Signal Conditioning
The processing of signals to reduce noise level, amplify, attenuate, or otherwise condition.
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Generators, Signal Meters, Signal Conditioners
-
Product
Digital/Analog/Frequency Measurement Module
JT 2149/DAF
-
The JT 2149/DAF is a compact, mixed-signal (Digital/Analog/Frequency) measurement module for use in JTAG Technologies’ widely-used JT 2147 (QuadPod) signal conditioning interface. The DAF module has been designed to replace a regular TAP Pod and provides 28 measurement channels plus a clock generator. When connected to a circuit board via edge connector or test fixture/jig test pins, the module enhances standard digital boundary-scan tests by enabling a series of analog and frequency measurements to be made.
-
Product
Downconverter
DOWNCONVERTER 10 GHz VXI
-
The DOWNCONVERTER 10 GHz design assumes its use in closed mobile complexes for field testing of communications equipment. To do this, the device has applied advanced solutions to reduce the phase noise of the output signal in conditions of increased vibration and temperature. The device has a temperature-stabilized reference frequency generator with the ability to output a reference frequency signal. Also, it is possible to operate from an external reference generator.
-
Product
LVDT Sensor Amplifiers
-
Analog Devices signal conditioning ICs, together with linear variable differential transformers (LVDTs), can be used to convert mechanical position to a dc voltage. The IC provides both the excitation for the LVDT and the output conversion to dc level with a user selectable gain. ADI LVDT signal conditioners are available to interface with a wide range of LVDTs, including half bridge and standard 4- and 5-wire.
-
Product
PCI-6229, 32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO PCI Multifunction I/O Device
779068-01
Multifunction I/O
32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO PCI Multifunction I/O Device - The PCI-6229 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Submersible Extensometers
Model 4030
-
Jinan Testing Equipment IE Corporation
The Model 4030 extensometer uses a special LVDT-like sensor to measure strains on samples submersed in water or other compatible liquids. The unit is provided with the signal conditioning electronics. The extensometer is a semi-custom design, which is available in smaller measuring ranges up to 5 mm (0.2 inches). Clip-on (COD) style designs are also available.
-
Product
PCI-6221, 16 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO PCI Multifunction I/O Device
779066-01
Multifunction I/O
The PCI-6221 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXI-6280, 16 AI (18-Bit, 625 kS/s), 24 DIO, PXI Hybrid, Multifunction I/O Module
779120-01
Multifunction I/O
16 AI (18-Bit, 625 kS/s), 24 DIO, PXI Multifunction I/O Module—The PXI‑6280 offers analog input, correlated digital I/O, two 32‑bit counter/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Analog Functions
-
Analog Devices designs amplifiers and linear products that deliver high performance and high value. We combine circuit design, manufacturing process innovation, and applications expertise to create products that simplify signal conditioning design.
-
Product
3-Slot Data Acquisition Mainframe With Three 20-Channel Multiplexer Modules
DAQ970MB
Mainframe
The DAQ970MB Good Multiplexer Bundle offer includes a DAQ970A three-slot data acquisition mainframe and three 20-channel DAQM901A multiplexer modules. This bundle provides the following:3-slot mainframe with USB and LAN6.5-digit (22-bit) internal DMM60 channels of multiplexer switches6 channels of dedicated current measurements2- and 4-wire scanning300 V switching80 channels/s scanningbuilt-in thermocouple reference junctionbuilt-in signal conditioning to measure thermocouples, RTDs and thermistors, AC / DC volts and current; resistance, frequency / period, diode test, and capacitance
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
779521-01
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
Mass Flow Controllers for Gases
-
Sensirion''s mass flow controllers are characterized by fast and accurate control of gas flow over a wide dynamic range. Based on the innovative CMOSens Technology, the heart of these mass flow controllers is a calorimetric microsensor (MEMS), which is integrated with the complete signal conditioning electronics on one single chip. While the flow is measured using the thermal measurement principle, efficient control is provided by an analog controlling circuit. This unique integrated technological approach results in excellent performance and reliability - at a very attractive cost.
-
Product
NI-9234, 4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module
779680-01
Sound and Vibration
4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module - The NI‑9234 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The NI‑9234 is also compatible with smart TEDS sensors. The NI‑9234 delivers a wide dynamic range and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
Product
Auto Calibration for Load & Extensiometer
-
Jinan Testing Equipment IE Corporation
TE electronic calibration module provides an easy way to calibrate load cell or extensometer and signal conditioning electronics without using a mechanical calibrator. It enables performing on-site electrical calibration and easy to periodically “spot check”, which will help ensure that the load cell and the extensometer and electronics are calibrated correctly.
-
Product
Full-Featured Thermocouple and Voltage Measurement Instruments
EX10XX Series
-
A wide range of measurement types, including pressure, strain, temperature, position and voltage, can be performed using this instrument when combined with the EX10SC signal conditioning expansion chassis. Each input incorporates an independent signal conditioning path with software selectable filters for maximum flexibility.
-
Product
RF Signal Generators
RF Signal Generator
RF Signal Conditioning provides signal manipulation capabilities for high-frequency or broadband signals. You can use these products to augment the capabilities of connected instruments to improve attributes like accuracy and frequency range.
-
Product
RS-422/RS-485 Repeater
ND-6510
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
VXI Module
VDSP-31
-
The VDSP31 is a VXI based, multi-channel data acquisition system and digital servo control module. The VDSP31 offers a complete solution for high performance closed loop applications. The VDSP31 has been designed to solve specific problems related to the control of hydraulic actuators. Signal conditioning modules can be combined on a per channel basis to configure the VDSP31 for load or displacement feedback.
-
Product
Data Acquisition PCI Card
UPC2100
-
The UPC2100 PCI Sensor Interface card provides real-world data acquisition and control for your PC. Up to 16 sensor inputs in any mix or combination are accepted by the UPC2100. No external signal conditioning is required. The UPC2100 includes configuration and data acquisition software and is compatible with C#, .NET, C++, Visual Basic, LabView.
-
Product
Modbus RTU Analog Input
-
Provide direct connection to a wide variety of sensors to any host with an RS232 or RS485 port. The modules perform all signal conditioning, scaling, linearization, and A/D conversion. They each contain some discrete digital I/O lines and can measure signals such as:
-
Product
PXIe-4497, 204.8 kS/s, 114 dB, 2 Gains, AC/DC-Coupled, 16-Analog Input PXI Sound and Vibration Module
781369-01
Analog Input Module
204.8 kS/s, 114 dB, 2 Gains, AC/DC-Coupled, 16-Analog Input PXI Sound and Vibration Module - The PXIe‑4497 is designed for high‑channel‑count sound and vibration applications. With 24-bit analog inputs and IEPE constant current signal conditioning, the PXIe‑4497 is ideal for making precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. The PXIe‑4497 delivers simultaneous sample on all channels. In addition, the module includes built-in antialiasing filters that automatically adjust to your sample rate, software-selectable input gain, and TEDS smart sensor support for error-free setup. Common applications include noise, vibration, and harshness (NVH) analysis; large microphone arrays; and dynamic structural test.
-
Product
Bit Error Rate Tester
iBERT Series
-
Provide a range of signal conditioning and BER analysis from 1.5 Gb/s to 40 Gb/s on 1-4 channels and deliver the test and measurement industry''s broadest serial communications test portfolio of bit error rate tester products.
-
Product
IEPE Signal Conditioning Amplifiers
-
Although IEPE (Integrated Electronics Piezoelectric) sensors is not a new technology there are a wide variety of applications where the measurement instrumentation is not configured with IEPE signal conditioning built in. In these situations it is necessary for the IEPE supply to be provided by an external source. Usually this type of instrument will also provide th user with the option to add gain to the signal being conditioned. The Kemo range of IEPE signal conditioning instruments can be used as stand alone conditioners/amplifiers are many of them can also be integrated with filters.
-
Product
Low Noise Accelerometer Cables & Coaxial Sensor Cables
-
Our cable assembly team in the UK produce the highest quality cable assemblies for use with a wide range of sensing and measurement applications. By making the cable assemblies in our own factory we are able to ensure the quality of every connection and every assembly, each cable is fully tested and its capacitance checked. Due to our experience in signal conditioning we understand the critical elements to quality signal analysis, this includes the correct cable. This is particularly true for accelerometer cables and sensors cables which can introduce significant noise issues if not used correctly.
-
Product
2 to 8 Channel Anti-Alias Low-Pass Filter Card
AAF-1
-
The AAF-1 is a multi-channel anti-alias low-pass filter board designed for front-end signal conditioning in PC-based or stand-alone 12-bit A/D conversion systems.
-
Product
JTAG Boundary-Scan Controller for PXI and PXI-Express 'Hybrid' Slots or Plug-In Controller for PXI-Express Peripheral Slot
JT 37x7/PXI
Controller
High speed and performance JTAG Boundary-scan controller for PXI and PXI-Express ‘hybrid’ slots or plug-in controller for PXI-Express peripheral slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘
-
Product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781209-01
Strain/Bridge Input Module
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
Product
Multi-Channel Attenuation Control Unit (4-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7204B
Attenuator
The J7204B is a multi-channel (4-channels) attenuation solution for signal attenuation and conditioning of up to 4 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7204B reduces cost of ownership and provide the best measurement accuracy.
-
Product
USB to RS-422/RS-485 Converter
ND-6530
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
Block Up-Converter
-
RF Lambda’s block up-converters are used to convert IF frequencies up to RF. They can include power amplifiers for high output power and signal conditioning such image rejection as required by the system.
-
Product
IOLITE LX
-
IOLITE LX - Embedded Data Acquisition SystemIOLITE LX is an embedded data acquisition system based on a low power Linux based ARM processor with open architecture being able to act like a data logger, real-time system, and signal conditioning frontend, all at the same time.
