Ground Fault Tracers
find an electrical cable's current leakage or fault.
See Also: Tracers, Curve Tracers, Cable Tracers
-
-
Product
Line Tracer
MI-2093
-
Field proven instrument for under-wall low voltage installation tracing, fuse finding, short-circuit spot determination and metal installation tracing. Accurate fuse locating
-
Product
Ground Resistance
-
Provide accurate and reliable measurements of both ground resistance and soil resistivity for installation and troubleshooting.
-
-
Product
Dual Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-202
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
Ground Set Tester
-
Self-contained, portable convenienceThis tester provides an easy way for an electric utility to check the resistance in protective grounding sets used by line personnel.
-
Product
Semiconductor Curve Tracer
CS-8000 Series
-
The CS-8000 series are equipped with a high-voltage source of up to 5 kV and a high-current source of 2 kA. It features Pulse output, Gate pattern, and very small current measurement capabilities, and it supports the design evaluation of wideband-gap semiconductors such as SiC and GaN.
-
-
Product
Ground Testing
-
Ensuring an effective earth system is essential in a telecommunications system, and Megger is expert in earth testing having been there right from the start. These days Megger offers top end systems for design and soil surveys as well as tough easy to use testers for field engineers. We have tried to make the testers self checking as much as we can, to allow you to concentrate on collating and understanding the results.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
40-203-001
Fault Insertion Unit
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
Tone Generator with Cable Tracer
1RA470
-
Cable tracer is designed to trace wires without damaging the instalations. It has wolume control to increase sensitivity. Power supply is standard 9V battery.
-
Product
Ground Grid Tester
GGT Series
-
The GGT500 ground grid integrity tester is designed for inspection of the substation ground grid. It can also be used as a portable micro-ohmmeter with Both Sides Grounded and Remote Control functionalities. It is intended to inspection the conditions of a grounding system beneath substations, testing of medium- and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links.In the United States when inspecting the quality of the grounding systems beneath a substation, the proper procedure is to inject 300 A DC during a time period of 60 s. This is what the GGT500 will do, and in that time period, the current path and voltage drop are checked. Also acting as a micro-ohmmeter, the GGT500 can test low resistance values by producing high test currents of up to 500 A.The instrument is placed in an unbreakable, plastic case with IP67 protective rating (with closed lid). Although very portable and lightweight, micro-ohmmeters have very high output power capabilities. High output voltage enables a wider measurement range at higher test currents, as well as the use of thinner/longer test cables. GGT500 ground grid integrity tester generates a true DC ripple-free (less than 1 % ripple) current with automatically regulated test ramps. This significantly decreases magnetic transients and ensures great accuracy.When used for testing in Both Sides Grounded conditions, a special current clamp powered from the ground grid integrity tester is used for measuring a current through groundings. If even a higher safety level is required, the remote control feature enables the operator to perform measurements from a distant location, away from the instrument and test object.
-
Product
Fault Simulation
Concurrent Fault Simulator
-
TurboFault combines high performance, versatility and accuracy. It is highly competitive with hardware accelerators for classical test fault grading. It supports synchronous and asynchronous designs at the gate level, including tri-state gates, latches, flip-flops, single and multi-port RAMs, complex bus resolution functions, and User Defined Primitives (UDPs).
-
Product
Ground Resistance Testers
-
IP67 protected top in the industry Test all ground types from Class A to Class D with a single meter Wide 0 to 2000 measurement range Minimize cabling time with innovative earthing rods and cable winder
-
Product
Cable Fault Testers
-
*Compact and lightweight solution for underground cable testing*DC Hi-Pot test of de-energized, shielded underground primary cable*No external power required - self-contained 8kVDC voltage source*Can be used up to a distance of 1500 ft (457m)*Clear and simple test results - analog bar graph and indication of good or faulted cable*Safety feature - measures AC voltage before converting to a DC voltage tester*Lightweight, single hot stick operation for testing cable
-
Product
Semiconductor Curve Tracer
CS-3000 Series
-
*Max. Peak Voltage : 3,000V（HV mode）*Max. Peak Current : 1,000A（HC mode）*Equipped all models with LEAKAGE mode (Cursor resolution 1pA）*USB port for display hardcopy, waveform data (CSV format) and measurement setup SAVE/RECALL*LAN interface for Remote Control
-
Product
PXI Fault Insertion (Fault Injection) Modules
-
PXI Fault Insertion Units (FIU), also known as Fault Injection switch products, are designed specifically for safety-critical applications where the response of a control system is required to be evaluated when sensor connections behave in unexpected ways. These modules are scalable solutions that can be used to switch signals between simulations and real-life devices in a multitude of hardware-in-the-loop (HIL) simulation and test systems. The fault insertion unit can significantly simplify and accelerate the testing, diagnosis and integration work in HIL applications.
-
Product
Ground Resistance Tester
2521
-
Shenzhen Chuangxin Instruments Co., Ltd.
High measuring accuracy, high speed, easy to use, especially suitable for using in laboratory and automatic testing line. Test current AC / 5 ~ 30 (a), resistance Ω (0 ~ 600 m), time (1 ~ 99 s) shows at the same time. Test time can be arbitrary setted. Test alarm value can be arbitrary set up. Pass/fail sound and light alarm.
-
Product
Handheld Grounding Tester
HGT1
-
The HGT1 is a handheld meter to measure ground impedance as well as step and touch voltages. Using the CPC 100 and CP CU1, test currents at variable frequencies can be fed into power cables or overhead lines safely to simulate a ground fault.
-
Product
Visible Fault Locator
FiberLink 6656
-
Fiberlink 6656 Visible Fault Locator is a light-weight, hand-held tool used to quickly troubleshoot faults in the continuity of both single-mode and multimode fibers, especially at fiber launch points or in OTDR dead zones.
-
Product
Earth Ground Meters
-
The earth tester determines ground resistance for both specific and ohm resistances. The earth tester is powered by batteries and have a clock timer function (3 minutes), Data-Hold function, a 3 ½ positions LCD display and their dimensions are 163 x 100 x 50 mm. Resistance ranges come from 20, 200 to 2000 ohms. They have a resolution of 10 / 100 mΩ / 1 Ω. The earth tester measure resistance by means of a constant reverse current (approx. 800 Hz, 2 mA). To measure ground voltage a rectifier is used (5 kΩ/V aprox. 40...500 Hz). The earth tester PKT-2630 series have a small format as well as multiple functions.
-
Product
Underground Fault Location
-
Schweitzer Engineering Laboratories, Inc.
Underground faulted circuit indicators identify the faulted cable section without a time-consuming re-fuse and sectionalize process. Applications include subsurface or pad-mounted transformers, switchgear, sectionalizing cabinets, junction boxes, and splices.
-
Product
Earth / Ground Tester
-
Earth testing covers the testing of earth electrodes and the measurement of soil resistivity. The instrument requirements depend on the range of applications.Ground resistance testing covers the testing of earth electrodes and the measurement of soil resistivity. The instrument requirements depend on the range of applications.
-
Product
Cable Fault Locator
FaultCaster
-
Low Cost Full specification Professional Digital TDR Measures Distances to Open or Short Circuit Faults Extended Measuring Range to 2000m (6000ft) on all cable types Fast-Edge Step TDR technology for improved range & Resolution
-
Product
Board Fault Locator
SYSTEM 8 (BFL)
-
The SYSTEM 8 Board Fault Locator provides the user with the ability to functionally test all common digital ICs in and out-of-circuit. A combination of industry recognised test techniques provides a high level of fault coverage. Additional tools are provided by the SYSTEM 8 Premier software to further enhance the unit\'s wide range of applications.
-
Product
Curve Tracer
CS-5000 Series
-
Maximum peak voltage: 5,000V (high-voltage mode for all models) in CS-5000 Series. Maximum peak current: 1,000A (CS-5300 high-current mode). The CS-5000 Series achieves 5,000V of max. peak voltage with the same physical size as the CS-3000 Series. Best suited for the measurement of a power devices that have 3.3kV and 4.5kV withstanding voltage.
-
Product
Fault Recorder Software
-
The Fault Recorder product family is enhanced with our full suite of software applications designed to simplify the process of configuring our records, retrieving event information and analyzing the results. Tools like our automated event retrieval and expert analysis provide the quickest results when classifying an abnormal event. Detailed fault analysis is easily accomplished with our set of power analysis tools and flexible display options.
-
Product
Ground Resistivity and EarthService Tester
AD-510
-
Large, readable LCD display (2000 counts), Instant battery life indicator, Test frequency: 128 Hz (quartz generator), Test Voltage: max 30 V peak-to-peak, Range: 0,01 W ? 2 k W. Accuracy resistance measurement: 1 % 2 digits,
-
Product
Power Grounding Strap Kit
GS-08
-
The power grounding strap kit ensures safety standards are maintained.
-
Product
Visual Fault Locator
-
OrienTek Optical Technology Ltd.
powerful, mini visual laser source for fiber fault locating. It has attractive design and small size and it is easy to operate. ● Bright red laser at 650nm● Pulsed and CW operation● Outpower: 1mw,10mw,20mw,30mw● 2.5mm universal connector● 40 hours of operation(1mW)● Pocket size design● 1.25 mm adapter for LC (optional)
