Control Systems
-
Product
Analog & Digital I/O Modules
-
USB analog and digital I/O modules are a complete family of data acquisition modules for use in process control systems. The analog input modules can measure process signals such as DC voltage, thermocouples, 4-20mA current loops, discrete contact closures.
-
Product
Stand-Alone Programmers
-
Stand-alone programmers are usually based on gang solutions but operate without the need for a host computer to control their operation. This ability is made possible by the integration of a control system within the programmer itself. Stand-alone programmers are ideally suited for use in production facilities where space is restricted and minimal operator interaction and training is desirable.
-
Product
Torque Control System
HD-Series
-
The Mountz torque and automation control system is a revolutionary change in repeatable screw fastening technology. The patented HD-Series hybrid system is the world's first torque control tool using both air and electric power to set and control torque. The HD's precise pneumatic pressure sensor and patented algorithm allow for precision digital torque selection. It provides real-time monitoring and torque control of the tightening process. It provides repeatability of the torque applied to screws, regardless of joint characteristics and frictional differences in actual applications. Affordable, flexible system that can replace up to 8 conventional screwdrivers.
-
Product
Test Hardware
TTPSimulate PCI
-
TTPSimulate supports hardware-in-the-loop simulation and design of complex distributed control systems where some parts of the systems are physically available and others exist only as a simulation model. This board enables concurrent engineering and reliable integration of complex integrated systems in large programs.
-
Product
Multi-Functional Board
PCIe-Harpoon
-
PCIe-Harpoon is a multi-functional board with capabilites for isolated measurement and control. The initial use of the PCIe-Harpoon is to simulate - act as if the PCIe-Harpoon was another piece of equipment. The simulation provides a means to test the rest of the equipment without requiring the real [expensive] asset. In addition the PCIe-Harpoon can provide status and direct software control of the system.
-
Product
PXI Resistor Module 2-Channel 2R to 16.3k
40-293-031
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Experimental Techniques
-
Most Linkam stages work with all standard microscopy setups, but did you know that Linkam’s temperature and environmental control systems can be used for, and with, a wide range of experimental techniques?
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 1.5k
50-265-402
Strain Gauge Simulator
Designed to simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Pressure Meter
ZET 7112-A VER.2
-
The ZET 7112-A VER.2 pressure meter is intended for use in automated process control systems for various industrial applications:
-
Product
Electric Motor QC Systems
-
Megger Baker Instruments designs and manufactures electric motor test systems for original equipment manufacturers (OEMs) that help ensure their motors, generators and coils meet or exceed the quality expectations OEMs set with their customers. Baker motor quality control (QC) systems include the Baker WinAST automated stator tester, the Baker HV WinAST and the Baker WinTATS traction armature test system. Each incorporates the most effective electric motor test processes into a single automated instrument and can be customized to meet the specific testing needs of a given manufacturer.
-
Product
Power System Automation
-
Schweitzer Engineering Laboratories, Inc.
Automate your power system with SEL instrumentation and control devices. Substation automation uses data from IEDs, control and automation capabilities within the substation, and control commands from remote users to control power system devices.
-
Product
Universal Military Craft Systems Controller
3U VPX
-
The system is 3U VPX based. It consists of two CPU modules, a power supply module [SMART.PSU] Technology explained <- Click here, two PMC/XMC carrier modules and two MILBUS modules. Optional: WLAN module for controlling the system externally without hanger access (Aircraft on runway - pre-takeoff)
-
Product
Microprocessors
-
CAES specializes in digital hardware design for commercial and aerospace applications. Our processing solutions are ideal for spacecraft on-board computers, payload processing, nuclear power plant controllers, critical transportation systems, high-altitude avionics, medical electronics and X-ray cargo scanning.
-
Product
X-ray Fluorescence Measuring System
FISCHERSCOPE X-RAY 5000
-
Inline measuring with highest precision for thin films. Robust XRF instrument for measuring and analyzing thin films and layer systems in the running process with connection to the production control system.
-
Product
Wafer Prober
Prexa MS
-
The latest fully automated 300mm wafer prober for memory devices. Featuring high rigidity and exceptional thermal control, the system enables full-wafer contact testing.
-
Product
Video System Controller for Avionics Displays
DP-VME-5400
-
DP-VME-5400 is a Video System Controller for Avionic Displays. It is a VME-based I/O module mainly used to perform video switching and video conversion operations. Applications for this board include display control in air-borne operations and redundancy control.
-
Product
Closed-Loop Servohydraulic Test Bench Control System
-
Closed-loop servohydraulic test bench control system is based on digital devices of ZETSENSOR series with CAN interface. This system has fast response characteristics, high precision, and compact dimensions. The system enables comprehensive control of the servo drive in automated mode in compliance with the set test parameters such as pressure (force), displacement, along with the parallel control of other system parameters such as temperature, pressure, filter plugging, oil pressure, etc.
-
Product
IP Reuse
-
IC Manage Global Design Platform (GDP & GDP-XL) includes an open platform for maximizing IP reuse. Design and verification teams can use the system to rapidly publish and integrate IP into existing flows, and to trace bug dependencies. Internal and third party IP can be imported or linked with IP Central from multiple commercial and open source design management systems, as well as internal revision control systems. ”
-
Product
PXI-2510, 68-Channel, 2 A PXI Signal Insertion Switch Module
778572-10
Fault Insertion Unit
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
Systems for Vibration Monitoring and Diagnostics
-
*Reliable permanent vibration monitoring according to DIN ISO 10816*Cost effective real-time vibration monitoring for machine protection*Increase availability and reliability, reduce maintenance costs and ensure quality*Compact field units and modular control cabinet systems*Analog output and switching output for alarm function
-
Product
Embedded Systems Projects
-
Precision Development Consulting Inc
Module Controller in Track System for silicon wafers, Static Headstack Tester, DOS Device Driver, LED Wafer Prober
-
Product
IOLITE
-
IOLITE - Data Acquisition and Real-time Control SystemData acquisition and real-time control front-end system with dual EtherCAT buses for industrial testing applications. All-in-one solution for real-time control and feedback monitoring.
-
Product
Wireless Remote Control System
Hydra Set
-
Hydra SetPrecision Load PositionerInstalled between the crane (or hoist) and the load, Hydra Set is a valuable positioning device that enables the operator to place heavy objects from 1/2-ton (450 kgs.) up to 250 tons (227,000 kgs.) with 0.001 inch (0.025mm) precision.
-
Product
COM Express Type 6 Compact Module With 7th Gen Intel® Core™ & Celeron® Processor
CEM511
-
The CEM511, a new COM Express Type 6 Compact form factor module, is powered by the latest 7th generation Intel® Core™ i7/i5/i3 processor (Kabylake-U) for high-performance applications. The palm-sized CEM511 is packed with a variety of rich features including low power consumption, industrial wide temperature range support and impressive graphic processing capability. The COM Express® Type 6 Compact module supports two DDR4-2133 SO-DIMM sockets with a maximum system memory capacity of up to 32GB. It has a rugged design with an extended operating temperature range from -40°C to +85°C (-40°F to +185°F) to satisfy different harsh environment demands. The system on module also delivers outstanding computing, graphics and media performance through its Intel® Gen 9 graphics engine, DirectX 12.0, OCL 2.0, OGL4.3 features and 4K resolution (4096 x 2160 @ 30 Hz) support. Therefore, the power efficient CEM511 is designed for graphics-intensive applications over the Industrial IoT, including industrial control system, medical imaging, digital signage, gaming machines, military, and networking.
-
Product
Automated Control System for Veneer Edge Gluing Line
Vikat
-
The automated veneer splicing line control system is designed to identify defective veneer areas, control the scrap trimming, bonding of suitable areas and the formation of output sheets of a given size.
-
Product
VPX Computer
CRS-D5I-3VC1
-
Abaco Systems CRS-D5I-3VC1 Rugged COTS System is a packaged pre-validated 5-slot video processing, display and control computer system fully integrated and ready to be deployed as soon as your application is ready.
-
Product
System Integration Services
-
Systems integration services to meet a wide variety of industrial needs. It includes the following key expertise: Desktop, Embedded Simulation and Real-time system, Data Acquisition and Report generation/extraction, Factory automation, Testing, Control and Monitoring system, Vision inspection, Equipment calibration, Special purpose machine, and many more.
-
Product
Dissolution Software for Enhanced Data Management
-
Agilent dissolution software systems enable more effective management and analysis of dissolution data, while ensuring ongoing regulatory compliance. Our dissolution testing data systems integrate analysis and sampling and provide real-time access to test status and simultaneous control of multiple systems.
-
Product
RS-422/RS-485 Repeater
ND-6510
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
Seismic Impact Control System
ZET 048
-
Seismic impact control system is used to control ground surface shifts caused by earthquakes, explosions and other natural or technology-related factors. Seismic control system is used to obtain actual information of the seismic environment as well as for process facilities state monitoring (in particular, for petroleum industry pipelines systems control).
