-
Product
Coupler And Decoupler Used With Lightning Impulse Simulation Tester
-
All electric equipments & systems is required Impulse Simulation Test to the to be tested under the condition where the power source is applied to the product-under-test.At this test condition, the decoupler is needed to reduce the impulse flowing through the power line while testing. And the coupler which is inserted between tester and product, to simulate the actual condition, so the electric circuit of decoupler is prescribet by IEC rules.
-
Product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
2-CH MIL-STD-1553A/B Bus Simulator Module
1553 WA73A-455
-
The WA73A-455 MIL-STD-1553A/B Bus Simulator Module allows a system controller in an ATE system to communicate with and test devices that conform to the MIL-STD1553A/B data bus used in military aircraft and communications systems. Each of the WA73A-455's two channels operate as two separate and independent channels with their own VXIbus logical address, interrupts, and complete set of controls and indicators. As a result, each channel of the WA73A-455 is truly an independent instrument, and, therefore, individually programmable.
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI Express
PCIe-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Circuit Breaker & Control Cabinet Simulator
SIM-CB6
-
The SIM-CB6 is the circuit breaker simulator that will make you an expert in breaker testing. The SIM-CB6 enables you to simulate any type of circuit breaker (SF6, Air Blast, Oil, etc.) up to 6 contacts (2 contacts per phase), with or without closing/opening resistor contacts and control cabinets. This simulator will allow you to increase your knowledge on circuit breaker analyzer systems to ensure full efficiency once on the field.
-
Product
Ethernet Test and Simulation Instruments for Speeds from 10 Mbit/s to 25 Gbit/s
-
Avionics Interface Technologies
AIT’s Ethernet test instruments provide Ethernet test features for 10Mbit, 100Mbit, 1Gbit, and 10Gbit Ethernet networks, for both Optical and Copper media. All instruments are supported by Analyzer and Simulator software applications (GUIs) and additionally software API’s allowing integration into user applications.
-
Product
Au Truck / Bus Fleet Management System (FMS) Simulators
-
The Au Truck / Bus Fleet Management System (FMS) simulator can generate Controller Area Network (CAN) signal per Truck FMS Standard (Vers. 02.00) and Bus FMS Standard (Vers. 00.02). Au FMS simulators are designed very easy to use. All editions can run independently (without personal computer). Au FMS Simulators are widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration, to product development and product validation.
-
Product
Mechanical Simulation in Matlab
-
There are variety of numerical possibilities in the MATLAB and Simulink simulation environment. For those simulation environments we offer you various toolboxes that allow you to perform simulations easily and efficiently. These toolboxes can be combined with all available ways of MATLAB and Simulink. Our toolboxes can provide you support in the following areas: Analysis of structural dynamic behavior, Vibration and noise abatement, Design of active systems, Model Reduction, Ansys-Matlab interface.
-
Product
Tailor-Made to Simulate Low-Temperature Plasma Sources and Systems
Plasma Module
-
The Plasma Module is tailor-made to model and simulate low-temperature plasma sources and systems. Engineers and scientists use it to gain insight into the physics of discharges and gauge the performance of existing or potential designs. The module can perform analysis in all space dimensions 1D, 2D, and 3D. Plasma systems are, by their very nature, complicated systems with a high degree of nonlinearity. Small changes to the electrical input or plasma chemistry can result in significant changes in the discharge characteristics.
-
Product
VectorPro - Simulation Cyclizer for VCD to WGL/STIL
VectorPro
-
VectorPro is a low-cost, intuitive test development tool used to translate VCD/EVCD simulations into cyclized ATE Test Vectors in either WGL or STIL formats. This highly versatile tool reads in both VCD and EVCD formatted design simulations, and through the use of its flexible GUI, users are able to view and modify the simulation to fit the needs of their Test Environment.
-
Product
Single Or Dual Stream MIL-STD-1553A/BTest And Simulation Module For Standard Ethernet
ANET1553-x
-
The ANET1553-x is a member of AIM’s new line of Ethernet based modules for analysing, simulating, monitoring and testing MIL-STD-1553A/B databuses. For wireless applications, an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
Product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
-
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
Product
Complex Environment Simulator
-
Complies with IEC60904-9 solar simulator/classes B and C. Includes integrated temperature and humidity controls, allowing the output measurement testing and the complex durability testing to be conducted by one unit. The work size and the temperature/humidity control range, etc. can be customized.These chambers are available at Iwasaki for testing your samples; please contact your local agent for details.
-
Product
Calibration Cable, 78-pin D-type, Thermocouple Simulator Modules
40-975-078-1m
-
This cable assembly is specifically designed to connect to the 78-Pin D-Type port on the front panel of Pickering Interfaces Thermocouple Simulator Modules 41-760 and 41-761 enabling calibration via an external DMM.
-
Product
4, 8, 16 Or 32 Channel ARINC429Test And Simulation Modules For XMC
AXC429-x
-
ARINC429 Test and Simulation module for XMC with 4, 8, 16 and 32 programmable Tx/Rx channels plus up to 8 Discrete Inputs/8 Discrete Outputs which can be monitored or generated.
-
Product
2 Port 4GFC Fibre Channel ARINC818 Test, Simulator and Monitor Module For PCIe
APS-FC-2
-
The APS-FC-2 is AIM’s high performance PCIe module offering 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The APS-FC-2 is a powerful State-of-the-Art 4-lane PCIe 2.0 compliant PCIe board.
-
Product
Full 4-Quadrant Grid Simulator
TC.ACS
-
The increasing number of alternative power sources like solar, wind driven or biological energy systems call for consistent and well demanding regulations for energy feed into the utility grid. Manufacturers of such systems have to test and to prove the compliance of their equipment. Grid simulators form an electronic equivalent circuit for the grid, but allow to vary all relevant parameters in order to test the behaviour and response of the equipment under test.
-
Product
Dynamic Test Board Vehicle Simulator
DTB
-
The Dynamic Test Board vehicle simulator range enhances functional testing by allowing greater test depth before the prototyping stage.
-
Product
Monitoring Solar Panel Strings, DC 30A, Φ6mm
CTF-6DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Compact, Space-saving, Low Cost DC Current Sensors.・Split-core type, easy to apply to existing circuit.・Easy to use by unipolar +5V power supply.・High speed responsibility – less than 10μsec. 0 rated primary current.・Suitable for monitoring solar panel strings.
-
Product
Solar Analyzers
-
Max. solar system power (Pmax) search by Auto-scan: 1000V, 12A (12000W capability)The analyzer and the Remote Solar Detector is connected by Bluetooth wireless communication (Bluetooth 2.1 + EDR Class 1)The Remote Solar Detector is moisture-proofIntelligent test logic with no personnel attendance required in the field Solar system analyzer waits and tests the system until appropriate sunlight irradiance is detectedMax. voltage (Vpm) at Pmax, Max. current (Ipm) at Pmax Voltage at open circuit (Voc), Current at short circuit (Isc)Efficiency (%) calculation of solar systemTemperature measurement of solar panelsIrradiance measurement of sun lightSeries resistance (Rs) calculation of solar panelsWith data logging/open function, the I-V curves of solar system can be analysed / recorded for a period of time (e.g. 60 min.)Conversion of I-V curve under OPC to data under standard test condition (STC) based upon IEC standardProvide Operating Condition (OPC) and Standard Test Condition (STC) test reports for verification of solar panel performance (OK or NO OK)Users can set up the parameters of solar panelsUsers can set up the series number of solar panels. Parameters of many solar panels can be measured in one measurementThe Irradiances and Temperatures of solar panels can be continuously measured, monitored and recordedContinuously measure/monitor/record the DC power output of solar system and the AC power output of inverter (1 phase or balanced 3 phases)Calculate the efficiency of DC to AC power conversion and the efficiency of the max.output power
-
Product
IMU MODELING AND SIMULATION
-
CAST Navigation’s INS systems provide high rate inertial data with exceptional fidelity to support the integration and testing of today’s complex EGI and GNSS/INS navigation systems. The CAST system is designed for optimal performance when the inertial sensor and GNSS receiver are either loosely, tightly or ultra-tightly coupled, or when an INS aiding source can be utilized by any other type of device.
-
Product
Sand Dust Climatic Environmental Simulation Test Chamber
CX-SC80
-
Shenzhen Chuangxin Instruments Co., Ltd.
Sand Dust Climatic Environmental Simulation Test Chamber
-
Product
Cycle Voltage Drop (Rise) Simulator
STT-CSS-20P1
-
Beijing KeHuan Century EMC Technology Co,.LTD
*Using 2 The regulator, and the rated voltage adjustable automatic voltage regulator, power fluctuations avoid adversely affecting the test results. Simulate the test under 110V power supply. It can simulate the fluctuation of the power grid under extreme conditions (such as high or low power supply voltage in remote areas).
-
Product
MIL-STD-1553 A / B Test And Simulation VME Module
VME-1553
-
*Dual redundant*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*VISA based VXI Plug & Play driver*Optional twinax front end
-
Product
Simulation Systems
-
Bloomy offers Simulation Systems for Hardware in-the-Loop (HIL) and open loop test of electronic controls and mechanical actuators for all types of transportation and defense systems including aircraft, rail, automobiles and ships. These systems, now deployed at major aerospace, locomotive and military manufacturers and research facilities worldwide, provide world-class, high-fidelity simulated environments for use in both closed-loop and open-loop testing. Because Bloomy’s Simulation Systems are largely constructed from COTS components, time to first test can be reduced significantly, and their highly-customizable nature allows your test system experts to provide your unique IP to differentiate your product from your competitors.
-
Product
3U VPX RL Thermal Load Simulation Module
-
The 3U power test module is an ideal solution for evaluating heat dissipation in a rugged conduction cooled VPX cage or chassis. This card is a thermal load in the chassis to evaluate the heat dissipation. The chassis can be monitored with temp sensing probes and or FLIR imaging. Different wattages are selected by setting dip switches. The +5 and 3.3V loads are on the top of the module. The +12V and -12V loads are on the bottom side of the module.
-
Product
Simulation and Model-Based Design
Simulink
-
Simulink is a block diagram environment for multidomain simulation and Model-Based Design. It supports system-level design, simulation, automatic code generation, and continuous test and verification of embedded systems. Simulink provides a graphical editor, customizable block libraries, and solvers for modeling and simulating dynamic systems. It is integrated with MATLAB, enabling you to incorporate MATLAB algorithms into models and export simulation results to MATLAB for further analysis.
-
Product
Simulation Transport Vibration Table
CX-M120
-
Shenzhen Chuangxin Instruments Co., Ltd.
CX-M120 Simulation Transport Vibration Table was applicable to toys,furniture,gifts,cera-mics,packaging and other products to simulate the transport tests.Comply with the U.S. and European transport standards and have characteristic with low noise,reasonable structure,durable,etc.Basic Standard:Following The EN.ANSI.UL.ASTM.ISTA International Trans-port Standard.
-
Product
1, 2, 4 Or 8 Stream MIL-STD-1553Test And Simulation Module For VME (6U)
AVC1553-x
-
MIL-STD-1553 Test and Simulation module for VME (6U) with 1, 2, 4 or 8 dual redundant channels.Integrated modular solution by using the AMCX1553-x PMC cards installed on AIM’s AVC-2 Generic VME64x (6U) Carrier card.
-
Product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
