Electrostatic Field
is a stationary charge that is time invariant.
-
Product
Near Field Micro Probe ICR HV H Field
-
The measurement coil is located vertically in the probe head. The near field probes are run with a positioning system (Langer Scanner).
-
Product
Field meters
-
Small, lightweight and low priced non frequency selective Efield meter. It can be used for relatively high field strengths e.g. to observe the field in a TEM cell or a strip line.
-
Product
Complete Field Meter Site Testing Solution
7 Series
-
We raised the industry standard by introducing the PowerMaster 7 Series as a true 3-phase analyzing reference standard with internal 3-phase current and voltage source capability. The innovative design of the PowerMaster® 7 Series allows utilities to fully test a metering installation with one piece of equipment. Customer load meter testing, phantom load meter testing, CT burden and ratio testing, CT de-magnetization, PT ratio testing, and transducer testing can all be performed with one solution. In addition, vector diagrams, voltage and current waveforms, and harmonics data up to the 100th harmonic can all be analyzed to complete a true wiring verification.
-
Product
4 Digit Field Indicator
CFIA-40 4
-
1. Using LED to display, and able to be used in dark environment2. No external power needed3. Able to display measured value like pressure , temperature and depth etc4. Display solution 1/99995. Isolated alarm open drain output6. Voltage drop will below 4 volt
-
Product
On-Site Field Testing & Evaluation
-
MET is a highly-regarded resource for electrical inspection agencies within the United States and Canada to assure compliance of unlabeled equipment in the field. Field evaluations are performed by MET Laboratories on unlisted equipment to support the Authority Having Jurisdiction.
-
Product
Field Master 3 Electric Fence Charger
FM-3
-
Parker McCrory Manufacturing Co.
Power to stop the most stubborn stock! For small to medium pastures. The all new low impedance model for small to medium pastures features advanced solid state circuitry. Shocks through wet weeds and brush. New color coded fence and ground terminals. Red to the fence and Black to ground. Fuse protection, with built-in lightning arresters. Full 3 year warranty covers damage caused by lightning.
-
-
Product
Rotary Field Direction Indicator According to DIN EN 61557-7 (VDE 0413-7)
-
PeakTech Prüf- und Messtechnik GmbH
Direction indicators are indispensable for use in the electrical assembly of three-phase motors. This offers two different functions for displaying the direction of rotation. I
-
Product
Near Field Probes 30 MHz up to 3 GHz
RF2 set
-
The RF2 near field probe set consists of 4 passive near field probes for measurements in the development phase of the magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF2 set allow the step by step localization of interference sources of the RF magnetic field on assemblies. From greater distances the electromagnetic interference can be detected by RF-R 400-1 and RF-R 50-1 probes. The RF-B 3-2 and RF-U 5-2 probes with their higher resolution can more precisely detect the interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
Product
Free DR and High Field Magnet in Shared Vacuum Space
-
50 mm 4 K magnet bore, 30 mm sample space in DRSuitable for use with Leiden DR type CF200, CF450, CF650 or CF1000 DR
-
Product
Field Simulation Software
QuickField™
-
QuickField™ is a very efficient Finite Element Analysis package for electromagnetic, thermal, and stress design simulation with coupled multi-field analysis.
-
Product
Vehicle Electromagnetic Field Exposure Test System
SEM-400
-
Beijing KeHuan Century EMC Technology Co,.LTD
Vehicles are our daily public transportation. Electromagnetic pollution in vehicles has attracted more and more public attention. The newly revised compulsory standard GB27630-201X "Passenger Car Air Quality Evaluation Standard" intends to require the electromagnetic field in the car as one of the indicators, according to GB/T37130-2018 "Measurement method of vehicle electromagnetic field relative to human exposure" The measurement method is to measure the intensity of the magnetic field in the car. In the frequency range of 10Hz-400kHz, the electromagnetic field measurement result should meet the public limit requirements of GB8702-2014 for electromagnetic exposure.
-
Product
Power Frequency Magnetic Field Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Power frequency magnetic field simulator is a special designed instrument with high reliability according to the features of the power frequency magnetic field immunity test for electrical and electronic products.
-
Product
AC Hipots for Factory and Field Testing
HPA Series
-
HPA Series test sets perform AC withstand and PD testing (most models) on higher capacitance loads, offering up to 40 kVA and 300 kV AC
-
Product
Vector Field and Multi-Axis Systems
-
Cryogenic vector magnet systems allow precise alignment of the magnetic field to an exact direction in a measurement sample. The system provides the capability of orienting the magnetic field to any vector direction. This is suitable for experiments where samples cannot be moved easily.
-
Product
Polarisation Mode Field Diameter
MA500
-
MA500 is our polarisation mode field diameter (MFD) and effective area (Aeff) measurement system, specially designed to measure large effective area and high NA single mode fibers with its enhanced dynamic range and high-resolution scanning optics.
-
Product
Near Field Probes 30 MHz up to 3 GHz
RF1 set
-
The RF1 near field probe set consists of 4 passive near field probes for making measurements in the development phase of E-field and magnetic field in the ranges of 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF1 set allow for measurements close to the electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors in order to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
Product
Electrostatic Discharges
ESD3000
-
ESD3000 is the only ESD generator in the market using standard AA batteries to offer full flexibility to the user to replace them when needed.
-
Product
Field thermal needle system for thermal resistivity / conductivity measurement
FTN01
-
Hukseflux Thermal Sensors B.V.
The FTN01 Field Thermal Needle System allows performing fast, on-site measurements of the thermal resistivity or conductivity of soils, in particular around the typical depth of burial of high voltage cables. FTN01 is designed with a focus on robustness and saving time, while still offering sufficient accuracy for typical field measurements. The sensor is a Non-Steady-State Probe (NSSP), TP09, which is mounted at the tip of the Lance LN01. The system is operated using a hand-held Control and Readout Unit CRU01.
-
Product
Flat Field and Imaging Gratings - Type IV
-
HORIBA Scientific produces a wide range of holographic master gratings from which high precision replicas are manufactured.Type IV aberration-corrected flat field and imaging gratings are designed to focus a spectrum onto a plane surface, making them ideal for use with linear or 2-D array detectors.These gratings are produced with grooves that are neither equis-paced nor parallel, and are computer optimized to form near-perfect images of the entrance slit on the detector plane.
-
Product
HEVC H.265 Field Strength Meter & TV Analyser
HD RANGER 3
-
The RANGER Neo 3 is a professional Field Strength Meter and Spectrum Analyzer that is part of a new breed of multifunction, TV, Satellite, CATV and WIFI analyzers.
-
Product
Electrostatic Discharge Generator
-
Beijing KeHuan Century EMC Technology Co,.LTD
Electrostatic discharge generator
-
Product
Scanning Near Field Optical Microscope
SNOM
-
SNOM microscopes employ SPMs precision of piezoelectric raster-scanning together with sharp probes to obtain light optical images at rather better than the usual wavelength-limited resolution. The possibility to go beyond the Abbe diffraction limit has been achieved with the Near-field light optical microscopes (SNOM or NSOM).
-
Product
Magnetic Field Sensors
-
Our cylinder sensors for pull rod cylinders can be integrated into many applications. They are mounted with mounting brackets on cylinders with tie rods and DUO rails. The concept is suitable for the most common types of cylinders with any piston diameter. Features: contact-free detection of the piston position, tie rod Ø up to 17 mm, reliable switching behavior, wear-free, resistant to dirt, secure grip, easy installation.
-
Product
Multifunction Field Calibrator & Communicator
MC6-Ex
-
The MC6-Ex is an intrinsically safe field calibrator and communicator. It is ATEX and IECEx certified and can be used in all hazardous zones / divisions. The MC6-Ex includes a field communicator for HART, FOUNDATION Fieldbus and Profibus protocols. Each calibrator is delivered with a traceable, accredited calibration certificate as a standard. t is a documenting, multifunction calibrator and communicator that offers calibration capabilities for pressure, temperature and various electrical signals.
-
Product
Impulse Magnetic Field Immunity Tester
IMF61000-9
-
IMF61000-9 impulse magnetic field immunity tester is high performance test instrument which special designed for to do impulse magnetic field immunity test and fully meet IEC61000-4-9, EN61000-4-9 and GB/T17626.9 standards, also it come with high intelligent, high stable performance and easy operation characteristics.
-
Product
Universal Field Calibrater
UFC 45-B
-
Model UFC-45-B field calibrater is widely used calibration tool in process industry for last 15 years. Functionally it is designed to tackle most common trouble-shooting during commissioning and routine maintenance. Model UFC-45-B is truly hand held calibration instrument purposely limited functionally to simplify its use. With all its features UFC-45-B battery operated field calibrator is an essential tool in a service engineers kit.
-
Product
Field Management
-
EAG offers field-to-final report project management for studies to demonstrate human and environmental safety. As on-site study directors, our Field Managers bring decades of study design, protocol development, analytical oversight, and GLP/QA compliance expertise across a variety of field management study types. In addition, EAG’s access to a broad network of field sites across the United States and Canada ensures that we can deliver the test system, soil characteristics and geography necessary for just about any regulatory need.
-
Product
Impact Echo SystemFor Field Evaluation of Concrete Structures
Vu-Con System
-
The Vu-Con Analyzer provides the engineer with the sturdiest, most reliable system for impact echo analysis. No moving parts and implementation of the latest microcomputer technology has created a system that is both sophisticated and reliable. The unit comes with a 90 mm (3.5?) by 115 mm (4.5?) graphic display screen that is easily viewed in daylight
-
Product
Near Field Probes
-
A typical emi emission test is performed using broadband EMC antennas such as biconical, log periodics, Combilogs and horns. These antennas usually placed at 1, 3 or 10 meter distance as required by the test specification. These is considered far field measurements and the emission limits are given for the specific distance by the specification. During EMI compliance measurements, the emissions levels from products are compared with these limits. If the product exceeds these limits it is considered failing. These tests are typically conducted in a open area test site IOATS) or inside an anechoic chamber.
