Stepping Motor
A device that translates electrical pulses into precise mechanical movement. The output shaft may deliver rotary or linear motion. (www.seanet.com)
See Also: Electric Motor, Servomotor
-
product
Manual Step Attenuator, DC to 4 GHz, 0 to 70 dB, 10 dB steps
8495A
The Keysight 8495A dc to 4 GHz manual step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 10 dB steps from 0 to 70 dB. Precision gold-plated leaf springs ensure long life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
product
Small Motor Dynamometer
90407
The Model 90407 Conveyor Test Stand by Sensor Developments Inc. is a device used for testing operational parameters of a conveyor motor/roller. The system operates the conveyor motor/roller and performs loading operations, while recording all of the important motor/roller parameters for later analysis.
-
product
Motorized Force Test System
MT Series
In the past, film extruders, paper producers, converters, and woven/non-woven fabric producers have had the choice of test stands and universal test machines which are either value-priced peak-force-only machines, or expensive computer-operated integral-load cell machines. Now you can have the best of both worlds in a single instrument. The series MT-1500, a simple to use computer operated tester, with Quality Control software for automatic calculation and graphical display of break, elongation, yield, modulus, and other, tension and compression force information.
-
product
Fully Automatic No Load ( Routine) Testing Panel For Self Priming Motors
Aarohi Embedded Systems Pvt. Ltd
Aarohi introduced fully automatic routine testing panel. The primary purpose of the routine test is to insure freedom from electrical and mechanical defects, and to demonstrate by means of key tests the similarity of the motor to a “standard” motor of the same design. this panel also help to enhance productivity, Work efficiency & reduces need for skill operator.
-
product
Electric Servo Motor Type 2 · 4 Poster Vibration Tester
It arranges four 3-axis vibration testers equipped with a high torque, ultra-low inertia servomotor to test the vibration of the finished vehicle.
-
product
Motor Vehicle Inspect Lines Engineer Program
Foshan Analytical Instrument Co, Ltd.
It is suitable for measurement of motor vehicles equipped ignition engine with max total mass more than 3500kg. Including the dual idle speed method test. Meet the requirement of GB18285-2005"Limits and Measurement Methods for Exhaust Pollutomts from Vehicles Equipped Igintion Eigine under Two-speed Idle conditions and simple Driving Mode Conditions". The system can select the prompt mode of the dirver mode or the prompt mode of lattice screen.
-
product
Multi-Channel Attenuation Control Unit (4-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7204B
The J7204B is a multi-channel (4-channels) attenuation solution for signal attenuation and conditioning of up to 4 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7204B reduces cost of ownership and provide the best measurement accuracy.
-
product
Modular Low Voltage Motor Protection
LM10
The GE Multilin LM10 Low Voltage Motor Protection System is a modular device for low voltage motor protection. The compact design of the LM10 is ideally suited for Low Voltage Motor Control Center applications but can also be used in standalone applications. The LM10 comes standard with the DeviceNet protocol that allows the user to control and monitor the relay over a network. The relay also has an interface port to communicate with the optional LM10 Programmable Display Unit (PDU).
-
product
Traction and Induction Motor Test Systems
Crest makes state-of-the art test systems for testing 3-phase AC motors used in traction and other industrial applications.
-
product
Motor Driver ICs
The ST product portfolio offers a wide range of motor control ICs, well-suited for the most demanding automotive environments, covering the requirements of brushed DC motors, stepper motors and brushless DC motors, over an extensive range of voltage and current ratings. Efficiency and accuracy of our motor drivers are guaranteed by a unique combination of low-loss PowerMOS output stages and advanced control circuitry. Robustness and reliability are provided by the integration of a comprehensive set of protection and diagnostic features.
-
product
Step Up Transformer
MagD
SCOPE proudly introduces Step-Up Transformer - MagD, specially designed to cater the needs of testing of instrument Transformers. Before new systems are put into service or after any occurrence of fault, the instrument transformers need to be tested for their outputs. It is to be ensured that these instrument transformers are giving proper outputs to the protective relays. MagD is used to plot excitation curves for instrument transformers. Inbuilt voltmeter and ammeter, eliminates the need of external meters for plotting of curves. It can also be used for de-magnetization of transformer cores and also turns-ratio tests can be conducted using MagD.
-
product
Motorized Test Stands
AMETEK Sensors, Test & Calibration
Our motorized test stands are optimized for production floor operation. They provide a constant test speed and require a force gauge to be integrated with the test stand.
-
product
Phase Sequence and Motor Rotation Tester
PRM-6
The PRM-6 Motor and Phase Rotation Tester can test the motor rotation of 3-phase systems, and verify 3-phase receptacle wiring and phase sequencing with test leads.
-
product
Multi-Channel Attenuation Control Unit (5-channels), DC to 6 GHz, 0 to 121 dB, 1 dB Step
J7205A
The J7205A is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to5 devices under test (DUT). Operating frequency from DC to 6 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205A reduces cost of ownership and provide the best measurement accuracy.
-
product
PXI Dual RF Attenuator 63dB in 1 dB steps
41-180-022
The 41-180 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module.
-
product
3 Phase/ Motor Rotation Tester
Phase rotation indication by both audio and indicator, checking if currents of three different rating are in proper phase. Phase open-circuit detection by indicator.
-
product
Fan Motor Tester
Shanghai Aoboor Electric Co., Ltd.
applicable for testing DC brushed and brushless motor fans.
-
product
Electric Motor Dynamometer
Dynamometer consists of aggressively designed rotor technology that allows for higher torque without the need for multiple rotors. Thus not only does the WB Series unit offer more pack to the punch, but the inertia of the WB Series unit stays well below the inertia of the engine being load-tested.
-
product
Attenuation Control Unit, DC to 18 GHz, 0 to 121 dB, 1-dB Steps
J7201B
Designed for WLAN and WiMAX™ device manufacturing test and mobile handset base transceiver station (BTS) handover test.
-
product
ASTRO BRUSHLESS MOTOR
4535
The purpose of the development of the 4535 was to deliver the same quality and reliability of our 32XX motors but at nearly 4x the power. Starting at the core of the motor, the 4535 uses the highest grade of sintered samarium-cobalt magnet. Unlike hobby grade neodymium magnets, these samarium-cobalt magnets are able to withstand high operating temperatures without losing magnetic strength or experiencing permanent demagnetization. Ultra-thin laminations are used in the stator to ensure minimal iron losses and maximize efficiency. All components of the motor are rated to at least 200°C to handle high continuous and burst power. Finally, to ensure manufacturing quality, all 4535 motors are designed and manufactured in Astro Flight's facility in Irvine, CA.
-
product
Wireless Current Quality Analyzer and Motor Analyzer - 3SIQ
Signals & Systems India Private Limited
3SIQ enables current quality analysis using wireless technology and thus allows operators to work from a safe distance. This Industry 4.0 and ISO 50001 Condition-based monitoring solution seamlessly combines the flexibility of using any Smart Phone or Tablet to provide powerful analytics and insights towards predictive maintenance, making the maintenance engineers’ life not just safer, but smarter as well.
-
product
Linear Vibration Motor Aging Unit
BK2019A
The BK2019A Linear Vibration Motor Aging Test System was designed to test your linear vibration motors for long term reliability. It can test 20 DUT’s at one time and you can stack them easily so you can test hundreds of DUT’s simultaneously in a small space. This is a great machine to ensure your product will do its job for it's expected life.
-
product
Programmable Step Attenuator, DC to 50 GHz, 0 to 65 dB, 5 dB steps
84908M
Keysight now offers a family of higher frequency attenuators for your communications and aerospace applications. Combining low insertion loss with long life and excellent repeatability, these attenuators safeguard your test platform from failures, recalibration, downtime, and lost production.
-
product
Multi Channel Linear Vibration Motor Current Isolation tester
BK2017
The BK2017 Current and Isolation Tester was designed as a single purpose machine for quickly testing up to 8 linear vibration motors at a time. You can test current and isolation without checking other characteristics of the motor. With its simple design, it is very easy to use and the results appear clearly on the screen in about half a second. And with only 2 cables to connect, it can quickly be plugged into an automatic loader/sorter for even faster results!
-
product
Step & Contact Meter
HT2055
HT2055 consists in a power unit and a voltmetric unit, necessary for carrying out step and contact voltage measurements in industrial electric installations (TN systems, transformer cabinets) with a rated test current up to 50A.
-
product
Static Electric Motor Analyzers
Baker Instruments’ static motor test equipment is the industry-leading suite of products for detecting weaknesses and faults in the insulation systems of electric motors, generators and coils. Employing both low-voltage and high-voltage tests – such as Baker’s signature surge test - these essential troubleshooting and predictive maintenance tools allow maintenance professionals to assess any need to maintain or replace specific motors and generators that support their business. Equally at home in the motor repair shop or on a plant floor, these testers ensure that the electrical condition of your rotating machinery is understood.
-
product
Motorized Constant Loader
CLE-150 Series
When we measure the hardness of rubber test specimen etc. with durometer, we have the possibility to make an error for the result of the measurement. To make solution for such an important factor fo the error, CLE-150 Series is employed the motor driving system for the descent speed control, and then we could realize to measure the hardness of constant speed and constant pressure that is precise and reproducible.
-
product
Two Phase AC Motor Drive
MS 2014
Excellent High Speed Response. With help of semiconductor high end motion control algorithm and advanced common gain concept, a high speed response is achieved, therefore satisfying all motion control needs. Built-in Accuracy Improvement Features. Drive include features to improve total positioning accuracy of the mechanical system.
-
product
Wiper Motor Tester
Shanghai Aoboor Electric Co., Ltd.
Applicable for testing the proformance of automotive wiper motors and assemblies
-
product
Electric Servo Motor Type Tension and Compression Tester
It is a tensile / compression fatigue / durability / performance tester for various materials and automotive parts that have an ultra low inertia AC servomotor mounted on the actuator.
