Data Acquisition Systems
sense, log and store information. Also known as: DAS
See Also: Data Acquisition, PCI Data Acquisition, DAQ
-
product
Dual 16x8 1-Pole High-Density PXI Matrix Module
40-520-205
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
product
Power Supplies
Reliable power supplies enable data acquisition systems to continuously acquire and process data. Because our components use minimal power, many of our systems can be run using sealed rechargeable or alkaline batteries. Systems that require more power are often supplemented with external rechargeable batteries, regulators, ac transformers, or solar panels.
-
product
PXI 5 Banks of 16 Channel 2 Pole MUX
40-615-022-5/16/2
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration. Connections are made via a front panel 200-pin connector.
-
product
PXI High Density Mux 99 Channel 1 pole
40-670A-021-99/1
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
Multiple-Input Multiple-Output (MIMO) FRF Testing
EDM Modal MIMO FRF Testing includes a dedicated test setup and operation process flow using multiple simultaneous shakers to acquire FRF signals. Using a large channel count data acquisition system (i.e., Spider- 80X or Spider-80Xi), this shaker excitation method provides much higher efficiency and accuracy for the FRF measurements while minimizing local stresses on the test article.
-
product
Data Acquisition System - 3U 1-Slot
DAQ-31CP0G
The DAQ-31CP0G is a preconfigured rugged system with a high-performance, low power ARM® Cortex®-A9 processor. It is ideally suited to support a multitude of data acquisition applications that require high-density, multichannel, programmable communications consisting of: ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939) and Dual-Port Gig-E Ethernet.
-
product
PXI High Density Multiplexer, 20-Bank, 8-Channel, 1-Pole
40-615A-001
The 40-615A-001 is a 20-bank, 8-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
product
PXI Very High Density Multiplexer, 49-Channel, 4-pole
40-670C-022-49/4
The 40-670C-022-49/4 is a 49-channel, 4-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
PXI 2 Amp MUX, Dual 4-Channel 4-Pole
40-635-107
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
High Speed Links
HSL
ADLINK's Intelligent Remote Data Acquisition & Control Modules (NuDAM) are designed for data acquisition systems based on PCs and other processor based equipment with standard serial I/O ports (RS-232 or RS-485 with auto direction control).
-
product
PXI MUX 8 Banks of 8 Channel 2 Pole
40-610-022-8/8/2
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
product
PXI High Density Multiplexer, 2-Bank, 80-Channel, 1-Pole
40-615A-009
The 40-615A-009 is a 2-bank, 80-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
product
PXI Single 44 x 4 Matrix 1 Pole Screened
40-523-021-S
The 40-523 module is configured as a 44x4 high density matrix with available reedrelay formats of 1-pole, 2-pole and 1-pole screened. The screened version is suitablefor switching signals up to 50MHz. Model 40-524 is a similar matrix, available insingle pole 46x4 format. Typical applications include signal routing in FunctionalATE and data acquisition systems. These PXI matrix cards are constructed using highreliability Ruthenium Electro-Plated Reed Relays, offering >10e8 operations togive maximum switching confidence with long life and stable contact resistance.
-
product
PXI Single Screened 44x8 Matrix, 1-Pole
40-537-021-S
Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109 operations to give maximum switching confidence with long life and stable contact resistance.
-
product
Distributed Motion Control
ADLINK's Intelligent Remote Data Acquisition & Control Modules (NuDAM) are designed for data acquisition systems based on PCs and other processor based equipment with standard serial I/O ports (RS-232 or RS-485 with auto direction control).The modules convert input/output signals to engineering units and transmit/receive, in ASCII format, to/from any host computer with an RS-232 or RS-485 port. NuDAM modules are the key components in flexible and cost effective remote data acquisition and control systems.
-
product
PXI Very High Density Mux Dual 10 Ch 8 Pole
40-670A-022-D/10/8
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
Ultra-High Vacuum Scanning Kelvin Probe
Our Ultra-high Vacuum Scanning Kelvin Probes (UHVSKP2020 and UHVSKP5050) give the user full access to work function (Φ) and contact potential difference (CPD) measurements under vacuum with the ability to scan a sample area of 20 x 20mm or 50 x 50mm respectively. Each system comes with the UHV head unit, tip amplifier (located at the mounting port), digital control unit and host PC with dedicated software. The tip can be retracted 100mm from the sample and approaches normal to the sample. The associated digital electronic unit powers the head unit and provides an interface between the head unit and the data acquisition system. The system comes with a complete user manual, which includes an introduction to work function measurements and a detailed description of the system software, including examples. The work function resolution of the Ultra-High Vacuum Scanning Kelvin Probes is 1-3 meV.
-
product
Data Loggers
Diversified Technical Systems, Inc.
DTS offers a full line of high performance data acquisition systems, sensors, accessories and software to meet a wide range of critical test requirements. Let the DTS team of experienced engineers and test professionals help you find the right instrumentation for your application.
-
product
PXI Very High Density Mux Dual 10 Ch 8 Pole
40-670A-022-10/8
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI 2A Multiplexer, 1-Bank, 128-Channel 1-Pole
40-614-015
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
Tri-Mode I/O Controller
SAS3808
Broadcom Tri-Mode SerDes technology enables seamless operation of PCIe, SAS or SATA storage devices in a single drive bay. The introduction of PCIe devices executing NVMe to the existing SAS/SATA infrastructure makes industry standard, hot-pluggable drive bays even more versatile. Whether you’re building external or cloud-based storage systems for high connectivity, or outfitting servers, the SAS3808, 8-port, 12Gb/s Tri-Mode SAS/SATA/PCIe Gen 4.0 IOC provides choices for storage optimization by enhancing direct-attached storage (DAS) solutions.
-
product
DynoLAB Test Cell Supervisory System
SAKOR Technologies’ DynoLAB™ data acquisition and control systems offer reliable, cost effective automation of all types of dynamometer test systems. As with all SAKOR products, the DynoLAB system undergoes a continuous program of upgrade and improvement, regularly expanding and enhancing DynoLAB’s capabilities.
-
product
PXI 20 Banks of 4 Channel 2 Pole MUX
40-615-022-20/4/2
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
Universal Data Acquisition System
(UDAS/USB2250)
The Universal Data Acquisition System(UDAS) Sensor Interface provides real world data acquisition for your PC via the USB port. 16 sensor inputs in any mix or combination are accepted by the UDAS. No external signal conditioning is required. The UDAS includes configuration and data acquisition software.
-
product
PXI Dual 16x8 Matrix, 2 Pole Switching
40-532-022
This high-density reed relay matrix with 256 crosspoints. This model is configured as a Dual 16x8, model 40-531 is configured as a 32x8. Both modules are available in a choice of reed relay formats: 1-pole, 2-pole and 1-Pole screened. The screened version can be used for switching coaxial signals up to 50MHz. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering 109 operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules. For example, seven PXI modules will form a 224x8 Matrix, a total of 1792 crosspoints in a 7-slot PXI Chassis.
-
product
Differential Amplifier-per-Channel DAS
System 495
NEFF's System 495 uses a proven widerange, guarded differential amplifier -per-channel technique with a dedicated high-speed analog-to-digital converter for each channel. In addition to storing data locally in memory, a subset of each channel's data can selectively be transmitted to the host for monitoring or recording at an aggregate rate of 1MHz.
-
product
PXI Multiplexer Single 24 Ch 2 Pole
40-632-021-24/2
This series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole, 4-pole and 1-pole screened.
-
product
Single 16x16 1-Pole High-Density PXI Matrix Module
40-520-001
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI Single 32x8 Matrix, 1 Pole Switching
40-531-021
Model 40-531 very high density matrix modules are configured as a 32x8, while the 40-532 modules are configured as a Dual 16x8. Both modules are available in a choice of reed relay formats: 1-pole, 2-pole and 1-Pole screened. The screened version is suitable for switching coaxial signals up to 50MHz. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering 109 operations to give maximum switching confidence with long life and stable contact resistance.
-
product
High-Speed Data Acquisition System
TMX-18
With the TMX-18, there's no need to fumble with awkward buttons or knobs and complicated configurations! The TMX-18 features a high resolution, 17" touch screen display, as well as pre-defined set up options, making test setup a breeze! With the TMX-18, you will be up and running in no time!
