-
Product
Universal Test System
LS6601A
-
LS6601A Universal Test System is based on LXI bus, primarily used for functional electronic product or system verification, test parameters. Because the system design is based on LXI bus structure, so its addition to general characteristics of versatility, scalability, but the architecture of the system more flexible, the test system is not limited to one or more cabinets, but may be needed test network and multiple LS6601A and can be easily grouped into one or more of the ground test system, depending on the test mechanism, form a powerful set of test, control, simulation, simulation, data management as one; distributed in different places .
-
Product
Photoelectrochemical Test System
ModuLab XM
-
The system, based upon Solartron Analytical's world-leading experience in transfer function measurements, offers a high-quality measurement platform for characterizing a range of photoelectrochemical devices such as DSSC's, Perovskite cells, and Photoanodes," noted Professor Laurie Peter, world leading expert, University of Bath, UK. Professor Peter acted as scientific advisor during the development of the ModuLab PhotoEchem system and helped ensure the system met the requirements of the most demanding photovoltaic researchers in the market today.
-
Product
Short Circuit Test System
-
Shanghai Guantu Technology Co., Ltd.
The short-circuit test system refers to what kind of short-circuit test is carried out by which equipment, and how long is the test time. But I have one thing to tell you, the short circuit test is a kind of destructive test, mainly to test the working condition of the used equipment in a crisis situation, or to test how strong the anti-destructive ability of the used equipment is. Just like a lot of equipment in the military must undergo a short-circuit test, some for 3 minutes or longer, in order to resist breaking calls against the enemy during wartime.
-
Product
Drive-Train/Power-Train Performance/Endurance Test System
-
This system is suitable for engine drive test or transaxle test of HEV/EV in combination with the real-time model calculation by the measurement/control panel and low inertial motor. Simulation test of an actual vehicle running condition can be executed by modeling a real tires or an engine. The tires and vehicles are modeled by MATLAB® / Simulink®, so they can be evaluated under various conditions by changing parameters or replacing models.
-
Product
System Level Test and Burn-in Solutions
-
System Level Test (SLT) is a paradigm shift from traditional structural and functional testing. The device is tested in a complete, integrated system to evaluate its compliance against specified requirements. The system approach allows for higher and more cost-effective test coverage especially for multi-function and non-deterministic devices. It also brings new integration and test challenges like: ..Designing test fixtures on Burn-in Boards with system components ...
-
Product
Brake Test Systems
Giant 8000 Series
-
Customer perception of vehicle quality is closely related to the NVH behaviour of the vehicle. With the HORIBA ATS Brake testing system, NVH relevant design features are analyzed and various metrics stored in the database of the automation system. For friction borne vehicle NVH problems coming from the brake and its components the GIANT 8000 Series is the ideal tool to resolve it. The GIANT 8000 Series is superior NVH test system providing you with the best testing conditions for all types of vehicles. Test brake fixtures could be tested with a complete wheel suspension system. In a semi acoustic chamber NVH tests could be realized and drum brakes and disc brakes including the vehicle axle could be tested.
-
Product
CPE Design Verification System
Jupiter 310
-
Jupiter is the industry standard for automated DOCSIS physical (PHY) layer testing. It provides the most comprehensive test coverage and accurate results on the market for DOCSIS 3.1 devices.
-
Product
Edge AI Inference Systems
-
Powered by NVIDIA Jetson family and RTX, AIR series provides scalable AI inference performance or efficient retraining on a large scale at the edge.
-
Product
Pressure Decay Test Systems
-
Pressure decay leak testing technology has become a mainstay in the arena of high volume production testing. Pressure decay testing methods offer the world's manufacturers a cost-effective and easily applicable solution to the leak testing challenges they encounter on a given day. Fundamentally, pressure decay testing is a straightforward measurement technique; Cincinnati Test Systems (CTS) pioneers new and innovative ways to integrate our technology into custom turnkey systems that exceed the industry standards for reliability and repeatability. CTS' 30+ years of experience goes way beyond the pressure test unit by offering our customers comprehensive, custom turnkey solutions to the most challenging leak testing problems.
-
Product
EW System Test Set
MS 1107
-
PSS LRU Test Set is used to test the RWR (Radar Warning Receiver) system by simulating the input signals and testing the output signals.
-
Product
PXI - Test System
-
We provide a complete PXI test system made by PXI individual components: 19'' rack, Measuring and stimuli cards, Relay cards, Power Supplies, Integration additional protocol cards such as CAN and CANopen, Boundary Scan, Integration of additional test hardware
-
Product
Residential Meter Test System
RADIAN RM-17
-
The Radian Research RM-17 Residential Meter Test System offers simplicity for testing residential watthour meters. In a compact, lightweight package of 7 pounds, the RM-17 delivers accuracy and flexibility in a practical solution to watthour meter testing. The RM-17 combines simple operation, advanced data management, and exceptional accuracy to provide a cost effective approach to field testing.
-
Product
Nanomechanical Test System
Hysitron TS 77 Select
-
The Hysitron TS 77 Select automated benchtop nanomechanical and nanotribological test system provides the highest level of performance, functionality, and accessibility of any instrument in its class. Built around Bruker’s renowned TriboScope capacitive transducer technology, this new test system delivers reliable mechanical and tribological characterization over nanometer-to-micrometer length scales.
-
Product
Wireless Connectivity and IoT Test System
IQxel-M4W
-
Suitable for the lab or manufacturing environment, the IQxel-M4W 6G is ideal for RF testing of wireless connectivity and IoT products. The platform’s flexible software supports the most prevalent wireless connectivity standards: WLAN 802.11ax (Wi-Fi 6) and legacy (802.11a/b/g/n/ac), Bluetooth® Classic and Low Energy (Bluetooth® LE) as well as Zigbee/Thread, Z-Wave, LPWAN technologies (Sigfox, LoRa) and cellular IoT technologies (NB-IoT, LTE-M, 5G) as well as navigational technologies.
-
Product
Hydrostatic Test Stand, Hydraulic System Components
9901HTX-100LR2-72x24x12
-
The 6 foot wide Hydrostatic Test Stand, Hydraulic System Components is utilized for pressure testing hose and tube assemblies as well as any component requiring hydrostatic testing in the integral safety test chamber.
-
Product
Generator/Analyzer for NFC/EMVCo Manufacturing Test
Micropross MP500 PT1-NFC
-
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
-
Product
Surge Voltage and Surge Current Testing Systems
-
HIGHVOLT Prüftechnik Dresden GmbH
Pulse Voltage Test Systems are used for surge testing on transformers, cables, gas insulated switchgear (GIS), arresters, and other high voltage equipment.
-
Product
Temperature/Humidity Vibration Test Systems
EHVC SERIES
-
The EHVC Series is designed for highly accelerated life testing, the demand of which from customers is increasing today. This is a joint system of the AGREE chamber and thermal shock chamber that we have manufactured and makes the temperature rate up to 20℃/min feasible with a compressor only. With this feature, the highly accelerated life test such as AGREE tests, most thermal shock tests can be performed with one unit.
-
Product
Pneumatic Vertical Shock Test System
KRD11 series
-
KRD11 series pneumatic vertical shock test system is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and bump test, can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests.
-
Product
Tan Delta Test System
-
Diagnostic test that indicates the degree of cable insulation degradation. Rather than using only a VLF instrument to perform a go/no-go proof test, the Tan Delta, used in conjunction with a VLF hipot, permits the user to grade the deterioration level of many cables in order to prioritize replacement, rejuvenation, or to determine what additional tests may be useful.
-
Product
PCI / PMC / CompactPCI Test System
PCITS
-
The CPCI850 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
Partial Discharge Test System
TPP
-
The Partial Discharge Test System type TPP is used for non-destructive insulation and quality testing of electrical components (for example according VDE 0110-1, EN 50178, IEC 60270 and IEC 60060).
-
Product
High Voltage DC Cable Test Systems
-
We can offer from ±18kVdc to ±30kVdc units which all have automatic earthing for discharging capacitive loads. They are designed to perform tests on installed cables and jointing systems.
-
Product
Microtester Test Systems
-
With the micro probes and the fine-pitch adapters used on them, you are able to contact the finest test structures. E-tests, functional tests, IC tests or high-current tests are made to be affordable, efficient and with a short cycle time. With the integration of HF adapters we also enable the double-sided testing of HF substrates up to high frequency ranges.
-
Product
Measurement System For Testing & Binning Of Back-End LEDs
TP121-TH
-
The photometric specifications of LEDs must meet very high tolerance requirements regardless of whether they are to be used in general, automotive or other specialist lighting applications. This is often a problem since the manufacturing tolerances of LEDs can be higher than those permitted in the end-use applications. Also, LED binning by LED manufacturers in order to classify LEDs based on their tolerances is performed with flash mode testing using pulsed current flow. However, end-use applications of the LEDs often operate in constant current mode and with significant thermal effects. The sophisticated LED processing industry therefore requires measurement devices that can be used for both manufacturer-compliant pulsed mode, as well as constant current operation mode. When the LEDs are run in constant current mode, the junction temperature has significant influence on the performance and lifetime of the LED. Therefore, test systems should be able to test the LEDs at specific junction temperatures.
-
-
Product
Low Resistance Test System
9100-2
-
Palico Instrument Laboratories
The Model 9100-2 measures the resistance of single or multiple battery separators quickly and accurately when used with our Model 9000-9100 Electrolyte Test Bath. This system uses a 4-terminal measurement technique which cancels the effects of electrode/electrolyte potentials.
-
Product
Precision Multiferroic and Ferroelectric Test System
-
The Precision Multiferroic tester is Radiant's most advanced test system. The Multiferroic has fast built-in frequency at 30kHz measurements using the 200V internal amplifier and 50kHz measurements using the 100V internal amplifier. This system comes in a built-in option of +/-100V, 200V, and 500V and can be expanded to 10kV. This unit also comes with a 18 bit ADC and requires no configuration changes.
-
Product
Modular Test System
-
A modular test system, RTS (real time scanner) provides instant test results with minimal interface cables to check wiring during installation.It tests wire harnesses in real time using our micro switching technology, reducing the need for high cost interface cables by around 90%. an innovative best-in-class solution for FAL testing, RTS also offers many benefits for wire harness and sub-assembly manufacturers.
-
Product
E-mobility Test Systems
-
Correct contactingcharging cable detectionsecurity questionExtensive range of accessories for on-site measurements in a separate caseCharging cable with additional measuring lines (Sense)Convenient control through guided test procedure via WinSAM and tabletElectromechanical locking
