-
Product
CAN Sensor/ Interface
Current
-
Reach Technologies’ CAN Current Sensors sense and digitize conductor current for collection via CAN. The module is ideal for conveniently adding current data to a distributed CAN network. The CAN Current Sensor is configurable via J1939 or CANopen stacks, and are available in Hall Effect and shunt variants.
-
Product
Microhardness Tester
-
By adopting the Load-cell load system, multi-stage load switching is possible.
-
Product
Arc Ingintion Tester
-
The product is designed to carry out Arc Ignition Test as per IS/IEC 60947-1 Clause 8.2.1.1.2 (material used for electrical products). The adjustable current source is 230V AC @ 33A. The load is adjusted to get 32.5A at 0.5 power factor. Included on control unit are Digital Voltmeter, Digital Ammeter, Digital Power Factor Meter and Micro Controller based programmable Sequence Timer with LCD display for display & setting. The arrangement is made to mount the test piece with electrodes as per the specification given in the standard.
-
Product
Tilt Position Sensors
-
Available with any measurement angle between 15 and 160 the P603 tilt sensor operates a gravity driven, oil damped pendulum with a very low settle time and durable housing. Our tilt sensor has proved popular in marine applications because like our linear and rotary sensors we have used highly durable and corrosion resistant materials.We also offer the S623 which is waterproof sealed for continual submersion to IP68 350bar, 5000psi, 3500msw
-
Product
Hand Dynamometer Logger Sensor
NUL-237
-
This sensor comes with a hand held unit with a built in strain gauge. The sensor measures the pressing force on the hand held unit.
-
Product
Peeling Tester
BN-3
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3;Inspection standard: JB/T4279.6-2008Used to measure the film adhesion property of enameled round wires with nominal conductor diameter of 1.0mm and below;High-end SCM control is used;Set arbitrarily the number of twist;LED would automatically display the number of twists;Twist counter performs accurate and reliable counting;High-strength steel scraper would complete sample scarping at once, easy to operate and use.
-
Product
Two-Pole Voltage Tester
P-4
-
Sonel P-4 is reliable, particularly durable and safe 2-pole testers, which enable testing voltage, circuit continuity and phase sequence. It has been designed for use in extreme conditions both in industry and commercial applications. Advanced technology, a high level of safety and user-friendliness are the key features of the P-line voltage testers.
-
Product
Sensors
-
A device that produces an output signal for the purpose of sensing a physical phenomenon.
-
Product
CT Core Tester
VCCT
-
Veer make CT Core Tester VCCT is portable & easy to use Instrument. It is very useful to measure Voltage & Current of Electrical Steel like Toroidal Cores of different grade and size. VCCT is designed to test a lamination stack Toroidal Core. A Quality is judged by comparing the value of voltage applied & consumption of current.
-
Product
3D Profile Sensor
Z-Trak2
-
Z-Trak™2 is a new family of 3D profile sensors built on Teledyne Imaging’s 3D image sensor technology, ushering in a new era of 5GigE 3D profile sensors for high-speed, in-line 3D applications.
-
Product
Bursting Strength Tester
-
TESTEX Testing Equipment Systems Ltd.
Bursting Strength Tester is used to test the strength of bursting for fabric. When you do bursting test, mullen burst tester is a wise machine for you.
-
Product
Water Content Testers
-
Water content tester, cloulometric Karl Fischer titrator, crude petroleum water content tester
-
Product
LAN Cable Tester
21-6568-00
-
The Handheld Lan Cable Tester is an intelligent continuity tester for LAN cables, Phone cable and Coaxial cable. Open, short and misswiring are also tested. It provides the installers an ease of use which keeps you from wasting time through complex menus.
-
Product
Rail Pressure Tester
RPT-5
-
The RPT-5 device is used for performing an independent, parallel pressure measurement in storage fuel systems such as Common Rail (Diesel) and GDI/FSI (petrol). The tester, apart from pressure value, also diagnoses power supply of a sensor. Additional advantage is the capability of automatically detecting the terminals of the sensor, which is useful especially when using needle probes.
-
Product
Light Intensity Sensor
E-LIS
-
Detects and measures the luminous intensity of light. Ideal for monitoring unmanned closets, telecom rooms, remote data rooms, or other low traffic facilities. Applications from 0 to 128,000 lux. Human eye response (540 nm peak sensitivity). IR and UV rejection. RJ45 connector. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS. Compatible with ENVIROMUX-2D/5D/16D.
-
Product
Heavy-Duty Continuity Tester
TE6-0710
-
Hangzhou Tonny Electric & Tools Co., Ltd.
*Designed to test circuits while power is OFF*2- 1.5V Button cell batteries included. *Durable ABS housing.*High-quality materials for long-lasting durability.*Sharp tip for probing circuits.*Electrical Multi-Testers for almost any automotive repair on all 6, 12 , 24 and 48 volt systems.*Suitable for a broad range of household, car, trucks, boats, trailers, vans, motorcycles, industrial and commercial uses
-
Product
FPD Tester
2918
-
The 2918 FPD tester provides 8k Super Hi-Vision (7680x4320/ 8192x4320) for testing Full 8k@60/120 Hz resolution (32/64 lane V-by-one) is supported by one tester.
-
Product
Alternator Tester
ALTALYZER Tester
-
The Altalyzer tester is used to check the correct operation of alternators equipped with electronically controlled voltage regulators. In alternators of this type, the charging voltage is not constant, but varies depending on external factors such as: engine revolutions, number of current receivers, etc. The voltage at a given moment is determined by the motor controller by sending the appropriate information to the alternator.
-
Product
Multiport JTAG Tester
XJQuad
-
XJQuad is a 4-port version of the XJLink2 USB-to-JTAG controller targeted at PCB manufacturers. It is supplied with XJRunner software for running XJDeveloper test systems. With a range of special features it is particularly suitable for concurrent/parallel testing on the production line. Each of the four ports has a high-speed interface which can be connected to up to four JTAG chains on each Unit Under Test (UUT).
-
-
Product
Wire Mount Testers
-
Is designed to measure and control the DC resistance, electrical capacity, insulation resistance of electrical circuits and check the electrical insulation strength of electrical circuits.
-
Product
Softness Tester
-
TESTEX Testing Equipment Systems Ltd.
Softness Tester, to determine the softness of leather and coated fabrics and other soft materials. Softness tester does not need samples to be cut from leather prior to testing.
-
Product
Peugeot Oxygen Sensor
KS60113 - Peugeot
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
Leeb Hardness Tester
THL210
-
LCD display of 128×64 matrix with back-light, showing all functions and parameters. Converts to all common hardness scales (HV,HB,HRC,HRB,HRA,HS). English displaying and easy and convenient menu operation. Powerful PC Software available and USB 1.0 interface and USB with Protective Membrane. 7 types of Impact Device optional, which don't need to be recalibrated when changing them. Memory of 600 groups data（impact times:32～1）. Lower limit setting and sound alarm. Material of “cast steel” is added; HB values can be read out directly when D/DC impact device is used to measure “cast steel” work piece. Printer be separated from main unit and copies of testing results can be printed as required. Normal battery AAA and big power store while USB connected and charging controlling circuit. Inbuilt function of Software Calibration.
-
Product
Magnetic Field Tester
MS-440
-
This device recognises fast and simply magnetic fields generated by electric reels and permanent magnets.
-
Product
Vibration Testers
-
Analyzes vibration patterns within mechanical systems or individual components and structures to identify defects and evaluate the test object's overall condition.
-
Product
Crease And Stiffness Tester
DRK153
-
Shandong Drick Instruments Co., Ltd.
Whether this is by hand or by mechanical means. The crease recovery (spring back) can result in forces, which distort the erected carton or cause stresses to be applied to closures, which reducetheir effectiveness. With the Crease and Stiffness Tester, the Crease recovery is determined by the decrease in resistance offered by creased board after it is folded 90° at the crease measuring the recovery force after 15 seconds. Board Stiffness is determined by bending a 50mm length of board through a 15° angle.
-
Product
Laser Sensors (Triangulation)
opto NCDT
-
optoNCDT sensors have set milestones for industrial laser displacement measurement. Whether for displacement, distance or thickness measurement, Micro-Epsilon laser sensors are considered one of the best in their class. These laser sensors are used e.g. in measurement and monitoring tasks in factory automation, electronics production, robotics and vehicle construction.
-
Product
Plunger Tester
PL2003
-
Designed and manufactured in accordance with ASTM F414, DOT571.109, F870 & JIS D4230 standards. New generation of PL-2000X series Plunger Testers, equipped with servo-hydraulic system to control the testing speed, are available fpr customers to select the suitable model. Test functions including Radial elasticity test, Tread footprints test, Tire dimension test, Bead unseating test, Lateral elasticity test and Pressure distribution analysi for Footprints.
-
Product
Hardness Testers
-
The hardness tester products you will find at PCE Instruments (PCE) are used for determining surface hardness. Each hardness tester uses a standard method of measurement. The measuring principles of most hardness tester devices are based on either the penetration of a diamond indentor into the material being tested or a calculation related to the force of the rebound after striking the tested material. However, material hardness can also be measured accurately through ultrasonic testing. Each hardness testing method has its benefits and will allow for the precise measurement of material hardness in accordance with the technical specifications of the hardness testing instrument.
