Showing results: 3706 - 3720 of 3938 items found.
-
ARC Technology Solutions
ARC has experience with complex, commercially available test executives that are available for high volume production needs. Often times, when you don’t need the horsepower of a full featured executive, you are left with creating a specifically defined test program or crafting your own test sequencer. Rather than go down this path and spending your time on architecture, TestCentre brings a simple, yet elegant solution to this all-common problem. Used in many of ARC’s standard test stations, the robust, sequence based architecture of TestCentre, allows you to focus on the testing task at hand. While having some of the more advanced features found in high-end test executives, TestCentre, when mixed with RF analyzers and PXI based test solutions are a great, low cost solution to help solve your everyday testing requirements. Along with TestCentre and an ARC supplied rack-based test platform, your test challenges can be solved in doing circuit card testing, assembly/module level testing, or depot repair troubleshooting tasks.
-
mks Ophir
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
VOIP Echo -
GL Communications Inc.
*The Voice Band Analyzer (VBA) is an analysis tool for monitoring the quality of voice band traffic (including hybrid echo) over VoIP, TDM and wireless networks*VBA works in conjunction with GL's TDM, Packet, and Wireless non-intrusive capture products, such as T1 and E1 Call Capture and Analysis, VoIP PacketScan&trade, and GSM, CDMA, and 3G Call Capture Products. VBA instantly detects voice file captures and with appropriately installed analysis modules, monitors speech levels, noise levels, and hybrid echo. Other analysis modules such as ITU-T P.561, P.562, P.563, fax and modem analysis, and many others can be hosted as plug-ins.*The VBA application can also operate on pre-captured files. It supports A-Law, µ-Law, 16-bit PCM (Intel), 16-bit PCM (Motorola) and MS Wave file formats.*Required software PKV100 and VBA032 at each probe location and PKV170 PacketScanWEB - Network Surveillance Software*Required hardware - 1U rack PC with sufficient hard disk for capturing over 10,000 calls (80 GB HD) for each VBA colocated with a probe*Additional hardware - PC for PKV100 PacketScan™ Software
-
RMO-TW Series -
IBEKO Power AB
RMO-TW series is perfect for winding resistance measurements of inductive objects. It is ideal for testing transformer windings (power transformers, distribution, autotransformers) and for on-load tap changer verification. In addition, any RMO-TW transformer ohmmeter & tap changer analyzer can also perform transformer demagnetization.The series contains 4 models, with maximal test currents from 10 A (RMO10TW) to 50 A (RMO50TW). They are fitted in a portable and lightweight metal housing.All transformer ohmmeters from RMO-TW series generate a true DC ripple-free current with automatically regulated measurement and discharging circuit. The injection of current and discharge of energy from the test object are automatically regulated.Three independent channels enable testing of three windings in series. Consequently, this enables measurements of winding resistance in every tap position of an on-load tap changer without discharging between the tests.DV-Win software enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test. Finally, a user can export all results in the form of a report.
-
ABB Ability -
ABB Ltd.
ABB Ability mobile gas leak detection system uses ABB’s patented Off-Axis Integrated Cavity Output Spectroscopy (OA-ICOS) technique which has a sensitivity and precision more than 3000 times greater than legacy methods. This enables identification of leaks several hundred feet away from the source. Current traditional leak detection technology is slow, laborious and costly. Operators walk on foot near the pipeline with hand-held sensors making paper-based reports.This is slow and can lead to dangerous leaks being missed or not identified in a timely manner. ABB’s Ability mobile gas leak detection system delivers a low cost per leak solution with low false positives. Reporting includes mapping of the leaks available via a mobile app and measurements as Cloud-based service. The system consists of ABB’s Methane/Ethane Analyzer, a GPS, a sonic anemometer and proprietary leak detection software that presents real-time geospatial maps of multiple gas concentrations in real time. The software’s sophisticated leak detection algorithm combines the system’s measurements of gas concentrations (CH4, C2H6), local coordinates (GPS) and local wind velocity (sonic anemometer) to estimate the location of the leak. Readings are stored in the device and can be transmitted in real-time to the cloud for centralized monitoring.
-
AIM GmbH
AIM’s Fibre Channel test, simulation and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with one dual core RISC processor per port, massive and scalable DDR3 memory and IRIG-B time encoder/decoder functions are standard. The new ultra high performance intelligent 4-lane PCIe 2.0 interface modules offer 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The dual core processor provides onboard processing and data transfer capabilities for the most demanding Fibre Channel applications including upper layer protocol support done on board level. Large and high data throughput DDR3 RAM is accessible for the onboard processor as is a high performance FPGA implementing the customized Fibre Channel interfaces enabling the board to analyze incoming and modify outgoing data in real time. Each module provides 2 Fibre Channel compliant full duplex ports, implementing the full link level services. SFP cages make it suitable for different media types as optical or electrical network technologies. Ports operate either in Traffic Simulator or Analyzer/Monitor mode with support for port related Frame Statistics. Sophisticated packet capturing mechanism and monitoring features are complimented with powerful triggering and filtering capabilities.
-
PC-114 -
Com-Power Corporation
Perform Radiated & Conducted EMI pre-compliance testing at your facility up to 1 GHz. Com-Power PC-114 EMI emissions test system is a ideal solution performing pre-compliance EMC testing from 9 kHz - 1 GHz.. It has essential equipment needed for radiated and conducted EMI emissions measurements. The system includes a spectrum analyzer, antennas, near field probes, a preamplifier, LISN and a non conductive antenna tripod. Pre-compliance testing in EMC is a commonly used term not easy to define. In general, it implies testing done prior to formal testing for legal compliance. Formal legal compliance is performed at a facility designed and equipped with test instrumentation that is fully compliant with the applicable EMC standards. Such facility and instrumentation is capital intensive and can be expensive even to rent and not easily available. Compliance testing is performed per exacting requirements of the Standards and other reference documents adhering to the test methods and last detail. In addition, the test facility may require to be accredited by an accreditation body such as NVLAP, A2LA. Often it is desirable to know prior to compliance testing at such facility, whether a product is close to compliance and also how close. Pre-compliance testing is specially useful for specifications such as FCC, Part 15, EN 55022 or EN 55011 (CISPR 22 or CISPR11). Pre-compliance testing usually means using the full compliance methods but making a few educated compromises in use of site or equipment to reduce costs and testing time. Here are some benefits of pre-compliance testing.
-
RMO-TD Series -
IBEKO Power AB
Using the most advanced switch-mode technology available today, the RMO-TD series is ideal for winding resistance measurements of inductive objects. Transformer resistance meters and tap changer analyzers are perfect for testing:transformer windings (power transformers, distribution, autotransformers),all types of tap changers,generators,electrical motors,high-current busbar joints,cable splices,and welding joints.In addition, transformer demagnetization can also be done with all RMO-TD instruments.The RMO-TD series contains 3 models, with maximal test currents from 25 A (RMO25TD) to 60 A (RMO60TD).The three independent voltage sense channels enable testing of three windings in series. This enables measurements of winding resistance in every tap position of an on-load tap changer without discharging between the tests.All RMO-TD transformer resistance meters have a built-in tap changer control unit. It enables remote control of on-load tap changer (OLTC) directly from the device. In order to make the most out of this feature, DV-Win software is included which can be programmed to do everything automatically – running winding resistance tests and changing OLTC tap positions.The DV-Win software also enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test.All results can be exported in the report format.
-
AIM GmbH
> ARINC818 is a specification which has become an Industry standard for the transmission of uncompressed digital video. This commercial standard uses Fibre Channel as a point-to-point communication link for low latency with the ARINC818 defining the packetized protocol for transmission of the digital video information. It is highly flexible and can be used for a variety of onboard display systems in both commercial and military applications. AIM’s ARINC818 cards use our field proven Common Core hardware design giving the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with one dual core RISC processor per port, massive DDR3 memory and IRIG-B time encoder/decoder functions are standard. The ARINC818 modules are available in PCIe formats.The new ultra high performance intelligent 4-lane PCIe 2.0 interface modules offer 2 ports with full function test, simulation, monitoring and analyzer functions for ARINC818 interfaces. The dual core processor provides onboard processing and data transfer capabilities for the most demanding applications including ARINC818 support done on board level. Large and high data throughput DDR3 RAM is accessible for the onboard processor as is a high performance FPGA implementing the customized ARINC818 Interfaces enabling the board to analyze incoming data in real time. Each module provides 2 ARINC818 compliant ports. SFP cages make it suitable for different media types as optical or electrical network technologies. Each module is delivered with a Board Support Package (BSP) containing the onboard driver software, a full Application Programming Interface (API) and detailed getting started and programming guides. Powerful PBA.pro databus test and analysis software is optionally available for all our ARINC818 cards.
-
AIM GmbH
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
IBEKO Power AB
Transformer turns ratio testers from TRT series are DV Power instruments mainly designed for the measurement of power transformer turns ratio. Also, they measure transformer excitation current and phase shift. Special tests, such as automatic vector group detection and magnetic balance, can be performed on three-phase transformers and three-phase autotransformers.All models, except TRT03 series, have a built-in true three-phase power source, which is necessary for testing turns ratio of transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.DV Power turns ratio testers can output various test voltages for different applications. From the extremely low test voltage of 1 V AC that enables turns ratio verification of the majority of current transformers, up to the highest test voltage of 500 V AC that provides the most accurate turns ratio testing of power transformers used in power generation and transmission. By using the external booster, test voltage increases up to 5 kV AC in order to successfully test capacitive voltage transformers.All DV Power turns ratio testers have a built-in tap changer control unit. Because of that, it is possible to control the on-load tap changer (OLTC) directly from the device. In order to make the most out of this feature, the instrument and included DV-Win software can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions, and saving results. This option significantly facilitates and shortens the turns ratio testing time.TRT turns ratio testers use the same set of cables as three-phase winding ohmmeter & tap changer analyzers from the TWA series. Consequently, it enables one-time cable setup for performing eight tests:turns ratioexcitation currentphase anglemagnetic balancevector group detectionwinding resistanceon-load tap changer DVtestand demagnetization.
-
CO-A -
Hiden Analytical Ltd.
Designed for gas analysis applications of syngas, biogas and catalysis studies where levels of CO are analysed by the CO-A in the presence of nitrogen, carbon dioxide, methane and other gas mixtures.
-
CFA -
Hanatek Instruments
By measuring the stiffness of the substrate and crease bending resistance the user can optimise cartons for faster running and packaging speeds. The instrument allows individual creases to be analysed identifying problem areas in packaging design or manufacture. Industry research indicates that the packaging speeds of pre-glued skillets is governed by the energy required to open creases. The Hanatek CFA is the first instrument to isolate and accurately measure this key parameter The instrument measures: Bending resistance, bending moment, board stiffness, crease recovery stiffness, crease folding force, crease opening force.
-
SNYPER Family -
Siretta Ltd
2G, 3G and 4G LTE cellular signal analyser range - including Spectrum 'livescan'. The SNYPER is a sophisticated yet easy to use range of cellular signal analyser comprising 2G and 3G versions with LTE family Now available.
-
AFJ Instruments
A click is defined as a disturbance exceeding the limit of continuous noise for not longer than 200ms, separated from a subsequent or preceding disturbance by at least 200ms.
