Showing results: 1006 - 1020 of 3941 items found.
-
TCi -
C-Therm Technologies Ltd.
The default C-Therm TCi Thermal Conductivity Analyzer employs the Modified Transient Plane Source (MTPS) technique in characterizing the thermal conductivity and effusivity of materials. It employs a one-sided, interfacial heat reflectance sensor that applies a momentary constant heat source to the sample. Typically, the measurement pulse is between 1 to 3 seconds. Thermal conductivity and effusivity are measured directly, providing a detailed overview of the heat transfer properties of the sample material.
-
EMGA-930 -
HORIBA, Ltd.
This is a simultaneous oxygen, nitrogen & hydrogen elemental analyzer with high accuracy and repeatability suiting to cutting-edge technology's R&D as well as quality control in the market of steel, new materials, catalyst and so on. This is a new generation model optimized to fit to user's requests.The oxygen is measured as carbon monoxide and carbon dioxide by two non-dispersive infrared detectors, the nitrogen by a thermal conductivity detector and the hydrogen with non dispersive Infra Red detector as H2O.
-
DTA-BERT -
ShinewayTech
DTA-BERT E1/Datacom Transmission Analyzer can perform E1 transmission performance test (BERT) and status monitoring on data link (V.35, V.24/RS232, RS449, RS530, X.21). Model T can also perform G.703-64K bit error test, PCM31/30 test and Jitter test. Featuring comprehensive functions, easy operation and compact design, DTA-BERT provides total solutions for E1 line analysis and maintenance.
-
PCA 400 -
Bacharach, Inc.
Bacharach’s PCA® 400 combustion & emissions analyzer offers everything you and your technicians need to commission, tune, maintain and certify any boiler. It is perfect for spot-checking and tuning your engines with the high-range CO sensor and available sample conditioner. Whether it’s boiler combustion or emissions testing of your natural gas, stationary genset or mobile fleet vehicles, monitoring your emissions is fast, easy and accurate.
-
EMIA-Pro -
HORIBA, Ltd.
The EMIA-Pro, Carbon/Sulfur Analyzer is based on HORIBA''s vast knowledge of Non-Dispersive Infrared (NDIR) technology and our wealth of experience acquired from our EMIA series. EMIA-Pro offers improved the cleaning efficiency, enhanced user-friendly software, durability, operability and maintenance to ensure efficient measurements and its shortened measurement cycle time accelerates repetitive measurements up to 200 times, thus improving development and manufacturing speed.
-
RT-Lube -
Micromem Inc.
Instrument platform that is capable of real time, on site detection of wear elements in lubricating fluids. Currently the process to test lubricants is to take a manual sample for lab testing. This approach is expensive, labor intensive and time consuming. The RT-Lube Analyzer can replace this manual approach by automatically sampling, on a pre-scheduled basis, the fluid under consideration. The analysis is immediate and is communicated back to cloud based storage systems where the analytics can take place.
-
CI-IN36 -
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
CI-IN36 adopts the sensor that is made of thin polymer film, which can test the dew point with good stability. It will not influenced by condensed water and most compounds. This analyzer has received automatic zero point calibration and gain return patents with wide measure range, high accuracy, good stability and high performance cost ratio. - See more at: http://en.ci-ele.com/470baa2f-f4d7-af3b-c88b-b26356a1660d/8e93bc9f-4658-e0c4-2205-0be00b504269.shtml#sthash.KzPqj2sw.dpuf
-
PB6800 -
Integrated Technology Corp.
The ITC line of Probilt, probe card analyzers provide fast, accurate and repeatable test data for all types of probe card technologies. Simple user definable vision parameters allow even the newest and most complex probe tip geometries to be captured and accurately measured. Probilt’s PB6800 large measurement chuck allows probe arrays as big as 300 mm in diameter to be touched down without overhanging the chuck surface.
-
FS2520 -
FuturePlus Systems
The FS2520 is our newest and fastest logic analyzer probe used to test DDR4 DIMM memory. It is designed to work exclusively with 3 Keysight U4164A logic analysis modules operating in either Quad Sample State or Quarter Channel 10GHz timing modes. This gives the user an extremely effective tool for debugging, testing and verifying DDR4 DIMMs running above 4000MT/s. It’s like having a 100 channel scope.
-
1160 -
The Eastern Specialty Company
Eliminate trips to a site with TESCO’s CAT. 1160 Signal Strength Analyzer. When a meter is not reporting reliably to the Head-end, or for a new meter, concentrator, or antenna installation, TESCO’s SSA will show you the best location for the equipment. Be certain that your antenna placement is in the best location. The SSA actually joins the network, locates and analyzes all the neighbors, and provides a visual indication of the relative signal strength, quality, and throughput of each of them.
-
FSA-100 -
ShinewayTech
ShinewayTech® FSA-100 series 6GHz spectrum analyzer are widely used in 2G/3G/4G/5G etc. FSA-100 series have the industry's rare high receiver sensitivity performance with a minimum display average noise level of -165dBm/Hz. Power measurement dynamic range up to 100dB, maximum RF input power exceeds 27dBm. FSA-100 series are equipped with a 7" ultra-large capacitive touch screen (resolution 1024*600). Excellent user experience.
-
SPECTRO Analytical Instruments GmbH
To meet the divergent needs of industry, SPECTRO offers two families of optical emission spectroscopy metal analyzers with arc and spark excitation (arc spark OES). Optical emission spectroscopy using arc and spark excitation (Arc Spark OES) is the preferred method for trace metal analysis to determine the chemical composition of metallic samples. This process is widely used in the metal making industries, including primary producers, foundries, die casters and manufacturing.
-
SafeTest 60 -
Seward Medical
The Rigel SafeTest 60 is a robust, reliable and dedicated medical safety analyzer. It is ideal for testing high volumes of medical and laboratory equipment that does not require patient lead testing, such as beds, hoists, infusion pumps, CPAP's and centrifuges etc. With a large colour display and a colour-coded user interface, it's easy to select the required tests with a single key press, whilst a fast step-through of the test routine makes the testing process speedy and dependable
-
LD-LOGA-A10 -
Labodam
Oil and Grease analyzerLD-LOGA-A10is a tabletop analyzer with a sample testing range of0.12 mg/L to 840 mg/L. The unit displays and prints the sample spectra, position and wavenumber of the absorption peak. It features self-contained optical and electrical system withhigh degree integration. Testing data and spectrograms can be saved to hard disk forchecking and printing anytime Sensor signal processing uses lock-in amplifier circuitimproving the analyzer’s SNR and the minimum detection limit.
-
HY-OPTIMA™ 700B Series -
H2scan Corp.
H2scan’s HY-OPTIMA™ 700B series in-line, real time hydrogen-specific process analyzers are designed for ease of use, interface flexibility and true process control. The HY-OPTIMA™ 700B series is a solid-state sensor that is configured to operate in process gas streams with temperatures up to 60ºC. The HY-OPTIMA™ 700B series is ideal for hydrogen production and petrochemical applications where real-time measurements can enhance process plant efficiencies, diagnostics and maintenance management.
