DC Sources
A highly repeatable and stable DC voltage and current source.
-
Product
OTP-Based Test System
Test System
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
Product
(Automatic Redundant Battery Selector With Source Control And Monitoring)
ARBS 2600
-
La Marche Manufacturing Company
Our product is designed with high powered diodes to select the higher voltage of the two isolated DC power sources. The ARBS selects power from the best available battery while isolating the alternate battery bank. The special heat sink diode assembly is manufactured to handle high output requirements with safety margin to spare.
-
Product
LED Power Driver ATS
8491
-
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series
-
Product
Impedance Analyzer, 20 Hz to 10/20/30/50/120 MHz
E4990A
Impedance Analyzer
The E4990A Impedance Analyzer has a frequency range of 20 Hz to 120 MHz. The E4990A provides an industry best 0.045% (typical) basic accuracy over a wide impedance range, with a 40 V built-in DC bias source. The equivalent circuit analysis function supports seven different multi-parameter models and helps you to simulate your own equivalent parameter values of components.
-
Product
Precision Multi-Channel DC Source PXI Card
GX1838 Series
PXI Card
The GX1838 is a multi-channel programmable DC Source providing multiple discrete outputs for avionics automotive, industrial testing and other ATE applications.
-
Product
Controllable, Programmable Linear DC Source With Load
LAB / SLR
-
*Linear laboratory power supply*Integrated electronic load*Automatic range selection*Linear regulated DC source with automatic range selection*Built-in electronic load*Short-term peak load operation 240 or 480 watts*Protection against short circuit, overload and overtemperature*Double current / double voltage through "autoranging"*Fast control times approx. 250µ
-
Product
Precision Current Sources
-
DC Precision Current Sources provides precise and very stable output currents from 3 A to 10,000 A. The 6623A-PCS Series provides the best uncertainties of any DC high current sources (i.e. < 5 ppm of precision and stability at 1000A). In addition this Series is modular and initial output currents can be expanded at any time.
-
Product
Controllable, Programmable DC Source
LAB SMP
-
*Easiest operation via the front panel*Indication via graphic display*Constant current, voltage, resistance, power operation and simulation of PV characteristics*Creation of any voltage and current curves via memory card or digital interface (sequential control)*Voltage and current rise time (U and I slope) adjustable*Umax and Imax can be set by the user in order to limit the output voltage or current
-
Product
Power Electronics Test Solutions
-
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
Product
PSD Signal Processing Tool
SEEPOS
-
For most position measurement applications the SiTek SEEPOS system offers a complete and easy-to-use solution. High speed PSD electronics combined with digital signal processing and high speed USB data transfer gives a powerful measurement system. With its large dynamic range it can handle light powers from nW to mW from DC light sources as well as modulated light sources. All parameters, such as PSD bias voltage, amplifier gain, the use of analog and digital filters etc., are easily controlled from the included software and light spot position is continuously displayed both in XY and X-t, Y-t graphs. Optimized plot algorithms ensure that all data is visually seen on the screen even in full speed measurements. Included tools for data analysis and visualization simplify rapid scan through large data sets in order to find specific parts of interest.
-
Product
Portable AC/DC Power Supply
UPS S3
-
The Vanguard UPS S3 is an AC/DC adjustable output power supply designed to operate substation circuit breakers. The UPS S3’s AC and DC voltage sources can supply up to 10 Amperes during the circuit breaker coil energization and circuit breaker charging motor operation. Powered by a single phase 90-120 Vac voltage source, the UPS S3 provides an isolated adjustable AC/DC voltage source. Output voltages are variable via the front panel control knob.
-
Product
Mobile Comm DC Source w/ Battery Emulation
66321B
Battery Simulator
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66321B mobile communications dc source provides fast transient response, exceptional sourcing, output resistance programming, and precision measurement. This product is specially designed for testing next generation digital wireless communications products. The 66321B mobile communications dc source offers a new capability that simulates the internal resistance of a battery or battery pack. Additionally, these high performance models offer improved transient response and stable output operation with either short or long load leads.
-
Product
DC Power Source Systems
-
Looking for a proven, precise DC power source? Advanced Energy offers standard DC and pulsed-DC power-delivery options. Thanks to vast feature sets and reliable performance, our DC power generators are used in nearly every manufacturing market — semiconductor, flat panel, glass, thin film, etc. And via our global, dedicated support staff, we make sure you get the right DC power product for your processes and applications.
-
Product
Precision DC Source Instrumentation
-
High power, dual channel PXI User Power Supplies as well as precision DC source instrumentation. These products are offered in both PXI and GTXI formats.
-
Product
AC to DC Programmable Power Sources
-
CEHCO can supply AC to DC Programmable Power Sources. We offer standard or customized solutions. The ADG-L Series is up to 1000 VDC maximum output. ADG-P Series is up to 2000 VDC maximum output.
-
Product
Standards Source Instrumentation
-
PXI Arbitrary Waveform and Programmable Function Generators as well as DC source cards and a precision standards module.
-
Product
ENA Vector Network Analyzer
E5061B
Vector Network Analyzer
Select the best configuration for your test needs from a wide variety of test set options: 100 kHz to 1.5 GHz/ 3 GHz, 2-port, 50 or 75 ohm, transmission/reflection or S-parameter test set Address a broad range of applications with the LF-RF option (Option 3L5/3L4/3L3): 5 Hz to 3 GHz, 2-port, 50 ohm, S-parameter test set, gain-phase test port, built-in DC bias source Combine network analysis and impedance analysis to customize your application in a single instrument (Option3L5/3L4/3L3 plus 005) Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Multiple Output Bidirectional PSU
LAB-MOBI
-
Electronic Test & Power Systems
The LAB-MOBI is a series of multi channel High Power Bidirectional PSUs. Each system is able to operate as either a DC Source or a DC Electronic Load. This integrated approach features high dynamics enabling the user to switch seamlessly between quadrants. When sinking energy from the unit under test the LAB-MOBI automatically inverts the DC to AC and synchronises this output to the grid. Dedicated application modes are available for battery cycling and emulation, which can be used to implement specific test routines. Other common applications the LAB-MOBI is used for include testing electric motors, fuel cells, super capacitors and solar panels. Max. Volt. Output 1000V,Min. Power 60kW, Max. Power 500kW.
-
Product
Three-Phase Relay Test Equipment
AK-30
-
AC voltage source with 4 channels, current source and aux with 6 channels. DC source can be used simultaneously. Amplitude, frequency and phase angle can be adjusted respectively, independently and continuously; Control via PC via Ethernet RJ45 interface
-
Product
Phase Noise Analyzers
-
The phase noise analyzer portfolio from Rohde & Schwarz offers an affordable, mid-range solution with high sensitivity and fast measurements as well as high-end ultra-high-sensitivity solutions with advanced measurements modes. Ideal for phase noise analysis and VCO tests, the industry-leading solutions enable two-path phase noise analysis with real-time cross correlation and fast VCO characterization with built-in low-noise DC sources. Additionally, high-end signal and spectrum analysis can be added into a single box.
-
Product
Dual Mobile Comm DC Source w/ Battery Emulation, DVM
66319D
DC Power Supply
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.
-
Product
20-Channel SPST Power Switch Card
1260-120
Switch Card
Each channel of the 1260-120 can switch up to 13A, 250VAC or 10A, 125VDC; its switching capability makes it the ideal solution for applications requiring high-current switching of AC power, DC power supplies, and AC or DC current sources.
-
Product
Bridge Trainer
-
Salicon Bridge Trainer to measure unknown Resistance/Capacitance by balancing two legs of a Bridge Circuit. With the of DC Source, Student can set the null point by using different combinations of variable Resistors Circuit Diagram is provided on-board for Teaching/Training.
-
Product
Impedance Analyzers
-
The E4990A Impedance Analyzer with a frequency range of 20 Hz to 120 MHz provides an industry best 0.045% (typ.) basic accuracy over a wide impedance range, with a 40 V built-in DC bias source.
-
Product
Programmable DC Current Source
Model 121
-
The Model 121 programmable DC current source is a precision instrument suitable for bench-top use or panel-mounted operation in labs, test facilities, and manufacturing environments. It provides a low-noise, highly stable source of current up to 100 mA, with convenient manual selection through 13 pre-set output levels, each representing a ten-fold change in power when attached to a resistive load. A “user” setting allows the current output to be defined anywhere within the operating range of the unit, from 100 nA to 100 mA.
-
Product
Precision I/V Source
MeasureReady™ 155
-
The MeasureReady™ 155 Precision I/V source combines premium performance with unprecedented simplicity for materials scientists and engineers requiring a precise source of current and voltage. Low RMS noise: from 200 nV (10 mV)/7 pA (1 µA). Bipolar, 4-quadrant power source. DC and AC modes supported up to 100 kHz*. Full scale ranges from 10 mV to 100 V (1 μA to 100 mA). 0.001% programming resolution (from 100 nV/10 pA.
-
Product
32 Channel Optically Isolated Digital Card
104-IDIO-16 Family
-
The Model 104-IDIO-16 is a 32-channel PC/104 utility board featuring 16 optically isolated inputs and 16 optically isolated solid state outputs. The isolated, non polarized inputs may be driven by either DC sources of 3-31V (or higher by special order) or AC sources at frequencies of 40Hz to 10KHz. Optically isolating the digital inputs from each other, and from the computer, assures smooth, error-free data transmission in noisy, real-world environments. The 16 input channels are available via a 34-pin IDC type header. The fully protected solid state outputs, capable of sourcing 2A each, are inherently more reliable than electromechanical relays and give system architects a more robust product to design with. The solid state outputs are available via a 50 pin IDC type header.
-
Product
16CH Battery Cell Simulator
Chroma 87001
-
Chroma Systems Solutions, Inc.
Chroma 87001 Battery Cell Simulator is a high precision, programmable, and bidirectional DC power source with both voltage source and current source functions. In addition, the model can be used as a multi-channel DC power supply or an electronic load as well. A single simulator has 16 channels and each of them can set voltage and current respectively via Chroma software.
-
Product
Tunable Laser Source, High Power And Lowest SSE, Top Line
N7776C
Laser Source
The new Keysight N7776C top line tunable laser source is designed to reach best-in-class accuracy in static and swept operation for outstanding test efficiency. Two-way sweeps up to 200 nm/s speed with sub-picometer repeatability and without impacting the specified dynamic accuracy accelerate wavelength-dependent alignment processes and the automated calibration of wavelength-selective devices. Shorter time to testing and faster swept-wavelength tests help reduce test cost per device, improve test margins and lower the cost of ownership.
-
Product
Optical Switches
Optical Source
Fast and reliable optical switches to streamline your test procedures. Can be customized with a wide range of switch configurations, fiber types and connectors.
