Roughness Testers
See Also: Roughness
-
-
-
Product
ADSL Testers
-
The common used ADSL Tester is ADSL2+ Tester. It is an easy-to-use, hand-held advanced telecommunication tester that used for the installation, maintenance and measurement of ADSL2+ service. This tester supports the testing function such as parameter, error, DMM, PING that related to ADSL2+ service, user register authentication on the ADSL2+ user’s line side. It also directly enables the engineers to verify, troubleshoot and evaluate the ADSL2+ service. It is the right tool for the network test job.
-
Product
Snap Tester (Button Pull Tester)
TF145
-
TESTEX Testing Equipment Systems Ltd.
Snap Tester (Button Pull Tester), to determine the holding or breaking strength of prong-ring attached snap fasteners onto garments or toys, also as a Push Pull Tester for compression and tensile testing of small samples(special attachments are available).
-
Product
Earth Tester
TAURUS PRECIOHM ET
-
The TAURUS PRECIOHM ET is one of the specially designed products by TAURUS to measure earth resistivity and earth resistance in a power station. These tests are performed based on 4 point (Wenner) and 3 point (fall of potential) methods respectively. All electrical equipment in the substation and power stations are electrically connected to station earth mat with earth electrodes. The earth electrode ensures that in the event over voltage on the system due to system fault or lighting discharges etc., the parts of the equipment which are normally ”dead” as far as voltages are concerned; do not attain dangerously high potentials. An earth electrode will only be effective so long it has a low resistance to the earth and can carry large currents without deteriorating. Thus the resistance of earth electrode should be low to give good protection and it must be continuously measured and monitored in all the substations and power stations.
-
Product
Optomechatronics Testers
-
T100 is a flying actuator tester designed to calibrate and test any kind of device, module or product with electronic, optical and mechanical functions, using the latest opto, MEMS, sensor, microelectronics, micromechanics technologies.T100 can be equipped with tools and actuators to perform calibration, electrical test, mechanical test, optical test.All on a single machine without any need for additional equipment.It is the ideal tester for production lines with a wide variety of products and frequent entry of new ones.
-
Product
Microhardness Testers
-
Newage Testing Instruments, Inc.
Newage Testing Instruments offers a range of microhardness testing solutions including the cost-effective MT91 and MS-ZH microhardness testing system.
-
Product
Hi-Pot Tester
DU3315A/3316A
-
Delta United Instrument Co., Ltd.
Real-time Open Check of the alarm and signal output of no contact signal3 in 1 tester with AC, DC, IR functions ( IR function is optional for DU3316 only)ARC Detction:DU3315A /DU3316A Standard function40 x 4 LCD text displayFast cut-off time : 0.4ms5 sets of memory, 3 steps for each memory
-
Product
Adhesion Tester
-
ilm adhesion testing of thin films and stacks on substrates for material evaluation.
-
Product
Resistance Tester
KT-2000RD
-
This equipment represents the wanted resistance value in digital figures and at the same time, is an ohmmeter which decides products to be bad in case of being out of the previously set range of H,L and to be good in case of being within the range. Moreover, because it is designed and manufactured on the basis of KAST's business experiences and know-hows accumulated through on-the-spot works for a long time, it is highly trustable, especially strong to noise and impulse that occur on the bad electric condition of on-the-spot or on the connection with any other equipments, and also is convenient for use.
-
Product
Decoder Tester
-
Electronic Solutions ULM GmbH & Co. KG
Decoder tester for decoders, plug in for NEM652, NEM651, 21MTC, single wire, motor, LED monitor and 20mm speaker. It´s so easy to handle and knows all kind of interfaces.
-
Product
Abrasion Tester
rHT SeriesHB SeriesHT Series
-
Abrasion tester checks the abrasion of solid materials. such as metals, composites, ceramics and more.The test is performed on worn materials such as tires, shoes, belt and more.* Worn out condition* The loss of the weight* The loss of the physical volume* The thickness that been worn out, etc* Use NBS standard gum to ratio the endurance characteristic of abrasion for this material.
-
Product
Cable Tester
CT100
-
The intelligent, CPU-controlled CT100 accepts virtually any connector type: XLR, mono and TRS phone ( 1 /4 ", 1 /8 ", TT), RCA and MIDI. It shows which input pin is connected to which output pin. Separate LED's indicate proper shield connection and phantom power presence. The CT100 also offers an installed cable test mode and a continuity check plus a test tone generator.
-
Product
Color Tester
OCM-510 series
-
The OCM-510 Color Tester has an internal Czerny-Turner spectro- scope and along with providing both high-wavelength precision and high-wavelength resolution in a compact unit also employs a high-precision yet high-sensitivity line sensor in the detector to serve as a versatile spectrophotometric device for making optimal high-speed measurements.
-
Product
Single-functional testers
3110
-
The MI 3110 EurotestIM is a perfect tool for testing of permanent integrated or portable Low Voltage Electrical Installa-tions supplied by Generator or Transformer and protected by an IT earthing system. Designed for simple but efficient safety testing of Integrated IT Earthing System powered with LV Generator or Transformer! With a single, pre-programmed AUTO SEQUENCE® with sub-tests and adjustable limits it is possible to perform all the necessary verifications of safety limits of a specific LV IT installation.
-
Product
TIM Tester
-
The Analysis Tech TIM Tester 1300 is an automated test system for measurement of thermal impedance and conductivity on thin, thermally conductive materials of the type frequently used for electronic packaging, as well as a wide variety of flexible or rigid solids and semi-liquid or viscous materials. Generally, the TIM Tester 1300 can accommodate samples with high-to-medium thermal conductivity with contact pressures ranging from 10 to 550 psi (70-3800 kpa) and at sample temperature ranging from 15C to 70C.
-
-
-
Product
Oscilloscope Tester
ScopeTester 5
-
ScopeTester 5 is 5-channel oscilloscope tester for PCs. Unlike traditional oscilloscopes it is capable of continuous acquisition of signals without dead times. This feature gives exceptional diagnostic value. Available voltage ranges matches typical signals found in modern cars. The user may connect to vehicle sensors, actuators and other diagnostic equipment, such as current clamps, inductive and capacitive probes and other diagnostic probes.
-
Product
Unbalance Tester
BK2027
-
If you need to test displacement in hard drive motors with speeds up to 10,000rpm, think about BaKo's Type BK2027 Unbalance Tester. It's both easy to set up and easy to use and as a 2 channel DSP based system, it can test 2 motors at once and display the balance results as either unbalance (cm.g), acceleration (m/s2) or vibration strength (g).
-
Product
Qualification Tester
CableIQ
-
CableIQ qualification tester is the first cabling bandwidth tester for network technicians. This Ethernet network cable testergives even the most novice tech the vision to see what speeds existing cabling can support, quickly isolate cabling from network problems, and discover what is at the far end of any cable.
-
Product
Receptacle Tester
RT500
-
Designed to detect the most common wiring problems in standard 120V receptacles.Test for correct wiring, open ground, reverse polarity, open hot, open neutral, hot and ground reversed.Conditions NOT indicated: Quality of ground, multiple hot wires, combinations of defects, reversal of grounded and grounding conductors.Large light indicators for greater visibility.Reinforced prongs for increased durability.Push-pull design with slip-resistance ribbing.Made in USA of U.S. and imported parts.
-
Product
IPTV Tester
NetProbe 2000 IPTV Analyzer
-
The NetProbe 2000 IPTV is a handheld IPTV tester that can emulate a set top box or passively monitor video channels in pass-thru mode. It can be used to turn up new service by auto scanning all channels and checking their quality or to troubleshoot the service. It is battery powered and easy to operate by a tier one technician.
-
Product
Insulation Tester
1555
-
The Fluke 1555 insulation resistance tester offers digital insulation testing up to 10 kV, making it ideal for testing high voltage equipment including switchgear, motors, generators and cables.
-
Product
OTDR Tester
M-OTDR-502
-
Fuzhou Metricu Technology Co Ltd
Optical Time Domain Reflectometer Wavelength 1310 / 1550nm, max test range 150KM, Dynamic range 28 / 26dB, SOR standard data saving, create PDF/EXCEL format report, stable laser source, support CW/270/330/1000/2000Hz, Test fiber's length, loss, attenuation parameters and event map, locate connection point/fusion point, Automatic analysis of various linkers/fusion points, easy analyze of various events,Support saving curves number ≥30000pcs, loss test, detect the optical or optical components loss value, etc. Test IP camera, optical power meter, visual fault locator, RJ45 cable TDR test, cable tester, cable tracer, etc.
-
-
Product
Packaging Compression Tester
KRD101 series
-
KRD101 Series Packaging Compression Tester is designed to evaluate the compressive strength of packaging in order to prevent the product from deforming or being damaged during handling, stacking, storage, and transportation due to insufficient packaging strength. This machine is one of the main testing equipment for corrugated packaging performance and comprehensive indicators, and is an ideal testing equipment for papermaking, packaging, commodity inspection, scientific research and other departments.
-
Product
Lightning Rod Tester
LR TESTER
-
Nimbus lightning rod tester for testing the early streamer emission internal circuit as well as the level of protection of the lightning rods.
-
Product
Cylinder Leakage Tester
EEPV509
-
Input pressure gauge displays input air pressure for proper cylinder leakage test set up and accurate results Pressure gauge range is 0-100 psi (0-700 kPa) in 2 psi (20 kPa) increments. Cylinder leakage gauge displays leakage as a percentage of input pressure with 3 distinctive zones of high, moderate and low
-
Product
Torque Tester
WDI series
-
New standard torque tester. Manage electric screwdrivers, manual torque screwdrivers, and wrenches with this one unit! WDI-10HR WDI-100HR WDI-250. THE CULMINATION OF 50 Years of Manufacturing TORQUE MEASURING TOOLS.
