RS422
One of several standards that incorporate balanced line signals into DB connectors. A pair of wires is used to carry each signal. The data is encoded and decoded as a differential voltage between the two lines. (www.sangoma.com)
See Also: Serial Communications, I2C, RS232, RS485
-
Product
RS-422 RS-423 RS-485
-
The low-power, high-speed transceivers of this family are designed for RS-485, RS-422 and RS-423 communication applications. They usually contain one driver and one receiver in half duplex configuration. Each driver output and receiver input is protected against electrostatic discharge up to ± 15 kV and has no latch-up. These transceivers operate with a 5 V supply and draw a very low supply current when unloaded or fully loaded but with disabled drivers.
-
Product
RS-485/RS-422
-
Renesas' half duplex and full duplex RS-485/RS-422 transceivers are available in a variety of speed grades to address any application needing reliable data transmission over twisted pair wiring.
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-104
Serial Interface
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
RS-422/485 Repeater
ADAM-4510
-
Automatic RS-485 data flow controlSurge protection RS-485 data lineTransmission speed up to 115.2 KbpsNetworking up to 1200 meters (4000 feet)LED indicator to monitor status
-
Product
RS-232 to RS-422/RS-485 Converter
ND-6520
-
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
Signal Converters & Load Cell Signal Converter
-
Mantracourt provide a range of signal converter modules which take load cell or strain bridge inputs and provide a data output in a variety of bus and protocol formats. Hardware formats include RS232, RS422 RS485, CAN and USB. Signal converter protocols include Industry Standards such as MODBUS, or Mantracourt’s own proprietary protocols which have been optimised for either ease of use (MantraASCII2) or higher speed communications (MantraBus2).
-
Product
USB / RS232 / RS485 / RS422 Opto Isolators
-
USB has now moved from the desktop to more challenging environments, including instrumentation, point of sales, factory & building automation, etc. With our rugged, industrial-grade USB isolators and USB to RS232 / RS485 / RS422 optically-isolated converters, we ensure that your assets are well protected from unexpected events.
-
Product
GPIB-RS485, GPIB Instrument Control Device
779733-04
GPIB Controller
Serial, RS485/RS422 GPIB Instrument Control Device - The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 … serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488, RS485, and RS422 standards, as well as interpret and execute high-level commands from the serial port, including serial‑to‑GPIB, and GPIB‑to‑serial protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
RS-232 to RS-422/RS-485 Optically Isolated Interface Converter
Model 245
-
Total Isolation; Selectable RS-422 or RS-485; Selectable 2 or 4 wire RS-485; Intelligent Control of RS-485; TD & RD LED's on Each Side of Opto Barrier; Data Rates up to 128 KBPS. The Model 245 RS-232 to RS-422/RS-485 Optically Isolated Interface Converter is an optically isolated version of the Model 285.
-
Product
3U CPCI MIL1553B Board
MS 1726
-
*Bus Interface:- 32 Bit PCI Bus with 3 U Form factor*PCI to PCI Bridge Interface*Speed of operation up to 66MHz*1 1553B dual redundant channel*4 RS422 Channels*16 TTL I/O Channels*Message Storage Buffer*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
Product
Universal Pylon Tester
MS 1121
-
Portable test equipment to check the electrical functionalities of pylons by simulating various store types in aircraft. This system is able to simulate the functionalities of different PIBs (IB/MB/CF, OB & Laser). The system provides facility to test two Pylons in parallel. The tester provides aircraft specific AC &DC voltages and facility to inject discrete inputs for checking output(s) viz firing voltages, fusing voltages. The system provides four channels of RS422 and Two channels of 1553B communication. Portable unit with caster wheels with all required hardware, power supplies, instruments, connectors and laptop housed in it.
-
Product
µModule Isolated Transceivers
-
Analog Devices µModule (micromodule) isolated transceivers provide robust galvanic isolation for digital serial communication interfaces, including SPI, I2C, RS-485/RS-422, RS-232, and USB. Isolation barriers are implemented using Ethernet transformers, coupling capacitors, or embedded inductors. All devices are simple to configure, have very low EMI susceptibility and emissions, and feature high noise immunity to preserve signal integrity.
-
Product
4-Port RS-422/485 Isolated Serial Communications Card
cPCI-3544
Communications Module
- 32-bit CompactPCI®, PICMG® 2.0 Rev 2.1- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS- Four asynchronous communications ports with intelligent buffer- Four RS-422/485 ports- 2500 VRMS isolation voltage
-
Product
Modbus Data Concentrator and Gateway
MBDC-200
-
MBDC-200 is an autonomous Modbus data concentratorand collector. The MBDC-200 features two serial ports which can be configured as either RS-232 or RS-485 layer or by combining the two ports as a single RS-422 link. The data concentrator has also an Ethernet port and can be mounted on a DIN rail.
-
Product
USB-485/2, 2-Port, USB, RS485/RS422 Serial Interface Device
778476-02
Serial Interface
The USB‑485/2 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/2 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
ANSI X3.28 Interface Board
Model 4804B-7
-
* F30145 firmware converts printable ASCII character strings into the ANSI X3.28 serial protocol.* User selectable single-ended RS-232 and differential RS-422/RS-485 serial signals.* Can be used to replace obsolete ICS 4814 Interfaces.* Connect to the rear panel with a GPIB Flat-ribbon cable or with a GPIB Connector/Address Switch Cable.* Runs on 5 Vdc regulated or 5.5 to 15 V unregulated power.
-
Product
Multi Protocol Analyzer
LE-2500R
-
LE-3500R/LE-2500R adopted TTL port as its standard besides RS-232C, RS-422, and RS-485 while having the same feature such as small and light body of LE-3500/LE-2500. You can monitor I2C or SPI without expansion board.
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-44
Serial Interface
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
8-Port RS-422 Async Serial Communications Adapter PMC
2316
-
The Technobox 8-Port Async Communication adapter provides eight 16550-based UARTs using RS422 signaling levels
-
Product
Surface And Subsurface EW System Tester
MS 1119
-
CPCI Based BTA is used to test ECM System Processor (80386 & 8051) Boards. This system consists of a Single Board Computer (SBC), CPCI RS422 Communication and Bus Interface Board (CBI), CPCI Digital Input & Output (DIO) Board and CPCI Analog Input & Output (AIO) Board to provide the necessary input/output signals to/from the board to be tested.
-
Product
6U Compact PCI Multiport Serial Card
CP69002
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP69002 is designed as 6U Compact PCI Multiport Serial Card. The eight serial ports are in depended and magnetic isolated. The transform mode can be configured as RS232, RS422 and RS485 through the jumpers. The upstream interface is 32 bit 33MHz PCI bus.
-
Product
Protocol Converter
MACC
-
When designing or upgrading avionics systems we are often faced with the task of integrating components that were not originally designed to work together.A control computer that communicates using RS-232 may need to control component that expects MIL-STD-1553 messages or an INS may put out ARINC-429 labels, which are needed by Multi function Display designed around RS-422.Faced with problems like these, integrators must choose between two poor options. They must either give up on one of the units in favor of another unit that may be less suitable but uses the appropriate communications spec; or they must add a computer system – often PC104 – which can translate from one unit to the other. These computers are generally large, heavy, hot, and require substantial power.
-
Product
IP Pulse
-
IP Compatible card with 4 programmable pulse generators. TTL or RS422 / RS485 compatible outputs. Programmable pulse - nS to seconds. Programmable count or free
-
Product
Remote Data Concentrator
-
Remote Data Concentrators (RDC) process and format aircraft sensor data into a common digital format over MIL-STD-1553, RS-422 and ARINC-429 protocols, which can then be received by avionics computers and cockpit displays that require engine/aircraft sensor data in a digitized form.
-
Product
PCIe Fast Multifunction, Multichannel Counter Board, Optically Isolated, RS-422 Inputs
APCIE-1711
-
The APCIe-1711 board is a fast multifunction and multichannel counter board for the PCI Express bus. The strengths of this board are its wide range of applications and high precision and reliability for industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provide the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied software. The flexible programming facilities on this board allow many different user applications to be quickly and easily developed and reconfigured as further requirements arise.
-
Product
ARINC 818 Tester
Test Platform
iWave 3U VPX High-Speed Video/Data Processing Card is a rugged standalone module in the 3U VPX form factor, aimed for the high-speed data, video processing, and display applications is ideal for military, defense, and aerospace applications requiring an optimal balance of performance and power efficiency. iWave 3U VPX High-Speed Video/Data Processing Card is implemented using Xilinx Kintex-7 device architecture and has I/O interfaces including High speed 16 channels of transceiver interfaces capable of operating up to 6 Gbps data rate, Gigabit Ethernet, RS232, RS422, PCIe interface, Built-in health monitoring circuits, HDMI input, and output interfaces
-
Product
8-Port Non-Isolated RS-232/422/485 Ethernet Card
ECU-P1618D
-
enables 8 legacy serial devices to communicate over a standard LAN/Ethernet network. It supports multi-protocol operation (RS-232, RS-422, or RS-485) and acts as a gateway for data, often featuring virtual COM port redirection and high-speed data transfer.
-
Product
NI-6584, 16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
781290-01
Digital I/O Adapter
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter
-
Product
RS-485/RS-422 Fault Protected
-
Renesas' fault protected RS-485/RS-422 transceivers, also known as overvoltage protected transceivers (OVP), offer robust fault tolerance and high performance.
-
Product
3U CPCI ARINC 429 Board
MS 1725
-
- Bus Interface:- 32 Bit PCI Bus with 3 U Form factor- PCI to PCI Bridge Interface- Speed of operation up to 66MHz- 8 ARINC 429 TX and 16 ARINC 429 RX channels- 4 RS422 Channels- 16 TTL I/O Channels- Message Storage Buffer- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
