Product

Four Channel Low-Noise DC Bias Card

PI-41702

-

Pulse Instruments

PI-41702 - Pulse Instruments

The PI-41702 is a four channel bipolar DC Bias supply that can provide an output current up to 100 mA per channel. The output voltage ranges from –8 V to +8 V, and this card has special filter circuitry to reduce the output noise for those applications that require a low noise bias output. Additionally there is a ‘D’ type connector that allows the introduction of laboratory type supplies to reduce the noise further. To change from using the internal power supplies to external power supplies requires repositioning jumpers. The PI-41702 also has voltage and current sense for remote measurement of the voltage and current levels.

Product

Stand Alone Power Supply

-

CAEN S.p.A.

CAEN S.p.A.

CAEN has developed a new line of fully independent Desktop and Rack-Mount High Voltage Power Supplies. Offered with various V/I output configurations, CAEN Desktop and Rack-Mount Power Supplies are flexible enough to bias a wide range of detector types.

Product

Bias Boards

CUBE

-

XGLab S.R.L.

CUBE - XGLab S.R.L.

The CUBE Bias Boards are a set of off-the-shelf biasing boards developed to speed-up the integration process of the CUBE CMOS preamplifier family of XGLab. These boards allow to bias both the detector (SDD as standard, other detector upon request) and the CUBE preamplifier.

Product

Operational Amplifiers

-

ams-OSRAM AG

ams-OSRAM AG

Operational amplifiers from ams are ideally suited to audio applications. These CMOS devices are available as single, quad or differential amps. They feature good common-mode rejection, have low input bias currents, good gain bandwidth, low total harmonic distortion and an excellent rail-to-rail output-drive capability of 200mA peak.

Product

SSPAs / LNAs / Broadband

-

Nanowave Technologies Inc.

Nanowave Technologies Inc.

SSPAs based on the latest Galium Nitride (GaN) technology offer the best combination of high peak powers, high reliability, high efficiency, and soft degradation. High efficiency and high power are hallmarks of GaN technology, enabling SSPAs to challenge traditional tube-based amplifiers across the design spectrum. In addition the long lifetime from these devices, combined with the gradual degradation should individual devices fail, provide unparalleled service lifetime. Techniques such as bias modulation and linearization provide even better prime-power efficiency while still meeting the demanding requirements of pulsed or CW applications.

Product

LCR Meter

ET/QuadTech 1910/1920

-

IET Labs

ET/QuadTech 1910/1920 - IET Labs

The 1920 1 MHz LCR Meter is the most popular and designed to perform capacitance and impedance measurements on a variety of electronic components and materials over a frequency range from 20 Hz to 1 MHz. The1920 features programmable bias voltage from 1 mV to 2 V for biasing capacitors and other semiconductor devices during measurements.

Product

DC Bias Current Power Supply

TH1775

-

Shenzhen Chuangxin Instruments Co., Ltd.

TH1775 - Shenzhen Chuangxin Instruments Co., Ltd.

TH1775 is a DC Bias Current Source (or DC Magnetization Current Source) used for inductance measurement of inductors and transformer windings with DC bias current. Except for constant current output, low additional error and wide frequency response range are important for bias current inductance measurement. High frequency LCR meter could be used, when the frequency response range is wide enough. MPU controlled auto current balance technology is adopted to realize AC+DC current overlap and constant current output from 0 to ±20A. Two TH1775 can be paralleled to supply a maximum current up to 40A.TH1775 permits high frequency measurement up to 1 MHz and can be directly controlled by TH2816A, TH2817A, TH2818 and TH2819. TH1773/TH1775 with its low additional error, wide frequency response range and sweep output function is widely used in DC biased inductance measurement. TH1775 also provides a perfect solution for magnetic material analysis.

Product

NIM Power Supplies And Bins

-

ORTEC

ORTEC

ORTEC offers two types of power supplies for use with NIM instrumentation: power supplies that provide operating voltages for a detector (more properly called detector bias supplies or “HV” supplies) and power supplies that provide the necessary operating voltages for NIM Modular electronic instruments in the form of a NIM “Bin” with associated power supply.

Product

DC Bias Passing Attenuators

-

JYEBAO Co., Ltd.

JYEBAO Co., Ltd.

Passes DC while also attenuating the RF signal.

Product

Transmitter (Export Only)

SMB

-

Lectrosonics, Inc.

SMB - Lectrosonics, Inc.

The input section features the unique servo bias input circuitry with a standard TA5M type jack for use with electret lavaliere mics, dynamic mics, or line level signals. A DSP-controlled analog audio limiter is employed before the A-D converter. The limiter has a range of more than 30 dB for excellent overload protection and a dual release envelope that makes the limiter acoustically transparent while maintaining low distortion. The limiter recovers quickly from brief transients, with no audible side effects, and also recovers slowly from sustained high levels to keep audio distortion low while preserving short term dynamics.

Product

Analog Control Cable for Electronic Loads

EE105T-xx

-

Executive Engineering

EE105T-xx - Executive Engineering

The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input

Product

Master Oscillator Multiplexer

MOX Series

-

EM Research, Inc.

MOX Series - EM Research, Inc.

*Low phase noise OXCO *Interface between VSAT Modems and Frequency Converters *Robust housing is gasket sealed for weather resistance *OCXO iwth low G-sensitivity available *Single or dual multiplexer *Single or dual bias tee *Available in various OCXO frequencies: 10, 50, 100, 120 MHz

Product

SQUID Electronics

XXF-1

-

Magnicon GmbH

XXF-1 - Magnicon GmbH

It is designed to satisfy the needs of nearly all low-Tc SQUID applications. Additional integrated current sources provide e.g. bias current and calibration pulses for TES applications. These current sources together with an additional switchable feedback path make two-stage SQUID operation very convenient.

Product

Cost-Effective ATE System

PRO RACK ATE

-

Qmax Test Technologies Pvt. Ltd.

PRO RACK ATE - Qmax Test Technologies Pvt. Ltd.

Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.