-
Product
Battery Condition Analyzer
BT-301
-
Kongter Test & Measurement Co., Limited
The BT-301 Battery Condition Anlayzer is updated battery handheld tester which is very effective and economical battery management device for testing battery internal resistance (or conductance) and voltage. It helps you eliminate weak batteries to ensure performance of your battery systems.
-
Product
48V / 300 Amp Load
BD18-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
EV Battery Test System
-
Shenzhen Sinexcel RE Equipment CO., Ltd
5V cell equipment adopts Sinexcel innovative circuit design + high-speed DSP complex algorithm, the detection process supports multi-gear switching; The equipment integrates voltage, temperature, pressure and other auxiliary channels, 20ms high-speed working condition simulation and other practical innovative functions to meet all aspects of battery electrical performance testing.
-
Product
Industrial Weighing - Wireless Load Cells
-
A wireless industrial weighing scale system can be advantageous, for instance when running conduit for cable is impossible, or if the cable could be damaged easily. In some cases the wireless interface is more economical than long runs of cable. These systems can be battery operated or hard wired to a power source if available. View our wireless load cell options below.
-
Product
AC Load Bank
-
PC software controls offer advanced load profile solutions and model options range from small, portable, low-power units, to high-power indoor or outdoor permanent load solutions.
-
Product
Battery Internal Resistance Tester
FST-7000
-
Foresight Electronics Co., Ltd.
Battery Conductance Tester is a portable digital measurement device for testing lead acid stationary batteries health and aging condition precisely within seconds. With the help of this device either single cells / blocks or large, multi group battery banks can be measured within a short time and the precisely measured data are processed and reported by given analyzer software automatically.
-
Product
Load Cells
-
Instron is the only testing system manufacturer that designs and builds its own load cells, ensuring exceptional accuracy, stiffness, and alignment across a wide measurement range. Produced at Instron’s High Wycombe, UK facility, each load cell is temperature-compensated and calibrated to international standards for outstanding repeatability. Backed by the largest commercial deadweight stack in the U.S., Instron’s calibration process delivers precision that often exceeds industry requirements—providing reliable, traceable performance for even the most demanding materials testing applications.
-
Product
Automatic Capacitor Batteries
-
Lifasa - International Capacitors, SA
The batteries of capacitors for automatic AT are designed for those applications in which the power levels in the AT network are variable. This type of equipment, with a number of steps normally between 2 and 4 to avoid phenomena in the installation resulting from the connection and disconnection of the capacitors in the electrical network, is controlled by a type MCX regulator, which tunes and regulates the input of the steps according to load levels, taking into account the expected waiting times of AT that between consecutive connections is 600 s., this time we can reduce it to less than 10 s. if we install TP for fast download.
-
Product
16CH Battery Cell Simulator
Chroma 87001
-
Chroma Systems Solutions, Inc.
Chroma 87001 Battery Cell Simulator is a high precision, programmable, and bidirectional DC power source with both voltage source and current source functions. In addition, the model can be used as a multi-channel DC power supply or an electronic load as well. A single simulator has 16 channels and each of them can set voltage and current respectively via Chroma software.
-
Product
48V / 250 Amp Load
BD15-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and is extremely cost effective.
-
Product
Terminations & Loads
-
We have more than 40,000 rf & microwave coaxial terminations in stock we can ship today. We offer these Microwave & RF terminations: SMA Terminations, Type N terminations, 7/16 DIN terminations, 2.92mm terminations, 2.4mm terminations, TNC terminations, smp terminations, minismp terminations, 4.1/9.5 minidin terminations. 4.3/10 terminations, ssma terminations, ssmc terminations, and a few Reverse Polarity terminations. Power levels of 0.5-150 watts. RF / Microwave terminations are also known as dummy loads or 50 ohm dummy loads. Our 1.85mm terminations, are rated to 67ghz. We offer 1.0mm terminations good to 110Ghz.
-
Product
Dynamic Mechanic Loading Tester
-
King Design Industrial Co., Ltd.
*Complies with IEC 61646, IEC 61215 mechanical load test specification. * Air pressure is adjustable, output range is from 2400pa to 5400pa ±5% . * Maximum measurement range: 220 x 260 cm. * Apparatus structure material：aluminum-extruded. * Fixtures and holders can be customized design for requirement of testing module. * Manual operation is simple; manual maintenance is easy.
-
Product
Advanced Battery Tester
DBT-12+
-
The tester enables safe measurement of voltage, current rating, state of charge and state of health for 12V and 6V batteries. The device is powered by an internal battery, so it can test even discharged batteries and can be conveniently used as a voltmeter.
-
Product
Battery Cell Insulation Tester
Chroma 11210
-
Chroma Systems Solutions, Inc.
Chroma 11210 battery cell insulation tester is an instrument used for accurately measuring leakage current (LC) and insulation resistance(IR) of battery jelly-roll/dry-cell as well as other insulation materials. In addition to standard LC/IR measurement, the 11210 has a unique function that detects partial discharge (PD) or flashover that may have occurred inside the insulation material during the high voltage insulation testing process.
-
Product
PXI 4 Banks of 40 Channel 1 Pole MUX
40-615-022-4/40/1
-
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
PXI 1 Bank of 160 Channel 1 Pole MUX
40-615-022-1/160/1
-
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
Battery Tester 12V Language
BT12L
-
The Battery Tester 12V Language (BT12L) is an inexpensive, simple and easy tool for testing automotive batteries. It has LED display that consumes very little current and will not drain the battery with repeated testing.
-
Product
Load Cells
-
Flintec load cells are highly accurate and built to last. We pride ourselves on the quality of our products and the service we provide.Our sensors are available globally. If your application requires a Custom Solution, our expert engineers can help.
-
Product
DC Electronic Load
EE30180A
-
The EE30180A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running.
-
Product
Unclamped Inductive Load Tester
ITC75100
-
The ITC75100 is an enhanced unclamped inductive load (UIL) test system that builds on the success of ITC’s industry leading ITC55 series of testers by adding additional test and measurement capability.
-
Product
48V / 200 Amp Load
BD12-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
Load Measuring Pins
-
Magtrol Load Measuring Pins are temperature-compensated transducers used to measure load and force and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load.
-
Product
Battery Cell Surge Tester
19311
-
The Chroma 19311 series battery cell surge tester is designed for testing the insulation quality between the positive and negative plates of the lead-acid battery cell. This is done by applying a high voltage surge/impulse before the electrolyte injection. Its output voltage can reach up to 6kV. It also has four terminal measurement and 200MHz sampling rate. The Chroma 19311 series has single channel (19311) and multi-channel (19311-10) tester.
-
Product
Single Point Aluminium Load Cell
EST-6
-
Technopark Automation & Control
The EST-6 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 600 x 500 mm. This load cell is available in capacities 500 kg and 1000 kg.
-
Product
Regenerative DC Electronic Load
IT8300 Series
-
ITECH newly launched IT8300 Regenerative DC Electronic Load, it not only can simulate various load characteristics, but also can feed power back to grid without pollution. IT8300 series unique regenerative function can convert the absorbed DC power into AC power and feed it back to local grid.
-
Product
Electronic Loads
-
Flexible electronic DC loads for general purpose applications. Voltage up to 80V, current up to 80A and power up to 600 watts. CI, CR, CG, CV and CP modes, built-in transient generators. Models with USB, RS232, GPIB and LXI compliant LAN interfaces.
-
Product
Electronic Loads
SLM AC/DC
-
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
-
Product
Load Cells and Sensors
-
AMETEK Sensors, Test & Calibration
Our high quality load cells and sensors are used for materials testing and force measurement all over the world.The full bridge load cells and sensors provide high precision measurements that ensure adherence to the international standards.
-
Product
Electronic Loads
-
Electronic loads are indispensable tools in several fields of electrochemistry, for example in the research of batteries and fuel cells. Using an additional external power supply you easily can extend an EL to a two-quadrant potentiostat you need e.g. in the field of electrolysis.
-
Product
Load Button Load Cells
-
Interface’s load button load cells are designed for customers who require the measurement of compression forces in a very low height space. They are designed to provide the most accuracy in as little space as possible. The smaller ConvexBT or LBMU can fulfill the need for force measurements at a very respectable precision level that is enough for most applications. Diameters range from ⅜ of an inch to just over 3 inches, with heights from ⅛ of an inch to 2 inches. The shaped load button has a spherical radius to help confine misaligned loads to the primary axis of the cell.
