-
Product
Portable Power Amplifier
PAV120Bip
-
PAV120Bip（6*120V） is the portable type power amplifier which is specially designed for R&D of power system simulation. It is with linear type amplifier design so that it could be adapted to simulation experiment which may include various capacitive and inductive load.
-
Product
Motion Control Terminal Board For Panasonic MINAS A4 Servo Amplifiers
DIN-814-A40
-
- Panasonic MINAS A4 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
R&D
-
Scientific Computing International
A term to describe the effort a company devotes to the innovation, and improvement of its products and processes.
-
Product
Saluki SE2041 DSP Lock-In Amplifier
-
SE2041 Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 60 MHz. With the advantage of the latest digital signal processing technology and high-speed 250MSPS 14-bit ADC, SE2041 can easily detect the phase and the magnitude of weak signals overwhelmed by various large noises. The performance of SE2041 is as good as other lock-in amplifiers all over the world, even better than them in some certain parameters, such as measurement accuracy, SNR, dynamic reserve, which meets the needs of scientific research and industrial application well.
-
Product
Amplifiers
-
We have designed and manufactured amplifiers using all major semiconductor materials, LDMOS, GaN, GaAs, and InP, to produce narrow, wideband, and pulse, receive and transmit amplifiers from 1 MHz to 220 GHz and power levels from mW to over 10 kW.
-
Product
Limiting Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink's limiting amplifiers use FET device with good consistency and distributed traveling wave amplifying circuit to design. Good amplitude and phase consistency characteristics can be achieved in a wide input dynamic range. It's the key component of the electronic system. Keylink's limiting amplifiers can be categorized as follows.
-
Product
24" Solid Fixed Storage Shelf, 20"D
SS-2420
-
Sturdy 24" shelf formed of one piece of 16 ga. CRS bolts to panel mounting rails. Supports heavy chassis or power supplies or provides storage for tools, test leads, chart paper, etc.
-
Product
E-Band Low Noise Amplifier MMIC
AWL-7186
-
The AWL-7186 is a 4-stage ultra-low noise amplifier that provides a noise figure of less than 3.5 dB, an output P1dB of +8 dBm, and an adjustable gain range of 15 dB. The MMIC features exceptional gain flatness and superior noise performance over a very wide bandwidth. It is implemented in 0.1 um GaAs PHEMT technology.
-
Product
19" Rackmount Drawer, Unshielded, 3.5"H x 20"D
DR-031920
-
Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Zero-Drift Op Amplifiers
-
The zero-drift amplifiers from Analog Devices combine both auto-zero and a chopper to self-correct continuously for dc errors over time and temperature, enabling the amplifier to achieve microvolt-offsets and nanovolts per degree Celsius drift. By design, the zero-drift amplifier has no 1/f noise nor does it suffer from long-term drift.
-
Product
Low Noise Amplifiers for Radio Amateurs
-
Our Low Noise Preamplifiers are remarkable for extremely low noise, excellent SWR, high efficiency and a high IP3. The Low Noise amplifiers are especially selective and absolute stable therefore oscillation is avoided. Even if you have a bad SWR. This is the reason why radio amateurs and club-stations all around the world trust in Kuhne electronic equipment. The products are perfect for use in contests, EME, MeteorScatter, Aurora and Tropo DX. Small mechanical measurements and technical innovations from the professional sector, e. g. milled aluminium cases, enable high temperature stability and tower mounting. Numerous contest victories, records and first contacts with a country were and are achieved with Kuhne products. Don't compromise and get technology from Kuhne electronic!
-
Product
Communications/Data Link Amplifiers
-
Amplifiers specific to the Communications systems include a wide range of Solid State Power Amplifiers (SSPAs) and Low Noise Amplifiers (LNAs) originally from Paradise Datacom and a range of organically developed products within TMS. Satcom SSPAs are considered a core competence of Paradise Datacom's product line who have invested heavily in converting it's complete amplifier offering from GaAs to GaN from C-Band all the way to Ka-Band.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type D, Ø0.80mm, 155gf
K100-D080155-SKAU
-
K100 Series, Pitch 100mil, Tip Style D, Tip Diameter Ø0.80mm, Spring force 155gf, Steel with Gold Plating.
-
Product
Low Noise Amplifiers
-
RPG Low Noise Amplifiers are developed and manufactured using the most modern discrete components and thin film technologies, in order to cover the frequency range 50 to 350 GHz. With improved DC-supply and modern semiconductors these amplifiers not only deliver low noise performance but also broad operating bandwidth and gain flatness. These low-noise amplifiers are available as a standard product and on request as customized manufactured product.
-
Product
Linear Amplifiers
LA Series
-
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
Product
30"D Retractable Writing Shelf for 24" Racks
WS-022430
-
24" x 30"D retractable writing shelf operates smoothly on ball bearing slides which lock in fully extended position.
-
Product
Transimpedance Amplifiers
-
Current-to-Voltage Amplifier for use with Photodiode-Based Detectors. Transimpedance Amplifiers, Standalone Devices with Data Acquisition as well as Display Function (Optometer). Log/Lin Switching Amplifiers, etc.
-
Product
Audio Amplifiers
-
An electronic device that increases the strength (amplitude) of audio signals that pass through it.
-
Product
Time & Frequency Distribution Amplifiers
-
Brandywine offers a wide range of high quality, state of the art signal timing distribution amplifiers, all with very low phase noise. These precision timing signal distribution amplifiers offer a variety of time and frequency signals and interface formats including IRIG A, IRIG B, Have Quick, 1PPS, as well as low phase noise reference frequencies. All of our distribution amplifiers feature dual inputs with automatic failover and multiple independently buffered outputs.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type D, Ø0.80mm, 230gf
K100-D080230-SKAU
-
K100 Series, Pitch 100mil, Tip Style D, Tip Diameter Ø0.80mm, Spring force 230gf, Steel with Gold Plating.
-
Product
Waveguide Amplifiers
-
VDI offers waveguide amplifiers for various applications. Waveguide amplifiers are able to boost a small input RF signal to a large output RF signal. For sample data on waveguide amplifiers, please refer to the Waveguide Amplifier Product Manual (also located under Resources). Please contact VDI for more information.
-
Product
Digital Shore D Rubber Hardness Tester
HS-D
-
Shenzhen Chuangxin Instruments Co., Ltd.
HS-D is a digital Shore D type durometer. It is suitable for hard plastic (such as thermoplastic, hard resin, nylon, and organic glass, etc.), hard rubber, and other related chemical products(such as anti-corrosion coating materials, flame retardant materials, paint, etc.)
-
Product
Single-Ended SD Video Filter Amplifier With Output Short-To-Battery Protection
ADA4432-1
-
The ADA4432-1 is a single-ended output fully integrated video reconstruction filter that combines overvoltage protection (short-to-battery [STB] protection) and short-to-ground (STG) protection on the outputs, with excellent video specifications and low power consumption. The combination of STB protection and robust ESD tolerance allows the ADA4432-1 to provide superior protection in the hostile automotive environment.
-
Product
Low Noise Amplifiers
-
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a variety of applications but are primarily suited to airborne, maritime and ground based radar systems. LNAs are primarily intended to minimise added noise whilst providing high gain so design focusses on the parameters associated with the noise response of the amplifier. They are usually the first amplifier in the Radar detection chain and will have the lowest noise figure.
-
Product
20GHz 30dBm RF Signal Amplifier
A10200
-
Model A10200 is an ultra-small footprint, ultra wideband, high power amplifier designed for high frequency, high power, signal amplification. With an ultra high bandwidth of almost 20GHz and up to +28dBm power into 50 ohms, the A10200 is the ideal complimentary amplifier to any signal source that needs an extended power boost for demanding applications.
-
Product
24" Rackmount Drawer with Keylock, Unshielded, 8.75"H x 30"D
DR-082430-K
-
Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Erbium Doped Fiber Amplifier
EDFA
-
EDFAs are based on the light amplification in erbium-doped fiber, which are optically pumped by means of 980 nm or 1480 nm light sources. In this way, the light of a larger wavelength within the C or L band applied to the input of the amplifier is amplified, thus widening the range of optical communication links. EDFAs typically operate in saturation and the average signal power determines the average gain. The dynamics of EDFA are unaffected by the sequence and dynamics of a digital signal or channel interaction in DWDM systems. As a result, multiple channels can be bundled within the total erbium spectral amplification bandwidth. However, the total average output power in both cases is determined by the saturation power of the specific EDFA.
-
Product
2- to 8-Channel Anti-Alias Low-Pass Filter and Instrumentation Amplifier Card
AAF-3
-
The AAF-3 is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier ISA bus plug-in board for front-end signal conditioning in PC-based data acquisition systems.
-
Product
MEGMET 1000 D
PU 187.21
-
Instrument PU 187.21 MEGMET 1000 D is intended for measurements of the insulation resistance up to 20 GΩ and the resistance of protective conductor up to 2 kΩ, its length; it can be used for checking the over-voltage protections. It also measures DC / AC voltage up to 1000 V and the temperature within the range -20 °C ÷ 120 °C, with a connected external sensor within the range -50 ÷ 850 °C. Nominal measuring voltages for the insulation resistance measurements are 50, 100, 250, 500, and 1000 V.
