-
Product
Cable Tester & Cable Tracer & Multi-Functions Lan Tester
M-CT-430A
-
Fuzhou Metricu Technology Co Ltd
The multifunction LAN tester M-CT-430A is designed for maintenance and installation of cable, cable tracer, and HD Coaxial video level meter test in one equipment. The unit supports detect the near-end, mid-end and far-end fault point of RJ45 cable connector, and also supports Port Flash, PING test, IP address Scan, Link Monitor. Installers take the all in one cable tester, making working conditions safer and increasing productivity.
-
Product
PCIe Fast Multifunction, Multichannel Counter Board, Optically Isolated, RS-422 Inputs
APCIE-1711-24V
-
The APCIe-1711 board is a fast multifunction and multichannel counter board for the PCI Express bus. The strengths of this board are its wide range of applications and high precision and reliability for industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provide the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied software. The flexible programming facilities on this board allow many differentuser applications to be quickly and easily developed and reconfigured as further requirements arise. Thanks to the FPGA board structure, further counting applications canbe realised through software adaptation.
-
Product
Multifunction Calibrators
-
These bench multifunction calibrators source, simulate, and measure pressure, temperature, and electrical signals with exceptional precision. They can automate calibration procedures and maintain a wide range of temperature and pressure transmitters, multi-meters, pressure gauges, and more.
-
Product
Insulation & Multifunction Tester (LCD Display)
1154 TMF
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
Product
CalPod Drive Cable, 40 GHz, 2 Meter
85553A
-
This cable provides the bias voltages and control signals for operation of the 40 GHz CalPod modules. This cable is supplied with the 85540/41/42A CalPod modules.
-
Product
Smart I/O & Communication
-
Fulfill the customized expansion, provide faster response to market and include isolated / non-isolated communication and digital input/output modules
-
Product
2 Port BRI-S/T ISDN Simulator PCI
BRI-2ST-PCI
-
The most inexpensive ISDN simulator on the market. Designed in standard PCI card form factor it has two S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network. Simulator card does not require any OS drivers, completely software independent and it take only power from the host computer.
-
Product
PXI Single 44x4 Matrix, 2 Pole Switching
40-523-022
-
Medium density PXI dual 44x4, 2-pole matrix - it is also available in reed relay formats of 1-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
Product
Portable Multi-Function Recorder
Platinum 2.5K/Portable
-
The Platinum 2.5K Portable Multi-Function Recorder is packaged in a rugged case with quick connect interfaces for fast and simple field connection. Interface cables are provided with shrouded banana jacks that couple easily with a variety of measurement CT’s and voltage scaling devices offering complete flexibility for power utility and industrial use. The Platinum 2.5K Portable Multi-Function Recorder utilizes a 40GB solid state drive that eliminates the need for a mechanical hard drive and stores over 1,000 fault and disturbance records at once. It meets regulatory compliances including PRC-002-2.
-
Product
4Relay/4DI IoT Modbus/SNMP/MQTT 2-Ports Ethernet Remote I/O
ADAM-6266
-
4ch relay/4ch digital input(counter)Protocols:MQTT(TLS),SNMP,Modbus TCP,RESTful,ASCIIGCL to perform basic logic control rulesCloud access: Data update to AzureAuto-bypass function to ensure daisy-chain data transmissionPeer-to-Peer function to map I/O statusBuilt-in web serverWatchdog timer to recover the system
-
Product
MIC-780 Series I-Module With 2 X PCIex8
MIC-78M20-01
-
2 x PCIEx8Support 2 x 4cm FAN (Optional)Support additional 2.5" HDD/SDD kit (Optional)Diemension with MIC-780 : 133 x 195 x 255 (mm)
-
Product
PXI Single 2 x 2 Fibre Optic (M Mode) ST M50
40-860-512-M50
-
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
DB25F-DB25F, 25-Pin D-Sub Cable for SMUs, Low Leakage, 1 m
782015-01
-
DB25F-DB25F, 25-Pin D-Sub Cable for SMUs, Low Leakage, 1 m
-
Product
1 MS/s, 16-Bit, 16-Ch Multifunction PCIE Card
PCIE-1816
-
16 analog inputs, up to 1 MS/s, 16-bit resolution2 analog outputs up to 3 MS/s, 16-bit resolutionSupport Analog and Digital Trigger for AI/OSupport Waveform generation for AO24 programmable digital I/O linesTwo 32-bit programmable counter/timersOnboard FIFO memory (8k samples)Support for Microsoft Windows 10/11 and Linux
-
Product
1-Ch SSI Absolute Encoder EtherCAT Slice IO Module
AMAX-5082
-
Encoder Type: SSI (Binary / Gray code)Latch Counter ValueComparator *2Compare trigger Output *2
-
Product
Shock/Bump Multifunctional Tester
DP-201
-
King Design Industrial Co., Ltd.
Shock or bump test mainly simulate the impact effects of product and its components encountered in usage and transit process. Through standard and high-reproducibility instant energy exchange, you can analyze the product ability to tolerate the strong external stress and the degradation of structural weaknesses to quickly obtain the data of structure strength, anti-shock appearance and anti-drop. Shock tester is one of destructive experiments, and do destructive test on the product to evaluate the product reliability and monitor the consistency of production line.
-
Product
PXI 2 Amp Multiplexer, 4-Bank, 16-Channel, 1-Pole
40-657A-001-4/16/1
-
The 40-657A-001-4/16/1 is a 4-bank, 16-channel, 1-pole MUX and is part of our range of High Density 2 Amp Power Multiplexer Modules available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
Product
LCD Multifunction Cable Tester
MT-7059
-
Display test result on large LCD for easy reading and cable status identificationThe wire can be tracked directly in connection with Ethernet service, router, and PC terminalValidate and troubleshoot wiring on RJ11/RJ45 cables, Coaxial cable, USB cable, IEEE 1394 cableTest cable status for continuity, shorts, opens,miswired, crossover9 different tones selection for convenience use under different environment conditionAll installation and maintenance fields of telecommunication, networking, cable TV and more
-
Product
PXI 2 Amp Multiplexer, Single 16-Channel, 4-Pole
40-635A-003
-
The 40-635A-003 is a single 16-channel, 4-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Ethernet I/O Modules
ADAM-6000
-
Advantech's Ethernet I/O Modules, ADAM-6000 series, accomplishes this integration easily through the latest internet technology, so that it can remotely monitor the device status more flexibly. ADAM-6000 modules are empowered by Peer-to-Peer (P2P) and Graphic Condition Logic (GCL), and can perform as standalone products for measurement, control and automation with Advantech's P2P and GCL technology.
-
Product
GPIB Cable, 2 Meter
10833B
-
The Keysight 10833B (2 meter) GPIB cable is engineered for exceptional reliability and durability even under the harshest conditions. When you buy Keysight GPIB cables, you can be sure of automatic, seamless compatibility between computers and instruments throughout your system. GPIB interface cables, cards, and software for your computers make it easy for you to access and control instruments and exchange data - and it all starts with the cables to connect your computer and instrument. Keysight GPIB cables are fully compatible with the IEEE 488.1 mechanical specification.
-
Product
Pocket Size Multi-Function Autoranging Multimeter
HH2219
-
Pocket Size Multi-function Auto-ranging Test Indtrument. 4000 count LCD display, 12mm figure heigh. Full Auto Ranging with symbolic display. Measuring AC/DC Voltage up to 450V. Resistance test up to 40MΩ. Test Frequency 10-100kHz
-
Product
12-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-8
-
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
Machine Vision Computer with Built in I/O
Neousys Nuvis
-
Nuvis-5306RT , Nuvis-534RT, Nuvis-7306RT contain interfaces for connecting to all necessary devices: LED lighting controller, camera trigger, encoder input, PWM output and digital I / O lines.- Intel® 7th Gen Core ™ i7 / i5 65W / 35W, up to 32GB DDR4- Built-in I / O- 4-CH CC / CV backlight controller- 4-CH trigger camera- 1-CH quadrature encoder input- 8-CH isolated DI and 8-CH isolated DO- Built-in camera interfaces- 4-CH IEEE 802.3at Gigabit PoE + ports- 4-CH USB 3.1 Gen1 ports- NVIDIA 75W GPU Support
-
Product
CPCI 48 Input I/O Card with Zilog Z8536 I/O Controller
CPCI-48IN
-
The input board consists of three Zilog Z8536 controllers for DC input control. An FPGA provides the timing and control. Each input has its own optical isolation, and supports a hardware adjustable resistor/opto-diode combination for various input voltage ranges. An AMCC PCI controller provides the interface to the host computer. All I/O is accessible from the front panel.
-
Product
PXI 2 Pole 18 way Mux with 2 Pole 18 way sen
40-658-002
-
This PXI multiplexer combines a 2-pole 18-way power distribution MUX with a second lower power 2-pole 18-way MUX in one convenient single slot PXI module.The module is ideal for power distribution where power and sense signals are required to be connected to an array of devices under test. This multiplexer is also convenient for making 4 wire low resistance measurements by supplying the resistor under test with high current through the power MUX and sensing the voltage drop through the sense MUX.
-
Product
MiniPCI Express to M.2 PCIe Adapter (B-key)
SKU-089-12
-
MiniPCI Express Adapter has M.2 (B-key) connector. It allows connection M.2 modules with B-key to a MiniPCI Express circuit. Adapter can be installed in Full size or Half size MiniPCI Express circuits, and this Adapter supports PCI express, SIM and USB 2.0 interfaces.
-
Product
LVDS Digital I/O with Virtex-6 FPGA - 3U VPX
Model 52610
-
- 32 bits of LVDS digital I/O- One LVDS clock- One LVDS data valid- One LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAs- DMA controller moves data to and from system memory- Up to 2 GB of DDR3 SDRAM- PCI Express Interface- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
Product
PCI-6110, 4 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device Multifunction I/O Device
777475-01
-
4 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6110 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6110 is ideal for a variety of applications, such as stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6110 dimensions require chassis slots that can accommodate full-length PCI modules.
-
Product
32-CH Separate I/O Terminal Base
HSL-TB32-MD
-
The HSL-TB32-MD discrete I/O terminal bases provide reliable and convenient wiring for HSL-M series products. The separate connection can make it easy to wiring, and the separate fuse can protect each I/O point. This low cost terminal base is particularly useful for users who need convenient way to construct their own signal ?Vcondition arrangement.
