-
product
Modular and Scalable Multifunction Switch/Measure Units
EX1200 Series
The EX1200 product family is a modular and scalable series of multifunction switch/measure units that can be configured to address a variety of applications in the mechanical data acquisition and electronic test environments.
-
product
High Performance Data Acquisition
CPCI-AD8
The CPCI-AD8/16 module provides a 3U high performance data acquisition subsystem. There are (8) eight or (16) sixteen 100/200 KSPS ADC’s for maximum performance. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.Instrumentation amplifiers provide over-voltage protection and gain on a per channel basis. The CPCI-AD8/16 can also accept external scan and trigger signals from a front panel connector.
-
product
16-CH Digital Input Module
ND-6053
- Channels: 16 DI- Channels: 16 DI: Logical 0: close to GND; Logical 1: open; Effective distance: 500m- Wet contact: TTL level- Programmable input polarity
-
product
Data Acquisition System - 3U 1-Slot
DAQ-31CP0G
The DAQ-31CP0G is a preconfigured rugged system with a high-performance, low power ARM® Cortex®-A9 processor. It is ideally suited to support a multitude of data acquisition applications that require high-density, multichannel, programmable communications consisting of: ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939) and Dual-Port Gig-E Ethernet.
-
product
3-CH RTD Input Module
ND-6013
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
Digital I/O Module
ND-6050
- Interface: RS-485- 7 TTL digital inputs- 8 open collector DO- Output up to 30V, 30mA max. load- Programmable input polarity
-
product
8-CH Relay Output Module
ND-6063
- 8-CH relay outputs- Output Type: 8 Form A- Contact Rating: AC: 0.5 A / 125 V; DC: 1 A / 30 V or 0.3 A / 110 V; ON/OFF Interval Time: 3 ms- Breakdown Voltage: 500 VAC (50/60 Hz)
-
product
8DI/8DO Modbus RTU Remote I/O
ND-6150
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
-
product
4-CH 24-Bit Universal Input USB DAQ Modules (OEM Version Available)
USB-2401
The USB-2401 is a 24-bit, 4-channel simultaneous-sampling universal input USB DAQ modules featuring built-in signal conditioning circuitry, providing direct measurement of commonly used sensors including current output transducers, thermocouple, RTD, load cell, strain gauge, and others. Individual channels can be programmed to measure different signal types. The USB-powered USB-2401 is equipped with removable screw-down terminals for easy device connectivity, and the included multi-functional stand fully supports desktop, rail, or wall mounting.
-
product
16-Channel 250kSa/s USB Modular Multifunction Data Acquisition
U2351A
The U2351A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2351A to simulate simultaneous analog input acquisition.
-
product
I-Pi SMARC Development Kit based on Qualcomm® Robotics RB5 Platform
I-Pi SMARC RB5
The I-Pi SMARC RB5 is a SMARC-based AIoT and robotics development kit harnessing ADLINK LEC-RB5, powered by the Qualcomm® QRB5165 SoC with Qualcomm® Kyro™ 585 octa-core CPU (8x Arm Cortex-A77), and Qualcomm® AI Engine.
-
product
Data Acquisition Module for Embedded Systems with IO60 expansion
IO60-M410
WINSYSTEMS’ IO60-M410 is a reliable data acquisition module for embedded systems with IO60 expansion featuring 24 GPIO (General Purpose Input-Output) tolerant to 30 V DC. Activity LEDs indicate device communication and DAC fault. WINSYSTEMS can provide custom configurations for OEM clients. Please contact a Applications Engineer through our contact page for details.
-
product
I-Pi SMARC Development Kit Based On NXP® I.MX 95 Six-Core Arm® Cortex-A55, M7 & M33
I-Pi SMARC IMX95
The ADLINK LEC-IMX95 is a powerful and versatile SMARC module that delivers high-performance computing, graphics, machine learning, and vision capabilities for IoT and industrial applications. It is based on the NXP i.MX95 processor, which integrates six Arm Cortex-A55 cores, one Arm Cortex-M7 core, one Arm Cortex-M33 core, an Arm Mali GPU, an ISP, and an eIQ Neutron NPU that can run at up to 2 TOPS.
-
product
4DI/4 Relay Output Modbus RTU Remote I/O
ND-6160
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
-
product
COM-HPC Server Type Ice Lake-D Starter Kit
The COM-HPC Server Type Starter Kit consists of a COM-HPC Server Type module, memory, and thermal solution of your choice with an extended ATX size COM-HPC Server Type reference carrier board, as well as necessary cabling. It allows you to quickly emulate the functionality of your end product for software development and hardware verification. Carrier board design files (schematics, mechanical drawings), COM-HPC module drivers, BSP, and user manual are also offered to aid you in designing your own custom carrier board.
-
product
COM Express Type 10 Starter Kit Plus
COM Express Type 10 Starter Kit Plus
The COM Express Type 10 nanoX Starter Kit Plus consists of a COM Express Type 10 core module reference carrier board that provides two PCIe Mini Card slots, 2 RJ-45 LAN ports, 2x USB 3.0, 2x USB 2.0, 1x USB client, 2x DB-9 COM, 1x SD card socket, and Mic/Linein/ Line-out. ADLINK also provides additional development tools including a verified 10.1" LVDS panel (optional), power supply, thermal solution and cabling accessories.
-
product
Analog Output Module
ND-6021
- Voltage Output: 0 to 10 V- Current Output: 0 to 20 mA, 4 to 20 mA- Output Isolation: 5000 VRMS- Resolution: 12-bit resolution- Accuracy: ± 0.1% of FSR (current); ± 0.2% of FSR (voltage)
-
product
Data Acquisition System
Pixie-16
The Pixie-16 is a data acquisition system for nuclear physics and other applications requiring coincident radiation detection with large number of channels.
-
product
RS-422/RS-485 Repeater
ND-6510
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
Data Acquisition and Control System
DAQ 7000
data acquisition and control system that provides connectivity, signal conditioning and modular I/O for variety of sensors or signals, and it is an ideal DAQ for field deployment.
-
product
Data Acquisition Software
TranAX 4
TranAX 4 is the universal data acquisition software from Elsys designed for the TPCX/TPCE data acquisition cards and the turnkey TraNET data acquisition instruments.- Measurement Configuration- Data Visualisation- Post Processing- Math. Calculation- Report Generation- Excel Export- Measurement Automation
-
product
32-CH 16-Bit Up to 250 kS/s Multi-Function DAQ Cards
PCI-9114 Series
ADLINK PCI-9114 series are 32-CH, 16-bit, high resolution multi-function DAQ Cards. The PCI-9114 device features flexible configurations on analog input. The devices are divided into 2 kinds: normal gain version and high gain version. Both versions provide 4 programmable input ranges for bipolar and unipolar inputs. The A/D on the PCI-9114DG device features a sampling rate of 100 kS/s with resolution at 16 bits, while PCI-9114A-DG/HG device features a sampling rate of up to 250kS/s with resolution at 16 bits. The device supports automatic analog input scanning, and offers a differential mode for 8-CH analog inputs and maximum noise elimination, as well as single-ended modes for 16- CH analog inputs. The PCI-9114 also features 1-CH 16-bit general purpose timer/counter, 16-CH TTL isolated digital inputs and 16-CH TTL isolated digital outputs. ADLINK PCI-9114 delivers cost-effective and reliable data acquisition capabilities and is ideal for a broad variety of applications.
-
product
Data Acquisition Software
GaGe provides a powerful and easy-to-use PC oscilloscope software application, GaGeScope, for use with CompuScope digitizers without the need for any programming as well as a complete library of software development kits (SDKs) for C/C#, LabVIEW, and MATLAB for custom software application development.
-
product
19” Rackmount Data Collection System
DCS-211
- Intel Atom® x5-E3930 processor- Up to 8x DI and 6x DO with two 2A relays- 3x M12 GbE, 1x RJ-45 GbE, 2x isolated RS232/422/485, 2x USB and one lockable HDMI port- Up to 3x PCI Express mini slots with one USIM card slot each- Storage: up to 64GB eMMC 5.0, 1x 2.5” SATA drive bay
-
product
NI Vision Acquisition Software
NI Vision Acquisition Software - NI LabView software for acquiring, storing, and displaying camera images.
-
product
16-CH 16-Bit 250 KS/s Simultaneous Sampling DAQ Cards
PXI-2022
ADLINK"s PXI-2022 is a simultaneous-sampling multi-function DAQ card to meet a wide range of application requirements for PXI bus computers. The device can simultaneously sample 16 AI channels with differential input configurations in order to achieve maximum noise elimination.
-
product
Data Acquisition 32 ch. Module
CPCI-AD16/16-6U
The CPCI-AD320 module provides a 6U high performance data acquisition subsystem. There are 32 thirty-two 100/200 KSPS ADC’s for maximum performance. Or an opt low cost 16 channel version. The Local DSP can be usedto simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.
-
product
Windows Driver & SDK for ADLINK PCI/PCI Express/cPCI Series Data Acquisition Cards
PCIS-DASK
ADLINK PCIS-DASK is an advanced 32-/64-bit kernel driver and 32-bit/64-bitDLL Library for custom data acquisition application development. PCIS-DASK provides a common set of Application Programming Interface (API) for ADLINK"s extensive family of PCI/PCI Express(R)/cPCI Series Data Acquisition Cards, and is ideal for custom applications development under 32-bit/64-bit Windows 7/8. With PCIS-DASK, you can easily access all functionality of ADLINK DAQ PCI/cPCI general series data acquisition cards.
-
product
COM-HPC Server Type Development Kit based on Ampere® Altra® SoC
Ampere Altra Dev Kit
Ampere Altra Dev Kit consists of a COM-HPC Server Base carrier paired with a COM-HPC Server Type Size E module and heatsink with fan. The module features Ampere® Altra® SoC (Arm Neoverse N1-based architecture) harnessing 32/64/96/128 Arm v8.2 64-bit cores for up to 1.7/2.2/2.8/2.6 GHz and providing support for up to 768GB DDR4 memory, offering unprecedented performance and power per watt with exceptional scalability.
-
product
64-Channel 1MSa/s USB Modular Multifunction Data Acquisition
U2331A
The U2331A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2331A to simulate simultaneous analog input acquisition.
