-
Product
End of Line Noise Test System
-
End of Line Noise Test Systems from VIacoustics are designed to support end of line product noise testing on factory floors and quality assurance environments. Using the Limit Analysis features of the Nelson Acoustic Trident software, users can set noise emission maximum, minimum or control range criteria based on Awtd and/or 1/N octave band criteria. Criteria can be customized for most any type of product based on the noise emissions of known good and bad units. The large front panel Pass/Fail indicator allows operators to quickly determine if units meet the criteria. Data on units that fail can be exported for further analysis.
-
Product
Fluid Level Sensor
-
The output of the fluid level sensor is a voltage which changes in direct proportion to the level of fluid in the probe. The difference in permittivity between air and the fluid being measured changes the capacitance between the probe's two concentric tubes as the level changes. An RS232 connection to a PC allows the user to calibrate the fluid level and thermal drift compensation. The probe is factory replaceable, allowing the electronics to be re-used should the probe become damaged or if a new probe length is required.
-
Product
FADEC/EEC Test Platform
-
The FADEC/EEC Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of full-authority digital engine control (FADEC) and electronic engine control (EEC) units of both rotary- and fixed-wing airframes. The system simulates one or more turbofan engines, including its sensors and actuators for use with the most sophisticated FADECs and EECs on the market. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
Test DVD For OmniMic Precision Measurement Systems
OMDVD Version 1
-
The Dayton Audio OMDVD Test DVD brings the ease of the OmniMic V2 system to measurements of 5.1-channel audio systems. It’s the essential tool for professional installers and home theater enthusiasts to ensure proper audio calibration and optimization of a home theater or multichannel music system for the highest possible performance. The full functionality of the OmniMic V2 measurement system is now available through every channel of a 5.1-channel audio system thanks to the OMDVD Test DVD’s suite of high-quality test tones, and an intuitive menu structure that has been optimized for ease of use.
-
Product
Mobile Measuring & Testing Systems
-
Individual testing tasks for technical plants and large machines often require the use of a large number of measuring instruments on site, which are difficult to network with each other and which, in the case of complex measurements, require a lot of experience and time in operating the measuring equipment and analysing the recorded measured values. The applications and possible uses can be quite different:
-
Product
Pro-Stik II Level Sensor
7330
-
The Drexelbrook 7330 Pro-Stik II Series are intrinsically safe programmable liniear position sensors ideal for monitoring in a variety of liquids and tanks.These position sensors are based on the proven magnetostrictive technology and are available in different models including our popular explosion proof and flame proof models. The 7330 Pro-Stik II position sensors are loop powered and available with a rigid 316 stainless steel or flexible PVDF materials.The probe features a security feature by utilizing a timing sequence that is used to unlock the probe for programming. This ensures that the span cannot be accidentally programmed by someone in the field.All of the sensor's electronics are SMT components integrated into the 5/8" diameter sensing tube offering greater options for insertion and mounting in tanks and vessels.
-
Product
Sound Level Meters
-
Is designed to respond to sound in the same way as the human ear and to give reproducible measurements of sound pressure levels.
-
Product
Standalone with Drop-In Test Systems
800 Series ATE
-
The Circuit Check 800 Series ATE provides the versatility of utilizing the economical drop-in fixturing present in the 600 Series or an integrated dedicated fixture, while simultaneously providing the increased test equipment capacity of the 1000 Series. This combination produces a cost effective full turnkey test solution.
-
Product
Optics Test Systems
WAS 160: Wedge Angle Sensor
-
Optik Elektronik Gerätetechnik GmbH
Portable measuring head for wedge errors and radius of curvature, eg of car windshields, airplanes and helicopters. It can be used for any other glass panes.
-
Product
LabVIEW Professional Development System
-
ntegrate hardware from a variety of measurement instruments and devicesIntuitive graphical programming syntax to simplify automationBuild custom user interfaces for engineering applicationsBuilt-in algorithms for signal processing, analysis, math, and PID controlSoftware engineering tools to debug, validate, and deploy codeOne-year SSP membership for technical support, online training, and software upgrades
-
Product
Shield Level / Pathloss Equipment
PAMS & PAMS-C
-
PAMS is a user-friendly, transmitter and receiver system that measures shielding effectiveness in RF shielded enclosures. Lightweight and compact, each PAMS unit measures approximately 12” x 5” x 5” and weighs 5.5 lbs., making PAMS ideally suited to field measurement tasks. Rugged construction insures instrument survivability in a field test environment. PAMS-C is a simple and efficient solution for quickly identifying shielding faults in an RF shielded enclosure. Cousin to the original PAMS used extensively by customers operating RF Shielded Enclosures, PAMS-C gives commercial end-users everything needed to measure shielding effectiveness levels of critical infrastructure - all with minimal or no interruption to normal operations.
-
Product
Integrated/Separated Explosion-Proof Ultrasonic Level Gauge
HR9100E
-
HighReach Measuring & Controlling System Co.,Ltd
1. Safety / use of die-cast aluminum alloy waterproof, explosion-proof shell; the explosion-proof grade of the instrument reaches Exd (ia) IIBT4 2. stable and reliable / we choose high-quality module key components from the power supply Part of The Circuit Design Stable and Reliable Devices CAN Completely Replace imported Instruments. 3. Patented Technology / Ultrasonic Intelligent Software CAN with Carry OUT Intelligent echo Analysis, the without the any the debugging and OTHER Special Steps, the this Technology has The function of Dynamic Thinking, Dynamic Analysis 4. High precision / sound wave intelligent patent technology owned by our company, so that The accuracy of the ultrasonic level gauge is greatly improved, the liquid level accuracy reaches 0.3%, it can resist various interference waves, the failure rate is low, the installation is easy, and the maintenance is easy. The instrument is a non-contact instrument and does not directly contact with liquid. Users can use this manual to calibrate the instrument. 6. The protection level of multiple protection/instrument reaches IP65; all output and input lines have lightning protection and short circuit protection.
-
Product
Mezzanine System
5033
-
ECM P/N 5033 provides eight channels of RS485 / RS422 I/O. The 110 ohm termination for each channel is enabled or disabled in software. Disabling termination saves power by eliminating unneeded or redundant termination. Speeds of up to 20 Mega bits per second are possible, but this design also features a 250K bits per second slower edge rate mode. The 250K bit mode is valuable when EMI is more of a concern and throughput is not important. All channels power up as inputs with the outputs disabled.
-
Product
Power Device Test Systems
-
Power semiconductors are devices that control electric power, and are used in automobiles and a wide range of electrical products. Our power semiconductor test systems, developed and provided by CREA, an Advantest Group company, specialize in testing power semiconductors that handle high voltages and large currents, and have special safety features for this purpose.
-
Product
EOL RF Functional Test
AS652
-
With this RF test platform, integrable according to the specific needs of the product, we cover a very wide range of test needs with manual feeding.Ergonomics have been fully observed in the design, including the option of servo adjustment of the working height according to the operator.
-
Product
eBIRST™ – Switching System Test Tools
-
Switching systems are an important part of many test systems, however, the switching system is in a vulnerable place. When accidents happen that can cause a faulty device, you need a way to get the system up and running again with a minimum of effort and operator skills.
-
-
Product
X-ray Non-Destructive Testing (NDT) System
DynamIx HR / Series 5
-
High precision 12-bit 50µm reading allows inspection of minute image details. Wide dynamic range resulting in wide allowance of X-ray exposure value.
-
Product
Mixed Signal Test Systems
MTS1020i
-
The MTS-1020i is a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
Product
High Level Language Debugger and Emulator Tool
Universal Debug Engine
-
Programmierbare Logik & Systeme GmbH
With Universal Debug Engine (UDE®) PLS offers on top solutions for software development of systems-on-silicon including debug support for the 16 Bit and 32 Bit microcontrollers C16x, C166™, ST10F276, ST10F280, XC166, XC2000, XE166, XMC4500, C166S V2, SDA6000, TriCore™ from Infineon and STMicroelectronics, Power Architecture® MPC55xx, MPC560x, MPC563x, MPC57xx from NXP™, PowerPC PPC440SPe from AMCC, Power Architecture® SPC560, SPC563, SP574 from STMicroelectronics, ARM7™, ARM9™, ARM11™, Cortex™-M0, Cortex™-M0+, Cortex™-M3, Cortex™-M4, Cortex™-M7, Cortex™-R4, Cortex™-A8, Cortex™-A9, XScale™, SuperH™ SH-2A derivatives in a new multicore debug environment as well as technical support. The extensive feature list includes functions like: high speed and flexible target access via JTAG, cJTAG with OCDS L1, EmbeddedICE, OnCE, COP, DAP, DAP2, SWD support, OCDS L2 trace, MCDS trace, CoreSight™ trace, ETM trace, ETB trace, Nexus trace, ASC, SSC, 3Pin and CAN, in-system FLASH memory programming of FLASH / OTP with UDE MemTool, support of various RTOS, OSEK® and test automation tools.
-
Product
Sound Level Meters
-
A sound level meter is used for acoustic (sound that travels through air) measurements. It is commonly a hand-held instrument with a microphone. The diaphrahm of the microphone responds to changes in air pressure caused by sound waves.
-
Product
Entry Level Beam Profiling
BeamMic®
-
BeamMic is simplified set of measurement tools for the entry level beam analysis user. The camera-based beam profiling system consists of a camera and analysis software. Often times, this system will need to be used with beam attenuation or beam sizing accessories, depending on your laser application. BeamMic includes a complete set of high-accuracy measurements, and features a rich graphical interface. For the laser technician, this entry-level software will easily help you quickly become familiar with the many benefits of beam profiling.
-
Product
Resilient Modulus and Asphalt Testing System
-
The Resilient Modulus software features built and test sequences, and the capability to specify user defined sequences. Contact stress is automatically adjusted according to the above procedures as selected. Available waveforms include haver sine, sine, square and triangular, along with a user defined waveform selection. Optional peak & valley compensation ensures proper and quick matching of the load parameters. Real time displays of the prescribed versus actual dynamic load or the dynamic deformation measurements by each sensor are always present. Deformation ratio of the two sensors, Rv (to ensure that the two deformation sensors are in agreement) and Mr are also calculated in real time. During export, curve fitting is done to fit the results to models that predict Mr as a function of σm, σd, and CP (cell pressure). Four different functions are calculated automatically
-
-
Product
In-line vacuum test systems
-
Ensuring that products meet the highest quality standards is absolutely essential in the manufacture of food, pharmaceutical and cosmetic products in particular.Leak-tight product containers have a major role to play here. Leak-tight product containers have a major role to play here. Leakages allow the contents of a container to get out, but more importantly they also allow germs to get in, rendering the contents unusable.INDEC vacuum test systems monitor containers for leak tightness fully automatically within the production process. A wide range of containers, including bottles, jars and cans as well as tubs and trays, are tested for leak tightness by means of a non-contact inspection.The means to this end is a pre-existing vacuum or a vacuum created in the container expressly for the purpose of leakage testing. Containers which are not leak-tight are reliably identified and automatically rejected.These processor-controlled test systems are highly reliable and extremely easy to use, qualities which have played no small part in making them the first choice already for many companies throughout the world.
-
Product
DC Power / Energy Absorber Test System
-
AMETEK Programmable Power, Inc.
The Energy Absorber Test System includes power supplies and a regenerative energy absorber with a rating of 400VDC at ±150A. The system consists of DC power supplies, an AC distribution and interlock system, an energy absorber chassis and an absorber load resistor chassis. The power sources are equipped with a remote control option allowing control via GPIB or with front panel controls in local mode. The operation of the specific parts of the system is described in the sections below.
-
Product
6TL24 Combinational Base Test Platform
H71002400
-
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
Product
Spectrophotometer & Integrating Sphere Test System
LPCE-1
-
This Test System is suitable for photometric and colorimetric measurement of luminaries such as Energy-saving lamps, Fluorescent lamps, HID lamps (high voltage sodium lamps and high voltage mercury lamps), CCFL and LED. The measured data meets the requirements of CIE and IES LM-79 for the measurement of photometry and colorimetry.
-
Product
Silicon-Microphone 8Ch Auto Test System
BK9015
-
Based on the BK3011 MEMS Mic Tester, the BK9015 is our fully automatic 8 channel MEMS (Silicon) mic sweep tester. Testing up to 8 DUT's simultaneously, the BK9015 can test 8 mics simultaneously and sort them according to passing grade and cause of failure! Because it uses a sweep test, it can check characteristics for the entire frequency range. Your data can be viewed in real time or stored so you can analyze problems or trends.
-
Product
Electrical Test System TY-CHECKER
Type E Series
-
High-speed, high-precision testers offered with a broad lineup, matching a range of test point numbers. Can be used alone and on our press systems.
