-
Product
PXI SPST Switch: 50-ch, 100Vrms/1A, Reed Relays
M9132A
-
The M9132A is a high-density, general purpose switch with50 independent, single-pole, single-throw (Form A) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100Vrms and 1A, with up to 25W power. Choose from the durable connector block or standard cable connections.
-
Product
High Voltage Micro-SIL Reed Relays
Series 119
-
The Series 119 is a range of Micro-SIL Single-In-Line reed relays intended for voltages that are beyond the capabilities of conventional SIL reed relays. The 1 Form A, 1kV version is pin and package compatible with the established and popular Series 109P.
-
Product
Micro-SIL Reed Relays
Series 109
-
SIL relays - 0.15 inch wide x 0.6 inch long package. Requires a board area of only 0.15 x 0.6 inches (3.8mm x 15.2mm).
-
Product
Micro SIL Reed Relays
Series 108
-
SIL relays - 0.15 inch wide packages. Requires a board area of 0.15 x 0.8 inches (3.8mm x 20.3mm). 10 Watts Form A or 3 Watts Form C switches in Mu-metal package
-
Product
Ultra High Density 4mm Reed Relays
120-1-A-5/1
-
Single Pole Reed Relays0.5 Amp switchingVery high packing densityStacking on 4mm x 4mm pitch1 Form A5 V Coil
-
Product
Surface Mount Reed Relays from Pickering Electronics
-
Pickering Electronics Surface Mount Reed Relays contain the highest quality instrumentation grade reed switches making them suitable for the most demanding applications and are suitable for infra-red or vapor phase reflow soldering.
-
Product
PXI High-Density Multiplexer: 64-ch, 2-Wire, 100Vrms/1A, Reed Relays
M9101A
-
The M9101A, a high-density, 64-channel PXI multiplexer routes many different channels to a single point. The switches operate in a break-before-make mode that ensures no two points are connected at the same time or, if needed multiple channels can connect simultaneously. Ideal for routing multiple analog signals to a measurement device in automated test environment (ATE) or data acquisition systems. Each channel switches a high and a low for 2-wire switching up to 100Vrms, with up to 10W of power. Connection options include the durable connector block or the standard cable connections.
-
Product
High Voltage Mini-SIL / SIP Reed Relays
Series 131
-
The Pickering Series 131 is a new range of very small Single-In-Line reed relays intended for voltages very much higher than standard small SIL relays. The vacuumed, sputtered ruthenium reed switches have a superb low level performance also, which makes them an ideal choice where a wide range of signals are involved.
-
Product
Ultra High Density 4mm Reed Relays
120-1-A-12/2
-
Single Pole Reed Relays0.5 Amp switchingVery high packing densityStacking on 4mm x 4mm pitch1 Form A12 V Coil
-
Product
High Voltage Dry Reed Relays For up to 15 kV
SERIES 62 & 63
-
ungsten switches with power rating of 50 Watts maximum? Three switch types:5kV stand-off, 3.5kV switching10kV stand-off, 7.5kV switching15kV stand-off, 12.5kV switching? Series 62 has push-on connectors on top face for EHT and solder pins and nylon studs on the underside for PCB mounting
-
Product
High Coil Resistance Reed Relays
Series 118
-
The Pickering Series 118 is a range of very sensitive reed relays that are ideal for portable electronic instruments or other applications where low power consumption and a very small footprint is important. They have 5 volt coils with a resistance up to 2200 Ohms and the option of an internal diode.
-
Product
Older Style Reed Relays from Pickering Electronics
-
The older style reed relay ranges have been manufactured for many years. Most are sold today as service replacementsproving Pickering's long term commitment to our reed relays and to our customers.
-
Product
Ultra High Density 4mm Reed Relays
124-1-A-5/2
-
Single Pole Reed Relays0.5 Amp switchingVery high packing densityStacking on 4mm x 4mm pitch1 Form A5 V Coil
-
Product
Custom Reed Relays from Pickering Electronics
-
Pickering Electronics manufactures hundreds of model relays. Many of these custom reed relays are minor variations of a standard part, for example, a different test specification or pin configuration. Others are custom designed to meet our customer's particular requirements.
-
Product
PXI SPDT Switch: 64-ch, 100 Vrms / 1A, Reed Relays
M9131A
-
The M9131A is a high-density, general purpose switch with 64 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights, or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100 Vrms and 1 A, with up to 3 W maximum power. Choose from the durable connector block or standard cable connections.
-
Product
Ultra High Density 4mm Reed Relays
122-1-A-3/2
-
Single Pole Reed Relays0.5 Amp switchingVery high packing densityStacking on 4mm x 4mm pitch1 Form A3 V Coil
-
Product
Mini-SIL Reed Relays
Series 107
-
SIL relays - Dry and Mercury wetted 0.2 inch wide packages
-
Product
PXI High-Density Matrix Switch: 4x64, 2-Wire, 100Vrms/0.5A, Reed Relays
M9121A
-
The M9121A is a 4x64 full crosspoint switch matrix offering high-density, high-speed signal switching in a single PXI module. The 2-wire matrix allows multiple channels to be connected in a single instance. Any row can be connected to any column, making it ideal for routing instrument signals to the device under test. This 2-wire switch matrix provides the high-speed, long-life reed relays to support signal switching up 100Vrms with 10W maximum power. The 4-wide bus is ideal to route signals between test instruments and the device under test. Choose from the durable connector block or standard cable connections.
-
Product
Single-In-Line Reed Relays
Series 106
-
SIL relays - 0.2 inch wide packages. Requires a board area of 0.2 x 0.8 inches (5.1mm x 20.3mm)
-
Product
CMOS Drive High Voltage SIL Reed Relays for up to 3 kilovolts
Series 101
-
Direct drive from 74HC/HCT Cmos SIL Relay. Dry or Mercury Wetted switches. 5 Volt coil for 1A dry version is 1600 0r 3000 Ohms
-
Product
PXI 50 X DPST Ruthenium Reed Relays
40-141-022
-
The 40-140A/141/143 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector.
-
Product
V-SIL Reed Relays
Series 110
-
SIL relays - 0.15 inch wide x 0.4 inch long package. Requires a board area of only 0.15 x 0.4 inches (3.8mm x 10.2mm)
-
Product
High Power Dry SIL Reed Relays
Series 114
-
SIL relays - Will replace mercury wetted relays in some applications. 1 Amp switching, 2 Amps carry. AC Mains voltage switch.
-
Product
PXI 50 Shielded SPST Reed Relays
40-142-021
-
The 40-140A/141/142/143 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector.
-
Product
SIL Reed Relays
Series 105
-
• SoftCenter™ construction• Highest quality instrumentation grade switches• Encapsulated in a plastic package with internal mu-metal magnetic screen• Wide range of switch confi gurations -Form A, 1 Form B, 2 Form A, 1 Form C• Two pole relay requires the same board area as the single pole type• Dry and mercury wetted switches are available with the same pin configuration and footprint.• Many benefits compared to industry standard relays. Learn more here >.• Insulation resistance greater than 10E12 Ohms (1TOhms) for dry Form A devices• 5, 12 and 24 Volt coils are standard, with or without internal diode• 100% tested for dynamic contact resistance
-
Product
Dual-in-Line (DIL / DIP) Reed Relays From Pickering Electronics
-
Pickering Electronics Series 97 & 98 DIL / DIP Reed Relays feature the highest quality instrumentation grade reed switches making them suitable for the most demanding applications. They are available in two ranges featuring internal mu-metal magnetic screens.
-
Product
Reed PXI 16 x SPST Reed Relay 2.5 Amp
40-136-011
-
Pickering Interfaces 40-136 Power Reed Relay Modules are suitable for applications where ordinary reed relay modules require additional current/voltage capacity. The 40-136 is suitable for voltages to 200V and current to 2.5A. Available in Normally Open (SPST & DPST) configurations. Connections are made via a front panel mounted 50 or 78-pin D-Type connector.
-
Product
PXI 25 x SPST Reed Relay 2.5 Amp
40-136-111
-
Pickering Interfaces 40-136 Power Reed Relay Modules are suitable for applications where ordinary reed relay modules require additional current/voltage capacity. The 40-136 is suitable for voltages to 200V and current to 2.5A. Available in Normally Open (SPST & DPST) configurations. Connections are made via a front panel mounted 50 or 78-pin D-Type connector.
-
Product
Single-in-Line Reed Relays
Series 112
-
SIL relays - 0.15 inch wide x 0.4 inch long package.Pins on 0.1 inch pitch - Compatible with Pickering Series 110 & 111
-
Product
Surface Mount Reed Relays
Series 200
-
Surface Mount Reed Relays. Wide range featuring dry or mercury wetted switches. Coaxial version for high speed digital or RF up to 6 GHz. 5, 12 or 24 volt coils with optional diode
