-
Product
Leakage Current Sensors / Small Current Sensors
-
ChenYang Technologies GmbH & Co. KG
This current sensor is based on magnetic modulation and compensation principle, and can beused for measurement of small DC current and leakage current, current difference between two ormore conductors.
-
Product
Voltage and Current Amplifier
CMS 356
-
The CMS 356 is a voltage and current amplifier for analog low-level signals provided by a CMC test set or by any other signal source, such as a digital real-time power system network simulator. When used in combination with a CMC test set, the amplifier extends the capabilities of the test set to provide additional output channels and higher amplitudes.
-
Product
Fully Automatic Eddy Current Crack Test System
ROTO-PUSH
-
Foerster Instruments, Incorporated
The ROTO-PUSH test station, which is integrated in production lines, serves to test cylindrical components for cracks in the liner surface. The testing configuration has to be rotated for automatic crack testing. After the test, the test pieces are sorted and separated. The continuous test run ensures a high testing rate, which increases profitability.
-
Product
High Current Sensor
HCS-BTA
-
Vernier Software & Technology, LLC
Use the High Current Sensor in experiments that involve currents larger than 1 A, such as solar panels, hand generators, and other alternative energy projects.
-
Product
Primary Current Injection Testing
KAM
-
This substation testing device is designed to grant high current output when needed in substation commissioning activities.
-
Product
Current Differential and Overcurrent Relay
SEL-387
-
Schweitzer Engineering Laboratories, Inc.
Protect and control any two-, three-, or four-winding power transformer with the SEL-387, which provides thermal and through-fault monitoring, and with SELogic Control Equations, can detect breaker failure.
-
Product
Low Input Bias Current Op Amps (≤100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
Voltage And Current Calibrator
-
Precision Mastech Enterprises Co.
A precision instrument designed to generate (source) and measure precise electrical signals.
-
Product
DC Resistance and Current Measurement System
-
DC Resistance and Current Measurement System including: 6622A Series Bridge, 6634A Temperature Stabilized Resistance Standards, 6664C Scanner(s), world’s most precise and stable 6623A Precision Current Source/Range Extender, Wired Equipment Rack, and Bridgeworks Software.
-
Product
AC/DC Current Probe (2-Channel), 3 MHz, 50 UA
N2820A
-
The N2820A 2-channel current probe connects to two oscilloscope channels to provide simultaneous low- and high-gain views for wider dynamic range measurement, while the N2821A 1-channel current probe provides one user-selectable view at a time.
-
Product
For Overhead Distribution Line Current Tester With Power Flow Direction Record
MHR-600
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Measuring and recording the average current values & power flow directions in the setting interval.・Easy to use, as an indirect hot-line work tool.・Memorized data can be outputted to USB memoryafter measurement.・For 6.6KV circuit, protection level IP64.
-
Product
Current Clamp Multimeters
-
PeakTech Prüf- und Messtechnik GmbH
It uses a pair of jaw which allow clamping around an electrical conductor to measure the current in a conductor without the need to make physical contact unlike a normal multimeter.
-
Product
Hall Effect DC Current Sensor
CYHCT-L20K
-
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-L20K is based on open loop principle and designed with a high galvanic isolationbetween primary conductor and secondary circuit. It can be used for measurement of DC current, DCpulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
32CH 4-20mA Current Sink Card
SET-1250
-
Each channel provides an isolating relay and a short-circuit MOSFET with which opening and short-circuit errors can be simulated. The short-circuit MOSFET has overcurrent protection with integrated current limitation.
-
Product
AC/DC Current Clamp Meter
CM600
-
Clamp opens up to 1 inch (25.4 mm). One rotary switch operation. Large 4 digit LCD display. AC/DC Voltage measurement up to 600 Volt. AC/DC current measurement up to 600 A.Relative measurement. One touch auto zero.
-
Product
Transformer Test Equipment
-
KV Hipot Power Test Equipment Co.,Ltd
Transformer Test Equipment. Ensure that a transformer meets performance and reliability requirements, from the production line to after a repair or upgrade, when a major disruptive event occurs such as a lightning strike, or for preventive/predictive maintenance.
-
Product
Through Hole type AC Current Sensor
CT-6K
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
For measuring current generally (through hole type)
-
Product
Eddy Current Probes and Drivers
-
Proximity sensors work on the eddy current principle. A proximity system consists of an eddy current probe, extension cable and driver. A high-frequency RF signal is generated by the driver, sent through the extension and probe cables and radiated from the probe tip. The tip consists of a precision wound copper coil inside a chemical and temperature resistant PEEK case.
-
Product
FaithTech Ultra Low Voltage And High Current DC Load
NZ/N Series
-
Shenzhen FaithTech Technology Co., Ltd.
Ultra low voltage and high current DC electronic load is a high reliability and high performance electronic load product derived from FT conventional electronic load for low voltage and high current test scenarios such as fuel cell test and CPU power supply device test. For different current levels, this product includes two series: NZ and N. The voltage is 0-20V or 40V, in which the NZ series can be loaded with 0V full current, and the N series can be loaded with ultra-low voltage and full current. The load capacity is up to 0V@1200A and 0.2V@5000A . This series of products has high precision and high cost performance, which is your good choice for testing.
-
Product
Multiparameter Current Meters
MIDAS ECM
-
The MIDAS ECM is one of only a few multiparameter current meters that allow real-time operations over several thousand metres of cable, as well as autonomous deployment.
-
Product
Multi Channel Linear Vibration Motor Current Isolation tester
BK2017
-
The BK2017 Current and Isolation Tester was designed as a single purpose machine for quickly testing up to 8 linear vibration motors at a time. You can test current and isolation without checking other characteristics of the motor. With its simple design, it is very easy to use and the results appear clearly on the screen in about half a second. And with only 2 cables to connect, it can quickly be plugged into an automatic loader/sorter for even faster results!
-
Product
Leakage Current Tester
-
Test Voltage : - 1V to 500V DC settableAccuracy : ± 1% of set Value ± 1digitLeakage Current : - Accuracy - ± 0.5% ± 1digitDigital Model – 19.99μA / 199.9 μA / 1.999mA / 19.99mAAnalog Model - 10μA /25μA/100 μA/1mA/2.5mA/10mASeparate Indication for Charge / Measure and Discharge modeAvailable in Digital Version Also
-
Product
Split type Pulse Current Sensor
PCT-06
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Through hole type pulse current sensor.*Pulse current sensor for power demand meter.
-
Product
Complete Transformer Test Bench
-
Weshine Electric Manufacturing Co., Ltd
Our multifunction Transformer Test Bench (VS-ZHSY Series) is intuitive with all of the ease of working with individual, dedicated instruments. We deliver this experience through our design philosophy. Rather than producing a single, complex system with afterthought towards rendering it friendly, we uniquely combine several intelligent instruments packaged as a single system.
-
Product
SpikeSafe DC / Continuous Pulsed Current Sources
-
The Vektrex SpikeSafe™ DC / Continuous Pulse (DCP) Current Sources provide reliable DC or pulsed drive for LED or laser diode reliability testing, IESNA LM-80 maintenance testing, and other test applications requiring DC or continuous pulse current. Models support currents from 500mA to 60A and compliance voltages from 50V to 400V. All models feature individual channel control, accurate pulsing over long output cables, precise current, precision pulsing for improved measurement repeatability, and high power density — typically 6.4kW-8kW.
-
Product
Current Measurements Of PWM Or Inverter, AC/DC 1～50A, Φ16mm
CTF-50DC-U24V
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 1～50A*Current measurements for PWM or inverter
-
Product
Current Digital Set Point Relay
-
These Digital set point relay for current (type mrd2011-a) are field proven with excellent sensitivity and are with two independent outputs and are used as under current and over current controlling operations. The two independent outputs are programmable in a specific range i. E. The range if it is 25a the settings can be made within the range of 250 a. This facility of having the liberty to set the required current is added advantage in the digital meters of these models available in the market. The set points are field settable within the range mentioned in the model. these relays have inbuilt timers and this facility enables the user to avoid external timers and external wiring. The timers are programmable from 0 second to 20 seconds. The ranges available are up to 2500 a. The dimensions are compact and are of 96 mm x 96 mm x 65 mm only. The auxiliary supply for the relay is 110v ac or 230v ac.
-
Product
Current Measurements of PWM or Inverter, AC/DC 10～200A, φ24mm
CTF-200DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 10～200A*Current measurements for PWM or inverter
-
Product
Transformer Bench Tester
KVBT
-
KV Hipot Power Test Equipment Co.,Ltd
Transformer Test System is applied for ex-work and maintenance detecting on various transformers.
-
Product
PXI/PXIe Wide Current Range Multiplexer Module, Single 6-Channel, 4-Pole
42-514-102
-
The 40-514-102 (PXI) and 42-514-102 (PXIe) are low density multiplexers in single 6-channel, 4-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
