Partial Discharge Detection
indicate that localized dielectric breakdown within insulation has occured.
See Also: Partial Discharge, Partial Discharge Monitors, PD, PD Test, Partial Discharge Test, Partial Discharge Detectors
-
Product
Repeated Charge Discharge Test Set
-
The IS 13341 : 1992 has laid down the requirements for Ageing Test, Self-Healing Test and Destruction Test on Shunt Capacitors of the self healing type for AC Power Systems. The Ageing Test is to be performed at a specified voltage of 1.25 times the rated voltage for 750 hours. The test is to be followed with a repeated discharge cycle test which involves charging of the capacitor to a DC voltage and discharge of the same through an Inductance. Sivananda Electronics has developed this equipment for the benefit of capacitor manufacturers, for the first time in India.
-
Product
Ultrasonic Leak Detection Camera
Leakshooter LKS 1000-V.2
-
1st ultrasonic compressed air, gaz and vacuum leak detector with camera. Specialy dedicated to visualize the spots where compressed air is leaking, the LEAKSHOOTER LKS 1000 – V.2 has many other applications such as : steam trap monitoring, bearing monitoring, electrical applications like partial discharge, corona effects, punctured isolators, electrical tracking detection.
-
Product
Intermittent Fault Detection & Isolation System
IFDIS
-
The IFDIS™ uses patented Intermittent Fault Detector technology that simultaneously and continuously monitors every circuit path within a Unit Under Test (UUT) - such as a Line Replaceable Unit (LRU) chassis' interconnects - for intermittent continuity failures that occur for as short as 50 nanoseconds. This state of the art technology is combined with an environmental chamber and vibration table, which simulate the UUT’s operational environment and cause intermittent faults to manifest, creating a system that is unsurpassed in intermittent fault detection.
-
Product
Near-Field Detection Module for Imaging
Transmission
-
Detection optimized for high performance near-field imaging in transmission-modeEnables optical amplitude and phase resolved near field measurementsPatented background-free detection technologyEnables bottom-side (transmission-mode) sample illumination with broadband mirrorSuited for visible and infrared wavelength range 0.5 20 mRequires transparent sample substrateMotorized parabolic mirror for easy beam-alignment in transmission-modeStationary focal point with respect to AFM-tipVariable illumination spot size (ca. 2m 100m)Suitable for plane-wave illuminationSupported AFM scan-speed: up to 20 m/s @ highest spatial resolution
-
Product
Non Contact Voltage Detection
-
Our range of Non Contact Voltage Detectors offer a safe and accurate method of checking for voltage present on a conductor. With audible and visual indication, our range offers total confidence when checking cables for live voltages
-
Product
Oxygen/Nitrogen/Hydrogen by Inert Gas Fusion Infrared and Thermal Conductivity Detection
836 Series
-
The ONH836 Oxygen/Nitrogen/Hydrogen Elemental Analyzer is designed for wide-range measurement of oxygen, nitrogen, and hydrogen content of inorganic materials, ferrous and nonferrous alloys, and refractory materials using the inert gas fusion technique.
-
Product
Water Detection Sensor
EZ-10
-
Panasonic Industrial Devices Sales Company of America
The EX-10 is a special Thru-Beam Sensor that was designed for two purposes; to check fluid levels and to detect the level of liquids containing water. The emitter on the EX-10 Sensor uses a particularly strong IR beam to not only penetrate transparent, but also semitransparent or colored containers such as PFA packages or shampoo bottles. Also, the sensitivity of the Sensor is adjustable to allow it to focus on a target, such as distinguishing foam from liquid in drinks, as an example.
-
Product
Analog Ultrasonic Detection System
ULTRAPROBE 2000
-
Designed for ease of use, it often takes no more than 15 minutes to become competent in testing with the ULTRAPROBE 2000 Kit Complete. Fast accurate diagnosis through the ULTRAPROBE 2000 System will dramatically reduce unplanned down time and shorten planned outage time.
-
Product
Smoke Detection Sensor - UL Approved, TAA Compliant
ENVIROMUX-SDS-TAA
-
For warning of smoke. Photoelectric smoke detector. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Voltage Supply: 8-35VDC. Current Consumption: 200uA. Alarm Output: Relay (NO). Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL. TAA compliant.
-
Product
ESD Discharge Simulator
Model 9910 PurePulse/PinScan
-
Model 9910 PurePulse / PinScan is used to determine the ESD susceptibility level of electronic devices up to ±4kV. PurePulse generates ESD pulses up to 4kV for testing electronic devices for susceptibility to Electrostatic Discharge (ESD) using HBM, MM and HMM models. PinScan provides automatic sequencing of ESD testing of up to 128 pin devices, applying a discharge, thenperforming a curve-trace test to identify a failure.
-
Product
Gas Detection System
TOC-625 MICRO
-
International Gas Detectors Ltd
For small systems up to 8 devices with simple I/O requirements this system is ideal. The TOC-625 Micro Gas Detection System Controller interfaces with existing TOC-30A addressable gas detectors and has auto detect and set up features making deployment fast and easy for installers not used to gas detection systems.
-
Product
Detection Electronics
-
Our detection electronics portfolio comprises all the detection electronics elements required for the operation and automation of a high quality light measurement system, including photo-detector signal recovery and digitisation (with fully programmable DC, AC and lock-in amplifiers having current/ voltage inputs), high voltage supply, optical chopper control, detector thermoelectric cooler control and relay unit.
-
Product
Detection of Earth Faults (PtG) and Short Circuit (PtP) Faults
CableTroll 2330
-
CableTroll 2330 is an indicator for detection of earth faults (PtG) and short circuit (PtP) faults on multi and single core cable terminations. The unit uses NorTroll type current sensors.
-
Product
Bomb Detection
-
Security Intelligence Technologies, Inc.
Bomb Detection with safety for the operator is the focus here at HSS Development. When searching with our bomb detectors, we understand the risks. We know a bomb can detonate at any moment, which is why a counter-measure is a necessary option.
-
Product
Wireless Wire Break Detection System
A909
-
The A909 is a wireless system that allows to detect wire breaks for cabling machines having no sliding contacts brushes.
-
Product
Subsea Pipe and Cable Detection & Tracking System
HydroPACT Dualtrack
-
Dualtrack is the combination of the 440 and the 350 systems to provide the ultimate subsea detection system, capable of tracking and surveying pipes and cables via ROV deployment.It utilizes the same industry standard pulse induction technology as the 440 system to survey accurately regardless of vehicle heading. The accompanying display and control software is Windowsâ„¢ based providing a familiarity factor that a specifically built interface would not.
-
Product
Cable Partial Discharge (PD) Spot Testing And Locating
PrecisePD
-
PrecisePD is an on-line PD Spot Testing and PD location system for Cables and Switchgear with advanced signal processing, used for the detection of PD in high noise environments.
-
Product
PCI Express Card With Eight Isolated Inputs, Eight Relay Outputs, And Change Of State Detection
PCIe-IIRO-8
-
This product is a x1 lane PCIe isolated digital input and relay output board with Change of State (COS) detection capabilities.
-
Product
Gunshot Detection & Localization System
-
Information System Technologies Inc.
ISTI’s acoustic transient (e.g. gunshot or any other) event detection and localization technologies exploit low-cost distributed sensors with local processing capabilities. Key benefits include: better capture of muzzle blast and ballistic shockwave in urban environments, lower false alarm, real-time response, robustness to loss of sensor nodes, low hardware complexity, flexibility to configure a dynamic local network and ease in deployment. The Graphical User Interface (GUI) allows for control over the sensors and network while providing an overall assessment picture. Unlike existing gunshot detection and gunshot localization systems, the distributed sensing solutions (algorithms and hardware/software) developed by ISTI can support different sensors including acoustic, seismic and IR.
-
Product
Lightning discharge counters
CDR-401
-
CDR-401 is the new counter which complies with the latest applicable Lightning Protection related Standards.
-
Product
Photo-Frame Style Smart Signal Detective Jammer
WF-DJ7
-
Shenzhen Tangreat Technology Co., LTD.
WF-DJ7 is a Painting Smart Signal Jammer.WF-DJ7 is designed mainly used for indoor cellphone signal detection and shielding, such as meeting rooms,border control units, Border Patrol and Drug Enforcement, Customs, Houses, Churches, Courts, Theaters, Offices,classrooms. checkpoint personnel, Hospitals, Recording Studios, Banks, Contract Tendering Rooms, Testing Facilities, Security Services, Military Units, Secret Services, News Conference Scene, Libraries, Museums,Prisons and so on.
-
Product
Fixed-Mount Thermal Imaging Camera for Condition Monitoring and Early Fire Detection
FLIR A500f/A700f Advanced Smart Sensor
-
FLIR A500f and A700f Advanced Smart Sensor Thermal Cameras are ideal for users who want built-in, on-camera analytics and alarm capabilities for outdoor condition monitoring and early fire detection applications. These cameras can help companies protect assets, improve safety, maximize uptime, and minimize maintenance costs. Featuring a protective housing designed to withstand harsh environmental conditions, FLIR A500f/A700f cameras combine unmatched thermal imaging with edge computing and industrial internet of things (IIoT) for simplified inclusion in new or existing networks. For VMS integrations, thermal and visible streams can be viewed independently or simultaneously. The cameras are easy to add, set up, and operate in HMI/SCADA systems, offering automation system solution providers a running start.
-
Product
Carbon and Sulfur in Inorganic Materials by the Combustion Infrared Detection Technique
844 Series
-
LECO combined our customers' feedback with innovative engineering to develop the CS844, an elemental analyzer designed for wide-range measurement of carbon and sulfur content of primary steels, ores, finished metals, ceramics, and other inorganic materials using the combustion technique. Our exclusive MS Windows®-based software, coupled with a boom-mounted touch interface, gives you complete access to instrument control, analysis settings, diagnostics, reporting, and more—without sacrificing valuable bench space.
-
Product
Real-Time Analysis, 160 MHz, Basic Detection, Multi-touch
N9030B-RT1
Signal Analyzer
See, capture, and understand elusive signals as short as 17.23 s with 100% POI and a complete set of advanced triggers View signal dynamics with integrated real-time displays Maximize your investment by adding RTSA at a fraction of the cost of a dedicated solution Easily integrate the 89600 software and thoroughly analyze complex signals Industry-leading 3 year warranty Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
IQ4 Pipeline Metal Detection
-
The IQ4 Pipeline is a robust system designed for both Sterile in Place (SIP) and easy strip down cleaning depending on the application, complying to EN1672-2 hygiene standards. This system is designed to be used with pumped and flowing products such as meat slurries, soups, sauces, jams or dairy.
-
Product
Particle Impact Noise Detection
BW-LPD-DAQ4000
-
Computer based controller with predefined MIL-STD test sequences stored (New)Create unlimited custom tests with multiple vibration frequencies and acceleration and other parameters to meet unique requirements (New)
-
Product
Vacuum & Leak Detection Software
-
Agilent vacuum and leak detection software and app provide the data management performance needed to meet manufacturing yields, quality-control standards, and compliance requirements in industrial vacuum applications.The powerful Vacuum Link app offers wireless remote pump control, making it easy to monitor your system.A-PLUS software enables the user to control and monitor vacuum solutions.Leak Test Data Wizard software enables powerful tracking and automation of leak detection processes.
-
Product
Corona Discharge Checker
MK-720
-
MK-720 enables finding of insulation deterioration on insulators, disconnectors, and circuit breakers, at hot-line condition!
-
Product
Seismic Detection System
-
For the purpose of increased reliability and unification, the seismic detection system is delivered as a standard kit placed inside of the compact leak-proof casing.
-
Product
Switched Limiting Amplifier With Detected Output
-
Limiting amplifier sets dynamic range from -10.0 to -5.0 dBm input to 2.0 dBm output. TTL controlled, fast switching and high isolation 10 dB On-to-Off, and includes internal filtering for improved harmonic performance. Analog detector monitored output, or dual RF outputs.
