Sensors
detect a physical event then translate to a representative analog signal.
See Also: Measurement, Detectors, Meters, Transducers
-
product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781209-01
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge ...show more -
product
Polarity Indicator Circuit Tester
CT8007
No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance electronic circuitry. Negligible current draw ( 1 microampere) is 30,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 6 and 28 Volt DC in battery powered systems
-
product
PXI BRIC8 FIBO Matrix Dual 80x4 3pin brkout
40-592A-104
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
Transverse HD Sawmill Meter
MC PRO 1500 HDNC
Finna Sensors built the Transverse HDNC Sawmill Meter to increase the number of potential sensors from 8 to 24. The sensors can now be specified to fit within chain runs and can be located on both the top and bottom faces. This significant increase in surface area allows mills to identify sapwood/heartwood boundary areas or wet pockets for proper sorting prior to kiln drying. Sorting by moisture content has been shown to improve drying productivity by 10% to 15%, as well as, enhance lumber recovery. Further advancements in the software allow users to track packages through the drying process, add Internet of Things (IOT) data and perform advanced analytics with new reports.
-
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-113
The 40-297A-113 (PXI) and the 42-297A-113 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 238 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-054
The 40-297A-054 (PXI) and the 42-297A-054 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 22.3 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Temperature Measurement IR Sensors & Detectors
ST150 With Diffractive Lens
A single-channel silicon-based thermopile with integrated diffractive lens and internal baffle that delivers a very low Temperature Coefficient of Responsivity of -0.04%/C with a high output voltage, 19.5 FOV and a quick time constant of 38ms. This Low-cost detector comes in a TO-5 package and has a very short thermal shock response to ambient temperature change.
-
product
PCI Precision Resistor Card 6-Channel, 2.5Ω To 102kΩ
50-297-040
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Pyranometer products
Hukseflux Thermal Sensors B.V.
Hukseflux is a leading manufacturer, both in technology and market share, of pyranometers, pyrheliometers, pyrgeometers, net radiometers and albedometers.We produce a complete range of solar and longwave radiation sensors, compliant with the latest ISO, IEC and WMO standards. Each Hukseflux pyranometer is classified as ISO 9060 secondary standard, first class, or second class, and offers the best measurement accuracy in its class. Pyranometer output is analogue and/or digital (Modbus over RS-485/TTL).
-
product
Oxygen Purity Sensors
At Process Sensing Technologies (PST) we specialize in offering replacement electrochemical oxygen sensors compatible with major fixed and portable oxygen analyzers, specifically tailored for enriched oxygen applications. PST’s oxygen purity sensors are designed to deliver unparalleled accuracy, ensuring optimal performance in diverse industrial settings.
-
product
Gauge Type T Thermocouple Wire
W-TW-24
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
product
Wireless Air Quality Sensors
AQW Series
Chuan Sheng Electronics Co., Ltd.
AQW series was designed for air quality measure, such as PM2.5, Ch20, CO2, temperature and humidity. Use high-precision sensor to ensure long-term stability and reliability of the instrument.Panel with large LCD display, easy to read the measuring value.And also have 4 LED indicator to indicate air quality status and device running.AQW series communication port is WiFi, it’s convenient for data collect, support Modbus TCP protocol, and others cloud protocol.
-
product
16-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-16
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
Ultrasonic Sensors
Accurately measure displacement of objects of any color -including transparent objects- with Omron's advanced ultrasonic sensors.
-
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-116
The 40-297A-116 (PXI) and the 42-297A-116 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 1.8 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI Resistor Module 2-Channel 2R to 32.7k with SPDT
40-293-132
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Camera BasedBeam Profilers
Our Camera beam diagnostic Line-up offers measuring capabilities starting from sub-micron laser beams to sensors of 1/1.2" with built-in automatic filters wheels. The camera based beam diagnostic offers the intensity measuring profile and the detailed beam power distribution within the profile.
-
product
Rotary Position Sensors -AEC- Q200 Compliant
A rotary position sensor translates angular mechanical position to an electrical signal. Rotary position sensors are designed for applications that typically require frequent adjustment. Shaftless designs allow for different engagement mechanisms, such as a customized shaft, a motor control, a human interface adjustment or a mechanical arm position locator. Rotary position sensors can be used in applications where a user needs to control a variable output such as a frequency, speed or volume con...show more -
product
Facility Fault Diagnosis System And Safety Management System
A system for diagnosing failures of rotating machinery such as turbines, motors, pumps, fans, and compressors, which are major facilities in nuclear power, hydropower, thermal power plants, petrochemical plants, shipbuilding, and aviation, through displacement sensors.
-
product
Single Channel Data Logger
Our range of Single Channel Data Logger are impeccable designed and take only single type of input. The one is a factory set and there are many sensors required. This an really work on the data stream including Modbus or a dedicated protocol but do not work on the applications where there is no sensor input.
-
product
Seismic Signal Conditioners
Seismic signal conditioners are designed to accept an input from (and provide power to) a seismic sensor. They convert the signal to a proportional 4-20mA DC signal that can be used as an input to process control instrumentation such as a PLC or DCS. They provide additional convenience features such as optional displays, BNC connectors for access to the dynamic sensor signal, and bandpass filtering. Metrix offers seismic signal conditioners that can accept either acceleration or velocity sensors, and are available with or without an integral display.
-
product
PCI High Density Potentiometer Card 2-Channel, 16-Bit, 0 To 65k Ohm
50-296A-021-2/16
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Thruline R.F. Sensors
Optional RFView output port on any WaveNode sensor (except SHF-series) allows the operator to sample coax R.F. on an oscilloscope. Connect a cable from the RFView port to your oscilloscope/spectrum analyzer for real-time RF monitoring. The output level is +13 dbm @ 1500 Watts , optimized for IMPure operation with SDR radios.
-
product
Carbon Dioxide Gas Measurements
LI-830 And LI-850
Some CO2 sensors are too simple. Other CO2 analyzers are costly and complex. But the LI-830 and LI-850 are just right – bringing proven performance at an economical price to provide CO2 gas measurements that you can depend on day after day.
-
product
Active Alignment Assembly & Test Platform
Quickly deliver flawless camera & LiDAR modules, MEMS devices, die based sensors, LED and laser-based headlights and other high-end products with a supremely accurate standardized platform.
-
product
IO-Link
The IO-Link® interface simplifies communication to smart sensors and actuators, combining signaling with power-over-cable technology. It has become one of the key devices as industrial automation systems are growing more interconnected and intelligent to accommodate demands for centralized control and optimized production. Analog Devices implements both device PHY and master PHY interfaces (COM1/COM2/COM3). Designing with harsh industrial environments in mind, the master 4-port IO-Link power and...show more -
product
Pocket Conductivity Testers
Labodam pocket conductivity testers are equipped with platinum sensors and 1 point brush calibration system. These easy to use pocket conductivity meters come with waterproof design features for protection against harsh conditions. The conductivity meters can be used for measuring the conductivity of drinking water, waste water, brine water, and liquids with high, low conductivity.
-
product
3D Sensor
C6 Series
The new 3D C6 series by AT is built on a novel sensor platform that supports the latest industrial standard GigE Vision/GenICam 3D at 1 Gbit/s. These new laser profilers offer an impressive combination of extremely fast and highly precise resolution, reaching up to 4,096 points per profile, a profile speed of up to 200 kHz, and high dynamic range 3D image capture. They are available as compact sensors, MCS, and 3D cameras.
-
product
IR Temperature Sensors for Critical Equipment Monitoring
FLIR A310
The FLIR A310 is a fixed-mounted thermal imaging camera that can be installed almost anywhere to monitor your critical equipment and other valuable assets. The camera can safeguard your plant and measure temperature differences to assess the criticality of a given situation. This allows you to see problems before they become costly failures, preventing downtime and enhancing worker safety.
-
product
Capacitance Simulation Card
SET-1220
The SET-1220 device is a designed capacitive fuel sensor emulation for NI-SLSC. This card provides eight isolated channels that can emulate capacitance values between 10pF and 800pF. It was designed to emulate capacitive sensors that are typically connected between an excitation voltage on one end and a virtual ground on the other end.