Rate Sensors
Measures rotational velocity around a sensitive axis.
-
Product
10 MHz To 67 GHz LAN Thermal Vacuum Compliance Power Sensor
L2067XT
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
3U OpenVPX Sensor Interface Unit
SIU32S
Sensor Interface Unit
The SIU32S is a highly configurable Modular Open Systems Approach (MOSA) rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, processing, communications and Ethernet switching. The SIU32S leverages NAI’s Configurable Open Systems Architecture™ (COSA®) 3U boards and smart function modules to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
Thermocouple Power Sensors
N8485A
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
Differential Sensor, Wide Dynamic Range, 100 MHz
CX1105A
Power Sensor
The CX1105A ultra-low noise differential sensor is a dedicated accessory for the CX3300 series and enables dynamic current measurements from 1 μA to 100 A under up to 100 MHz bandwidth with existing shunt resistors on your test board.
-
Product
120 GBd High-performance BERT
M8050A
Bit Error Rate Tester (BERT)
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
Product
Waveguide Power Sensor
R8486D
Power Sensor
Excellent SWR for reducing mismatch uncertainty50 MHz calibration port Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 26.5 GHz to 40 GHz Diode power sensing element
-
Product
Frequency Selective Power Sensor
NRQ6
Power Sensor
The R&S®NRQ6 is based on receiver technology and can perform band-limited power measurements down to -130 dBm. The R&S®NRQ6 combines high-precision with high-speed measurements beyond the limits of currently available power meters. In addition to conventional continuous average measurements, the R&S®NRQ6 has a trace display function and also performs ACLR measurements.
-
Product
10 MHz to 33 GHz USB Wide Dynamic Range Average & Peak Power Sensor
U2063XA
Power Sensor
The Keysight U2063XA is a fast, accurate and wide dynamic range 10 MHz – 33 GHz USB peak power sensor.
-
Product
E-Series Average Power Sensor
E9300A
Power Sensor
The E9300A diode power sensor measures average power over the frequency range 10 MHz to 18 GHz and power range -60 to +20 dBm (80 dB dynamic range).
-
Product
E-Series Peak and Average Power Sensor, 50 MHz to 6 GHz
E9322A
Power Sensor
The E9322A power sensor has a 1.5 MHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on TDMA and CDMA wireless formats such as Bluetooth.
-
Product
P-Series Wideband Power Sensor, 50 MHz to 40 GHz
N1922A
Power Sensor
Peak, peak-to-average ratio, average power, rise time, fall time, maximum power, minimum power, and statistical data of wideband signals.
-
Product
S2 Penta Sensors
ULP-S2 PCI/V
LED Sensor
Optomistic Products’ best-selling Sensor, the ULP S2 Penta Sensor, is relied upon for its versatility in accommodating most LED color and intensity test applications. Implemented in a unique and customizable 2-Part solution, the S2 Penta Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption:Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsOutput Loads: ‘Int.’& ‘Color’- 2Kohms min., 100pF max.Output Pins: 4 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longTypical response times: Typical response time: <10mS capture time; <100mS overall responsetime for color and intensity simultaneouslyFiber-Optic Probes: Can be paired with any Universal LightProbe Fiber-Optic Probe
-
Product
E-Series Peak and Average Power Sensor, 50 MHz to 6 GHz
E9321A
Power Sensor
The E9321A power sensor has a 300 kHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on TDMA wireless formats such as NADC, GSM and EDGE.
-
Product
Waveguide Power Sensor
V8486A
Power Sensor
The V8486A waveguide power sensor measures average power over the frequency range 50 GHz to 75 GHz and power range -30 to +20 dBm.
-
Product
Thermocouple Power Sensors
N8487A
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
Dual Channel, ±12 V, 100 MHz, 40 NA – 1 A
CX1102A
Power Sensor
The CX1102A dual channel current sensor is a dedicated accessory for the CX3300 series mainframe and features wide dynamic measurement ranges due to the simultaneous capture technology.
-
Product
Balance Thermocouple Power Sensor, DC To 50 GHz
N8487S
Power Sensor
The Keysight N8480S Series Balance Thermocouple Power Sensors are intended to be used as measurement standards for RF power. They are suitable for use in a microcalorimeter-based primary measurement standard and as a secondary or reference measurement standard. The new balance thermocouple power sensors offer a broad frequency range DC up to 18/50 GHz, high maximum input power of +20dBm, fast measurement speed/settling time as well as ease of maintenance.
-
Product
Diode Power Sensor
8487D
Power Sensor
Excellent SWR for reducing mismatch uncertainty Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 50 MHz to 50 GHzDiode power sensing element
-
Product
10 MHz to 18 GHz USB Wide Dynamic Range Average Power Sensor
U2052XA
Power Sensor
The Keysight U2052XA is a fast, accurate and wide dynamic range 10 MHz – 18 GHz USB average power sensor.
-
Product
POF Ext Ø 1,5mm 600mm, from 5mm Lens to VPC ITA Contact
YAV90CLR10
LED Sensor
The probes for sensing LEDs, P/N YAV90CR10 feature an Optical Head to correct missalignment errors in X and Y axis. As a result, the relative read out will oscillate less tan 5% with a missaligment of + 0,5 mm Offset
-
Product
Thermocouple Power Sensors
N8482H
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
10 MHz To 50/53 GHz LAN Wide Dynamic Range Average Power Sensor
L2055XA
Power Sensor
The Keysight L2055XA is a fast, accurate and wide dynamic range 10 MHz – 50/53 GHz LAN average power sensor.
-
Product
10 MHz To 54 GHz USB Wide Dynamic Range Average Power Sensor
U2056XA
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis
-
Product
Single Channel, ±40 V, 100 MHz, 40 NA – 1 A
CX1101A
Power Sensor
The CX1101A single channel current sensor is a dedicated accessory for the CX3300 series mainframe and features wide common mode voltage range. The maximum current can be expanded to 10 A using a CX1206A.
-
Product
Universal LightProbe S2 Sensors
LED Sensor
Optomistic Products’ Universal LightProbe S2 Sensors are designed for the In-circuit, Functional or Finished Product test of an LED’s color and/or intensity. Implemented in a unique and customizable 2-Part solution, the S2 Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.
-
Product
Power Sensor and SNS Noise Source Cable (6.1m/20 feet)
11730C
Power Sensor
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
Product
Peak And Average Power Sensor, 50 MHz - 6 GHz, 5MHz Bandwidth
E9323A
Power Sensor
The E9323A power sensor has a 5 MHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on W-CDMA wireless formats such as cdma2000.
-
Product
10 MHz to 6 GHz USB Wide Dynamic Range Average & Peak Power Sensor
U2061XA
Power Sensor
The Keysight U2061XA is a fast, accurate and wide dynamic range 10 MHz – 6 GHz USB peak power sensor.
-
Product
Wide Dynamic Range Power Sensor, E-Series
E4412A
Power Sensor
Fast measurement speed, up to 400 readings per second with the E4416AWide dynamic range (-70 dBm to +20 dBm)Calibration factors, linearity ana temperature compensations data stored in EEPROM Excellent SWR for reducing mismatch uncertainty Accurate calibration and traceability to NIST Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
50 MHz to 18 GHz USB Peak and Average Power Sensor
U2021XA
Power Sensor
The U2020 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming.
