Filter Results By:

Products

Applications

Manufacturers

Sensors

detect a physical event then translate to a representative analog signal.

See Also: Measurement, Detectors, Meters, Transducers


Showing results: 2506 - 2520 of 3239 items found.

  • PCI Resistor Card 2-Channel 2 Ohm To 131k Ohm

    50-293-034 - Pickering Interfaces Ltd.

    The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.

  • PCI Resistor Card 2-Channel 1.5 Ohm To 4.09k Ohm

    50-293-023 - Pickering Interfaces Ltd.

    The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.

  • PCI Resistor Card 2-Channel 1.5 Ohm To 2.04k Ohm

    50-293-022 - Pickering Interfaces Ltd.

    The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.

  • Electronics

    BAE Systems Inc.

    We develop and deliver a wide range of advanced technologies for the commercial and military electronics markets. Our portfolio includes flight and engine controls, electronic warfare and night vision systems, surveillance and reconnaissance sensors, mobile networked-communications equipment, systems integration, and environmentally friendly energy management systems.

  • Digital Signal Processor

    CHAMP-XD2M - Curtiss-Wright Defense Solutions

    Imaging sensors, RADAR, and SIGINT provide an overwhelming amount of data that needs to be stored before it can even be processed, but current solutions offer far from enough memory to store it. By providing more memory capacity on a single board, systems can remain SWaP-C optimized and data can be connected and processed with ease.

  • Test Of Aviation Turbo Starter

    ViTec Co. Ltd

    The use of a 16-bit analog input board provided high measurement accuracy, and the use of the SCXI reconciliation system allowed the integration of signals from the most diverse sensors in one configuration. The software developed at LabVIEW implements all kinds of tests of turbo starters in full accordance with the approved methods.

  • Environmental Monitoring Systems

    Eurotech Inc

    Eurotech environmental monitoring systems are designed to provide a scalable, efficient and compact solution that integrates multiple sensors in a single, easy to deploy unit. These compact, easy to install environment monitor systems collect and analyze air quality parameters, electromagnetic fields, ionizing radiation levels and sound pollution.

  • Imaging Photometer & Colorimeter

    LumiTop 4000 / 2700 - Instrument Systems Optische Messtechnik GmbH

    The patented optical design permits simultaneous measurement of all three sensors in one shot. The accurate spectral measurement is used as a live reference and transferred to the complete display area of the camera. This makes for extremely short measurement times and all relevant optical tests are conducted in a single test station.

  • Scienlab Measurement And Control Module

    SL1068B - Keysight Technologies

    The Measurement & Control Module SL1068B is a rack-mount measurement module which provides voltage outputs for analog signaling – useful e.g. for the emulation of temperature sensors or the controlling of regulation vents with voltage input with 8 channels. The module can be used either as a stand-alone device or as extension for a Scienlab Battery Test System.

  • Flexible Rope-Type Current Probe

    RCT1A and RCT5A - Powertek LLC

    These probes have great bandwidth ensuring accurate measurement even with harmonically distorted wave shapes. For all RCT1A/RCT models, a NIST, NAVLAP, NPL (UKAS) factory traceable calibration certificate and certificate of conformance is supplied. UL/CSA approved materials are used throughout. Three phase and single phase flexible AC current sensors (rope sensors) are available for fast installation in confined spaces, eliminating the need for Electrical Supply Shutdown. Available outputs are 1A @ 2.5VA and 5A @ 0.5VA, this means long cable lengths from current sensor to signal conditioner allow these low VA ratings to be used, even when feeder cable to energy meter distances are large (up to 98 feet / 30 meters)

  • Embedded Vision

    MVTec Software GmbH

    In the industrial environment, especially in digitalized, automated production scenarios, more and more so-called embedded systems are being used. Embedded devices are small, with compact dimensions, highly efficient, and generate little waste heat. Therefore, they are also suitable for limited space conditions. Due to often harsh environmental conditions, they must be particularly robust and resistant to external influences like  massive dust accumulation, strong vibrations, and high humidity or even direct contact with water. Typically, embedded devices are handhelds, smartphones, tablets, vision sensors, smart cameras, smart sensors and single board computers. If the systems have integrated machine vision software, they can be used for a wide range of image processing applications. This is known as embedded vision.

  • sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module

    781028-01 - NI

    Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.

  • sbRIO-9234 , Non-Enclosed, 4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module

    782718-01 - NI

    Non-Enclosed, 4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module - The sbRIO‑9234 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The sbRIO‑9234 is also compatible with smart TEDS sensors. The sbRIO‑9234 delivers a wide dynamic range and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti‑aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking. Non-enclosed modules are designed for OEM applications.

  • FD-11634, 8-Channel Sound and Vibration Input Device for FieldDAQ

    786471-01 - NI

    The FD-11634 can measure signals from integrated electronic piezoelectric (IEPE) and non-IEPE sensors such as accelerometers, tachometers, and proximity probes. The device also works with smart TEDS sensors, delivers a wide … dynamic range, and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals and have built-in anti-aliasing filters that adjust to your sample rate. This device is IP65/IP67-rated to be dust-tight and water-submersible and can sustain 100 g shock and 10 g RMS vibration in -40°C to 85°C environments. You program the FD-11634 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. When used with NI software, this device can provide processing functionality for condition monitoring such as frequency analysis and order tracking.

  • sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module

    781209-01 - NI

    Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.

Get Help