-
Product
256 Channel Digital Input / Interrupt Output Module
DP-VXI-3099
-
DP-VXI-3099 is a high density module that provides 256 channels of digital input/interrupt and/or output for large scale digital input monitoring and control.
-
Product
Digital Input Board, 32 Isolated Channels, 24V
APCI-1032
-
32 digital inputs, 24 V or 5 V, incl. 16 interruptible inputs Optical isolation 1000 V Input filters Protection against pole reversal
-
Product
128 Channel Isolated Digital Input / Interrupt Module
DP-VXI-3117
-
DP VXI 3117 provides 128 isolated channel digital inputs for sensing DC levels and edge transitions of upto 48VDC. The input level selection for 5 (TTL / CMOS compatible), 12, 24 or 48V is made through on-board jumper selection. The debounce feature is programmable for a period of 2msec to 2147 sec. in binary increments. Channel groups 1 to 32, 33 to 64, 65 to 96 and 97 to 128 can each have a unique programmed debounce period, provided the ratio of clock period between groups does not exceed 32,768.
-
Product
Analog Input Module, 16-bit A/D
IP330A
-
The IP330A has many features to improve your overall system throughput rate. You can scan all channels or define a subset for more frequent sampling. Burst mode scans selected channels at the maximum conversion rate. Uniform mode performs conversions at user-defined intervals. Both modes can scan continuously, or execute a single cycle upon receiving a trigger.
-
Product
sbRIO-9207, Non-Enclosed, 500 S/s, 16-Channel C Series Voltage and Current Input Module
781069-01
-
Non-Enclosed, 500 S/s, 16-Channel C Series Voltage and Current Input Module - The sbRIO‑9207 is a combination voltage and current input module designed with industrial systems in mind. It features eight current and eight voltage input channels, with built-in noise rejection. Non-enclosed modules are designed for OEM applications.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
Low Thermal Input Cable
34102A
-
Use this 1.2-m shielded, 4-conductor connector only with the 34420A Micro Ohm Meter; terminated in copper spade lugs.
-
Product
Sixteen Channel, 12-Bit Analog Input Card
PCI-AI12-16(A)
-
Model PCI-AI12-16 is a multifunction, high-speed, analog-to-digital converter board for use in PCI-Bus computers. It accepts up to 16 single-ended or eight differential inputs. The board uses a low-noise, multilayer printed circuit board. Inputs are protected against overvoltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts.
-
Product
224 TTL Channels, Digital I/O With 4 Counters PXI Card
GX5732
-
The GX5732 is a 6U PXI static digital I/O card with 224 TTL I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5732 offers the highest digital channel density in the industry for a single PXI plug-in board.
-
Product
NI-9216, 8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module
785186-01
-
8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module - The NI‑9216 is a resistance temperature detector (RTD) input module. You can configure the NI‑9216 for two sample rate modes: high sample rate or high resolution. The NI‑9216 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3-‑or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per channel current excitation. The NI‑9216 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Geiger Counter
USB-RAD121
-
The USB-RAD121 is a radiation detector that runs completely off your computer's USB port. The device features a classic geiger counter click and light pulse for every count registered, while radiation levels are displayed on the computer. The simple RadGraph software interface displays and graphs readings over time, and even allows the readings to be streamed to a personal webpage.
-
Product
1MS/s, 16-Bit, 32-Ch Analog Input PCIE Card
PCIE-1805
-
32-ch single-ended or 16-ch differential or a combination of analog input16-bit A/D converter, with up to 1MHz sampling rateMulti-card synchronizationCurrent measurement (0-20mA or 4-20mA)Support digital and analog triggersAuto calibration
-
Product
Process Counters
TCT201-2ABC
-
The Process Counter TCT201-2ABC is a 1/16 Din 48 x 48 mm panel mount programmerable digital Counter with two 8 Amp relay outputs and up to 3 inputs. The TCT201-2ABC also has a potentiometer input that can accept either 5K or 10K Potentiometers. Other inputs can be PNP or NPN switches, 2 or 3 wire Proximity switches.
-
Product
Digital Input Board, 16 Isolated Channels, 24V
APCI-1016
-
*16 digital inputs, 24 V Optical isolation 1000 V Input filter*Protection against pole reversal*Standard drivers for:*Real time drivers for Windows 2000/NT/98.*The board is supplied with the universal software ADDIPACK.
-
Product
Digital Tap Position Indicator With Voltage &Counter Display
-
NMC''s latest offering digital tap position indicator with voltage and counter display, type: TX-204, is a fully micro controller based instrument used to indicate the tap position of the power transformer also indicating the voltage and counter indications simultaneously at a same time.
-
Product
48 Optocoupled Digital Inputs
YAV90321
-
Input Voltage 3…42Vdc Isolated Inputs / Control >1000Vdc CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
Product
PCI Card with input channels
PCI LVDS 8R
-
The PCI_LVDS_8R has 8 channels of LVDS input. The channels are grouped two per Filter Xilinx. The input data is filtered, then written to the Input FIFO. There is one Input FIFO per LVDS channel. 1K x 32. One Latch Xilinx handles 4 LVDS channels. The data is read from the Input FIFO by the Latch Xilinx and either written to the SDRAM or the Output FIFO.
-
Product
Reversible Counter
RV-3150
-
The RV-3150 reversible counter is newly released and so helpful to measure linear displacement, angular displacement and angle dimensions in the combination with Ono RP-series rotary encoder, roller encoder, and the like, which produce two-phase 90°phase difference output signals.
-
Product
PC/104 Digital Quadrature Encoder Input Board
104-QUAD-8
-
The 104-QUAD-8 card is a general purpose Quadrature Encoder Counter/Interface board. It is provided in the popular 104 format and conditions and monitors the outputs of 8 encoders. I/O connectors are right-angle 34-pin headers.
-
Product
Low-Cost 16-Bit Multi-Function DAQ Card with 2-CH Encoder Input
PCI-9221
-
The ADLINK PCI-9221 is a 16-bit high-resolution and low-cost multi-function DAQ card, with 16-CH singleended or 8-CH differential input capable of up to 250 kS/s sampling rate. In addition, the PCI-9221 comes with a 2-CH 16-bit static analog output and programmable function I/O. The software-programmable function I/O supports a variety of applications, including TTL digital I/O, general-purpose timer/counter, encoder input, and PWM output. The flexible function I/O makes the PCI-9221 the best single-board solution for combined data acquisition and simple motion control functionalities. Ideal for manufacturing, laboratory research, and factory automation, the PCI-9221 comes with all the functions you need at an affordable price.
-
Product
8-Ch Digital Input Module
ADAM-3651
-
Rated Input : >5mA @ 12 VDCCurrent : >10mA @ 24 VDCInput Filter : Programmable, Default 3msPulse Input Frequency : 150HzOver Voltage Protection : +40 VDC-40 ~ 70°C operating temperatureSupports Sink (Wet Contact) / Counter input type
-
Product
Programmable Multifunction Counter Board, Isolated, w/ 4 Function Modules & BISS-Master Logic
CPCI-1710-10K20
-
The board CPCI-1710 is a fast multifunction and multichannel counter board for the CompactPCI bus. The strengths of this board are its wide range of applications and high precision and reliability for though industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provides the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied sofware. The flexible programming facilities on this board allow many different user applications to be quickly and easily developed or reconfigured as further requirements arise.
-
Product
Isolated Input Relay Card With COS
PCIe-IIRO-16
-
This product is a x1 lane PCIe isolated digital input and relay output board with Change of State (COS) detection capabilities.
-
Product
Particle Counter
ST-9880
-
Standard Instruments Co., LTD.
This particle counter comes with a 2.8” TFT color LCD display for a gratifying visual effect. The camera function allows capturing JPEG images and 3GP videos conveniently. This versatile particle counter is widely used. 2.8'' color TFT LCD display. With a micro SD memory card to view images and videos on your PC. Gas (HCHO, CO) detector. Air temperature and relative humidity measurement.
-
Product
PCI Card with input channels
PCI_LVDS_8R
-
The PCI_LVDS_8R has 8 channels of LVDS input. The channels are grouped two per Filter Xilinx. The input data is filtered, then written to the Input FIFO. There is one Input FIFO per LVDS channel. 1K x 32. One Latch Xilinx handles 4 LVDS channels. The data is read from the Input FIFO by the Latch Xilinx and either written to the SDRAM or the Output FIFO.
-
Product
Digital Input Board, 32 Isolated Channels, 5V
APCI-1032-5
-
32 digital inputs, 5 V, incl. 16 interruptible inputs Optical isolation 1000 V Input filters Protection against pole reversal
-
Product
Analog Input Products
-
Analog input boards are useful for measuring variably changing conditions in the real world. When we want to measure these variably changing conditions, we need analog inputs to convert these changing real world conditions to changing electrical quantities. For example, monitoring the temperature inside a wood kiln, or the water pressure on the output of a pump, or the heart rate of a medical patient. In each of these cases, you can use one of our analog input devices to convert the electrical data from a sensor or transducer into binary data that can then be used by your computer.
-
Product
4 Channels, 2-28 Vrms Input, 5 kHz-10 kHz
LD3
-
A linear variable differential transformer (LVDT) is a type of electrical transformer/transducer used for measuring linear displacement (position). A counterpart to this device used for measuring rotary displacement is called a rotary variable differential transformer (RVDT). The RVDT is like an LVDT in that it measures a positional displacement, however, the displacement, which is still a linear proportional function, is based on rotary instead of linear positional movement.
-
Product
Programmable Multifunction Counter Board, Isolated, With 4 Function Modules
CPCI-1710
-
The board CPCI-1710 is a fast multifunction and multichannel counter board for the CompactPCI bus. The strengths of this board are its wide range of applications and high precision and reliability for though industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provides the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied sofware. The flexible programming facilities on this board allow many different user applications to be quickly and easily developed or reconfigured as further requirements arise.
-
Product
16-Channel VME RTD/Resistance Input Module
V410
-
The V410 is a 6U VME module that provides sixteen independent analog inputs that may be used to read RTDs, thermistors, and other similar resistive sensors. It can also read cryogenic diodes. Users may set input range and adjust other settings at VMEbus speed, and depending on the range selected the microprocessor will do the necessary calculations and output voltage, resistance, or temperature. Temperature conversion is available for 100Ω and 1000Ω, series 385 and 392, platinum RTDs.
