3GHz, 50Ω, N-Type, Terminated, Remote Mount
40-785C-562-TE
The 40-785C-562-TE (PXI) and 42-785C-562-TE (PXIe) are dual SP6T 3GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
product
PXI/PXIe Microwave Multiplexer, Dual SP8T, 18 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
42-788-022-TE
The 40-788-022-TE (PXI) and 42-788-022-TE (PXIe) are dual failsafe SP8T 18 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
