Filter Results By:

Products

Applications

Manufacturers

Shock wave

short moment intense amplitude faster than sound wave

See Also: Wave, Long-Wave IR, Lightwave, Shear Wave, Sub-mm Wave, Microwave, Wavelet, Continuous Wave, Submillimeter Wave, Sine Wave, Millimeter Wave


Showing results: 1 - 13 of 13 items found.

  • Pneumatic Vertical Shock Test System

    KRD11 series - CME Technology Co., Ltd.

    KRD11 series pneumatic vertical shock test system is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and bump test, can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests.

  • Shock Test Systems

    Sanwood Environmental Chambers Co ., Ltd.

    Is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and collision test, can perform conventional half-sine wave, post-peak sawtooth wave, square wave and other waveform shock tests.

  • Pneumatic Horizontal Shock Test System

    KRD12 series - CME Technology Co., Ltd.

    The KRD12 series shock test system is used to measure and determine the horizontal impact resistance of a product or package, and to evaluate the reliability and structural integrity of the test unit in a horizontal impact environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, or trapezoid wave shock test to realize the shock energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.

  • Acoustic Scoring System

    AcoustiScore - Del Mar Avionics

    Provide realistic weapons training. Consisting of a sensor and a data reception and display unit, the system senses the shock waves from passing projectiles and converts these waves into electronic signals for miss-distance measurement and display.

  • Hydraulic Vertical Shock Test System

    KRD10 series - CME Technology Co., Ltd.

    KRD10 series full-automatic hydraulic shock test system is used to measure and determine the impact resistance of products or packaging, and to evaluate the reliability and structural integrity of products in a shock environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests to achieve the shock wave and impact energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure. Windows-based stable control system, full-automatic remote-control interface  Multi-track guide posts combined with good lubricity and noise free hydraulic balance lifting system to achieve stable shifting Automatic control of lifting height with high accuracy and good repeatability Adopts the high strength and hardness cast aluminum table, which has high first-order resonance frequency, featured with low noise and no clutter Built-in brake mechanism to avoid secondary rebound bumps and more secure positioning of the table Multiple waveforms: it can perform conventional half-sine waves, post-peak sawtooth waves, or trapezoid waves One-stop test: built-in test standards meet various requirements to help users to complete test in one stop

  • Pneumatic Vertical Shock Response Spectrum Test System

    KRD14 series - CME Technology Co., Ltd.

    KRD14 series pneumatic shock response spectrum tester is used to measure and determine the shock resistance of electrical and electronic products or packaging, and to evaluate the reliability and structural integrity of the test product in a shock environment. The shock response spectrum is the total result of a series of single-degree-of-freedom linear systems with different natural frequencies subjected to the same shock excitation response. When a product is subjected to an impact, the maximum value of its impact response means that the product has a maximum stress. Therefore, the shock response spectrum tester can better simulate the shock wave and shock energy suffered in the real environment.

  • High-acceleration Shock Tester

    DP-1200-18 - King Design Industrial Co., Ltd.

    The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.

  • Impulse Current Test

    GDCL - HV Hipot Electric Co.,Ltd.

    The impulse current generator is used to inspect the capacity of electric equipment withstand strong impulse current.It is widely used in lightning arrester and shock wave anti-interference test of electric and electronic equipment under their running conditions and used in other research project.

  • Environmental Testing

    DARE Electronics

    Environmental testing capabilities include: High and Low Temperature Testing including Thermal Shock. Humidity Testing to 100% Relative Humidity at High and Low Temperatures. Altitude Testing to 100,000 Feet. Combined Vibration, Temperature and Altitude Testing. Mass Spectrometer for Leak Testing. Vibration Testing to 50 G's and 3000 Hz including Resonance Scan, Cycling, and Endurance. Free Fall Half Sine Wave Mechanical Shock Testing to 100 G's

  • Gas Chromatograph

    Weshine Electric Manufacturing Co., Ltd

    The Oscillator shocks and heats up the oil sample to get the gas from the oil. And then inject the gas sample into the GasChromatograph. Before that,we should use the Air Generator and Hydrogen Generator to fire the FID1 and FID2.The Gas Chromatograph will analysis the gas sample automatically, and you will see the gases components waves on the software on PC.

  • Bump Tester

    KD-163 - King Design Industrial Co., Ltd.

    *Comply with IEC-68-2-29 testing specification(10g/ 16ms、15g/6ms、 40g/6ms、100g/2ms).*Easy installation and simple operation; Low noise; no maintenance required; function holds long.*Well-designed and no resonant-structure, air anti- vibration pad can effectively isolate floor vibration.*Accelerometer adopts repeated measurement and adjustable half-sine wave generator; to control the data is precise.*Magnesium alloy platform is anodized, Servo motor cam to drive, and can adjust the frequency automatically.*The adjustable acceleration value and shock domain is patent design (1ms-13ms).

  • Ultrasonic Bolt Meter - Bolting System

    Mini-MAX-Series - Qualitest International Inc.

    The MINI-MAX, Ultrasonic Bolt Tension Monitor, defines the state of the art in the measurement of the actual elongation produced by tightening a threaded fastener. The MINI-MAX can measure the elongation very accurately in fasteners of virtually any material from 1/2 inch to 4 feet in length. The measurement is achieved by determining the change in the transit time, of an ultrasonic shock wave along the length of the fastener as the fastener is tightened by any method. The on-board microcomputer automatically interprets this time measurement to display the time(nanoseconds), elongation, load, stress, or %strain from stretching a fastener. Through the use of high speed digital signal processing and automated diagnostics, the MINI-MAX minimizes the requirement for extensive operator training. With built in data recordation and reporting through an RS232 interface, the MNI-MAX offers an easy to use and reliable solution to the most difficult bolting problem.

  • The Nanomotor®

    Klocke Nanotechnik

    The patented Nanomotor® is a piezo driven linear motor. It is a multifunctional basic part for many positioning and manipulation devices. It has a positioning stroke of up to more than a centimeter while operating with atomic resolution. The Nanomotor thus bridges eight orders of magnitude. The Nanomotor consists of a cylindrical housing and a slider with a free axial hole inside. It combines high resolution in the sub-nanometer range with a large positioning stroke. The Nanomotor utilizes a piezo tube for fine positioning and a shock wave produced by the same piezo tube for coarse movements. The small Nanomotor is half the size of a match stick. It can lift six times its own mass. Every point of its stroke can be reached with a speed of up to 1 mm/s. The Nanomotor also works in ultrahigh vacuum or even under water. It is driven by a PC card at a supply voltage of only ±15 volts.

Get Help