Receptacles
receive conductors.
-
Product
AC Power Supply
FC5003
-
Behlman’s FC5003 is a ruggedly built, COTS frequency converter designed to convert 120/208 VAC, 3-phase, 60 Hz, ground power to 115/200 VAC, 3-phase, 400 Hz, aircraft power. The FC5003 is in a rugged 6U (10.5”H) 19 inch rack mount chassis with an input line cord with plug and an output receptacle.
-
Product
HDMI
-
SCHILLER AUTOMATION GmbH & Co. KG
HDMI test adapters and test fixture kits facilitate Source and Sink compliance testing and HDMI cable testing. Our products are used in Certification Testing to CEA 1.3b, 1.4a, 2.0 and 2.1 standards. 1080p and 4K formats are supported. We offer A and D style plug and receptacle connectors, male and female SMA leads, with and without HEAC channels.
-
Product
Host emulator
E84
-
Precision Development Consulting Inc
A USB controlled and self-powered emulator for functional testing SEMI E84 implementations. (E84-1000) This was developed because there was nothing like it in the marketplace, and it was clearly needed. This product enables a factory automation engineer to perform E84 functional testing anywhere in the world. Weighing less than 5oz, it is neither a burden, nor a power hog. You will never need to look for an additional power receptacle in the fab. The emulator gives the user full control over the sequence so that any test can be performed. Existing products were large and unwieldy, and provided canned tests that could not be modified to meet the requirements that Fab managers impose on their suppliers.
-
Product
General Purpose Test Probes
-
Low profile, short travel test probes for restricted space applicationsApplications where long travel is not required such as thin film/hybrid circuits or bareboard PCB testingReplaceable test probe by use of a receptacle
-
Product
High Force Type Prbobe For PCB, K100 Series 100 Mil Pitch, Receptacle With Wire Wrap Pin
KR100-WP
Spring Probe
K100 Series, Pitch 100mil, Receptacle, with wire wrap pin. Brass with gold finish.
-
Product
12-1000V AC Adjustable Non-Contact Voltage Tester
5220A
-
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from12V~1000V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
Product
Extender
3690-12
-
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
Product
Extender
3690-6
-
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
Product
Voltage Testers
-
Electrical Receptacle Tester Instantly Displays Wiring Condition of Any Standard 3-Wire AC 110-120 OutletNeon Indicators Give Positive Indication of Current StatusCompact Unit Simply Plugs into any Standard 3 Wire/Grounded Receptacle (110–125 Volt AC Circuits)Tests for 6 Circuit Conditions: Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse & Correct WiringBlister PackedcULus ListedOrder Qty of 1 = 1 Piece
-
Product
Rugged Rectangular Fiber Connectors
-
TE Connectivity (TE) has a range of rectangular fiber connectors for rugged environments including the ARINC and MTCT connectors. Whether you are designing collision avoidance systems, in-flight entertainment, or air-to-ground communications, you face a challenging economic environment and an ever-increasing demand for weight reduction. TE's ARINC 600 next generation receptacle connector allows you to reduce both weight and costs. TE's MTCT connector is a compact, lightweight design connector for use with ARINC 801 fiber optic termini. Ideal for applications such as avionics, in-flight entertainment systems, communications, production breaks and other areas.
-
Product
PCIe
SFF 8639 Gen4 (U.2)
-
SCHILLER AUTOMATION GmbH & Co. KG
The 8639G4-TPA-PR test adapter or test fixture kit facilitates Source and Sink compliance testing for SFF-Hosts and Devices. These SFF-8639 Gen4 fixtures utilize the multifunctional connector system supporting single/dual port SATA, dual and MultiLink SAS, and/or up to four (4) port PCIe device configurations. The SFF-8639 Gen4 receptacle fixture will accept devices with plug connectors that are in accordance with SFF-8482, SFF-8630, and SFF-8680.
-
Product
High Force Type Prbobe For PCB, K100 Series 100 Mil Pitch, Receptacle
KR100
Spring Probe
K100 Series, Pitch 100mil, Receptacle, no wire wrap pin. Brass with gold finish.
-
Product
DER-075 Double-Ended Receptacle
DER-075
ICT/FCT Probe
Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 130Recommended Travel (mm): 3.30Overall Length (mil): 1,710Overall Length (mm): 43.43Rec. Mounting Hole Size (mil): 53Rec. Mounting Hole Size (mm): 1.35Rec. Mounting Hole Remark: 53 to 55 mil / 1.35 to 1.40 mmRecommended Drill Size: #54 or 1.40 mm
-
Product
Standard Type Spring Probes
-
From for bare board to for ICT, we have variety of spring probes for PCB. In addition to variety of tip type and total length, we also have receptacles that match the best to spring probes. We can also attach lead wire to the receptacles.
-
Product
Universal Test Socket Receptacle
Series 6556
-
Universal Test Socket Receptacle. The Aries Universal Test Socket Receptacle is sturdy, open frame, and easily mounted to PC boards. Allows for easy replacement of Aries and other manufacturers test sockets. A choice of four collet pin styles makes the receptacle useful for any interconnection method.
-
Product
USB-C® – USB 2.0 Receptacle HS SQ Test
AUT17037
-
This product is designed for USB-C USB2.0 Plug Host/Device Electrical Test.
-
Product
Super-Safeway Receptacle Tension Tester
1301270007
-
Super-Safeway Receptacle Tension Tester & Receptacle Tension Tester in Carrying Case
-
Product
Variable Power Supply
VS-10a
-
The VS-10a power supply is a light weight, portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 10 amps, thus the name VS-10a. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-10a is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case.
-
Product
Variable Power Supply
VS3
-
The VS-3 power supply is a very convenient portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 3 amps, thus the name VS-3. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-3 is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case. A unique feature of the VS-3 is that it contains “Magnet Packs” on the back of the case. These “Magnet Packs” can support the VS-3 and allow it to “hang” from any magnetic metal surface. The VS-3 can be powered by our UPS system, eliminating the need for an extension cord. The ability to magnetically attach the VS-3 near the source of connection and eliminating the need for an extension cord makes the VS-3 a “must have tool” for technicians.
-
Product
Torque Tool Testers
Series TT02
-
Series TT02 Torque Tool Testers present a simple and accurate solution for testing manual, electric, and pneumatic torque screwdrivers, wrenches, and other tools. These testers are compact and rugged, suitable for production environments. A universal 3/8” square receptacle accepts common bits and attachments. The TT02 captures peak torque in both measurement directions, and also calculates 1st and 2nd peaks, useful for click-type tools.
-
Product
Receptacle Tester
RT500
-
Designed to detect the most common wiring problems in standard 120V receptacles.Test for correct wiring, open ground, reverse polarity, open hot, open neutral, hot and ground reversed.Conditions NOT indicated: Quality of ground, multiple hot wires, combinations of defects, reversal of grounded and grounding conductors.Large light indicators for greater visibility.Reinforced prongs for increased durability.Push-pull design with slip-resistance ribbing.Made in USA of U.S. and imported parts.
-
Product
12-600V AC Adjustable Non-Contact Wire Tracer
5220
-
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from 12V~600V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
Product
110-125V Receptacle Tester
1938
-
Peaceful Thriving Enterprise Co Ltd
Test for 110-125V AC circuits. Detect faulty wiring in 3 wire receptacle.
-
Product
Circuit Testing
Tester, Circuit GFI
-
*Use to troubleshoot 120 VAC grounded outlets and test GFCI receptacles*Light sequence indicates correct/incorrect wiring*Lifetime Limited Warranty
-
Product
Electrical Receptacle Testers
-
UEi Test & Measurement Instruments
Is a small device containing a power plug and three indicator lights, used for quickly detecting some types of incorrectly-wired electrical wall outlets.
-
Product
Super-Safeway Three Wire Circuit Tester
1301270009
-
Super-Safeway Three Wire Circuit Tester, 3 Indicating Lights & Receptacle Tension Tester in Carrying Case
-
Product
Switch Probes
-
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
Product
230V AC Socket Tester(For UK)
1942
-
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*Test for 230VAC circuits.*Neon indicators.*Detect faulty wiring status in 3 wire receptacle.*Various combinations of 3 neon indicators tell if wiring is OK or 6 possible faulty conditions.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 1W*Frequency: 50Hz
-
-
Product
MU Cable Tester System
16814
-
The MU Locomotive Trainline/Cable Test System (MU Test System) can perform shorts testing, continuity testing, and ground-leakage testing on each of the 27 pin Multi-Unit Trainlines normally found on Freight Locomotives. The MU Test System is comprised of two identical tester units. Each unit is installed in a rugged, water resistant Pelican case. Each unit contains an MU cable receptacle that mates with a 27 pin MU jumper cable. A snap-on vinyl pouch on the outside cover of each unit provides storage for the battery charger/power adapter and the chassis test lead. The enclosure cover hinges separate from the test unit as the cover is opened; this removes the cover completely to allow free access to the MU cable receptacle and the control panel.
