Product

Tunnel Diode Zero Bias Detectors

-

Pasternack Enterprises, Inc.

Pasternack Enterprises, Inc.

A tunnel diode zero-bias detector is a device that converts microwave and millimeter-wave radio frequency (RF) signals into a DC voltage without requiring an external power source

Product

DC BIAS CURRENT UNIT

3265B SERIES

-

Wayne Kerr Electronics, Ltd.

3265B SERIES - Wayne Kerr Electronics, Ltd.

To evaluate components at currents up to 125 A the 3265B DC Bias Units are used with either the Wayne Kerr 3255B series of Inductance Analyzers or the 3260B Precision Magnetics Analyzer. When one 3265B/25A or 3265BQ/25A DC Bias Unit is connected to an instrument up to 25 A of DC bias current can be set in steps of 25 mA with one unit. Additional DC Bias Units can be added such that with five units connected in parallel it is possible to set DC bias currents up to a maximum of 125 A DC.

Product

RF Power Amplifiers

-

Pasternack Enterprises, Inc.

Pasternack Enterprises, Inc.

RF power amplifier category from Pasternack have components packaged in a hermetically-sealed metal enclosures and exhibit outstanding performance in high gain, gain flatness, high linearity and wide dynamic range. RF power amplifiers have excellent performance by using a hybrid microwave integrated circuit design and advanced GaAs pHEMT components. These SMA power amplifier modules are unconditionally stable and include built-in voltage regulation, bias sequencing, and reverse bias protection for added reliability.RF power amplifier over-voltage protection is installed externally for easy repair. These high reliability radio frequency power amps are fully matched internally for 50 Ohm input and output. This 50 Ohm power amplifier matching helps eliminates the need for any additional sensitive external RF tuning components.Our power amps are ideally suited for high linearity applications. These radio frequency power amplifiers offer small signal gain over a temperature range. The Pasternack RF power amplifiers have excellent gain flatness ranges and the IP3 output performance.Most all Pasternack RF power amplifiers are EAR99

Product

Broadband Detectors

-

Pacific Millimeter Products

Pacific Millimeter Products

These waveguide bandwidth detectors use silicon beam lead diodes on a planar stripline circuit to obtain an extremely rugged and compact device. Most millimeter wave broadband detectors have very poor VSWR due to the difficulty in obtaining a good wideband impedance match to the diode. To overcome this problem, these detectors utilize two diodes and an internal matched termination and 3 dB hybrid as shown below. This circuit allows a VSWR of 2.0 or better over a full waveguide bandwidth for most of these detectors. Detectors for waveguides WR-8 and smaller use a single zero bias GaAs diode. The high sensitivity zero bias GaAs diodes can also be special ordered for use at lower frequencies when highest sensitivity is required.

Product

Analog Control Cable for Electronic Loads

EE105T-xx

-

Executive Engineering

EE105T-xx - Executive Engineering

The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input

Product

Tactical Grade Inertial Measurement Unit (IMU)

ADIS16490 iSensor

-

Analog Devices Inc.

ADIS16490 iSensor - Analog Devices Inc.

The ADIS16490 iSensor® device is a complete inertial system that includes a triaxial gyroscope and a triaxial accelerometer. Each inertial sensor in the ADIS16490 combines industry-leading iMEMS® technology with signal conditioning that optimizes dynamic performance. The factory calibration characterizes each sensor for sensitivity, bias, alignment, and linear acceleration (gyroscope bias). As a result, each sensor has its own dynamic compensation formulas that provide accurate sensor measurements. The ADIS16490 provides a simple, cost-effective method for integrating accurate, multiaxis inertial sensing into industrial systems, especially when compared with the complexity and investment associated with discrete designs. All necessary motion testing and calibration are part of the production process at the factory, greatly reducing system integration time. Tight orthogonal alignment simplifies inertial frame alignment in navigation systems. The SPI and register structure provide a simple interface for data collection and configuration control.

Product

RF & Microwave Passive Components

-

SHF Communication Technologies AG

SHF Communication Technologies AG

SHF’s microwave components are broadband devices suitable up to 110 GHz. Our SHF BIAS TEES are well known but perhaps a slight variation does suit your application even better. DIPLEXERS are bias tees with a certain bandwidth in the low frequency path to combine or separate high frequency and low frequency signals into or out of a single line. DC-FEEDERS are bias tees without the capacitor. Therefore, it provides slightly lower insertion loss in case it is connected to an AC-coupled device which already has a capacitor on its input. Based on our air line construction, these passive components provide resonance-free transmission over the entire operating range.

Product

RF Amplifiers Bias Controllers

-

Analog Devices Inc.

Analog Devices Inc.

RF amplifier bias controllers generate a regulated drain voltage and actively adjusts the gate voltage of an external amplifier to achieve constant bias current. It can be used to bias any enhancement and depletion type amplifier operating in Class-A regime with drain voltages (VDRAIN) as specified. These devices achieve excellent bias stability over supply, temperature and process variations, and eliminates the required calibration procedures used to prevent RF performance degradation due to such variations.

Product

PSD Signal Processing Tool

SEEPOS

-

SiTek Electro Optics AB

SEEPOS - SiTek Electro Optics AB

For most position measurement applications the SiTek SEEPOS system offers a complete and easy-to-use solution. High speed PSD electronics combined with digital signal processing and high speed USB data transfer gives a powerful measurement system. With its large dynamic range it can handle light powers from nW to mW from DC light sources as well as modulated light sources. All parameters, such as PSD bias voltage, amplifier gain, the use of analog and digital filters etc., are easily controlled from the included software and light spot position is continuously displayed both in XY and X-t, Y-t graphs. Optimized plot algorithms ensure that all data is visually seen on the screen even in full speed measurements. Included tools for data analysis and visualization simplify rapid scan through large data sets in order to find specific parts of interest.

Product

PRECISION MAGNETICS ANALYZER

3260B SERIES

-

Wayne Kerr Electronics, Ltd.

3260B SERIES - Wayne Kerr Electronics, Ltd.

At the design stage of component development it is vitally important to understand how the component performs under different operating conditions. This might include operation at diverse frequencies, AC drive levels or DC bias currents.

Product

Biased and Unbiased HAST Testing

-

Reltech Limited

Reltech Limited

Considered within the semiconductor industry as the fast and effective alternative to Temperature Humidity Bias testing (THB), Highly-Accelerated Temperature and Humidity Stress Test (HAST) is a critical part of the device package Qualification process and is used to evaluate the reliability of non-hermetic packaged devices in humid environments.

Product

GPS over Fiber

-

CCI

CCI

*High Dynamic Range GPS to Fiberoptic Transmitter and Fiberoptic to GPS Receiver*Compact NEMA rated outdoor Fiber Transmitter provides +5VDC Bias for GPS Antenna LNA*Rack mounted Fiber Receiver provides 8 RF outputs and integrated monitoring and alarming*Cost effective solutions for distribution of GPS signal over long distance

Product

DC Bias Injector

J2130A

-

PICOTEST Corp.

J2130A - PICOTEST Corp.

When using the network analyzer to measure impedance, such as the capacitance and ESR or a capacitor, or the DCR of an inductor, etc., it is often necessary to provide a voltage bias to the device being tested. This is true of semiconductor junction capacitances, varactors, and some ceramic capacitors (especially X5R). In these cases the impedance is a function of the DC bias on the device. The Picotest DC bias injector (J2130A) is used for this purpose during impedance measurements.

Product

Elevated 1.68 (48.00) - 7.00 (198.00) High Performance Bias Ball Probe

POGO-1UN-7-S

-

ECT

POGO-1UN-7-S - ECT

Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02

Product

Test System

ITC57300

-

Integrated Technology Corp.

ITC57300 - Integrated Technology Corp.

The ITC57300 Dynamic Parametric Test System mainframe accepts Test Heads that perform nondestructive transient measurements on semiconductor devices such as Insulated Gate Bipolar Transistors (IGBT), power MOSFETs, diodes, and other bipolar devices(requires additional optional bias power supplies and custom personality boards). Included in the mainframe are all test equipment and software necessary to analyze and perform resistive and inductive switching time, switching losses, gate charge, Trr/Qrr, and other transient tests.

Product

Narrow Band Multiplier

-

Radiometer Physics GmbH

Radiometer Physics GmbH

*no mechanical tuners*fullband operation*planar design*bias voltage required