Conversion
-
product
Programmable Oscillator Amplifier
Computer Conversions Corporation
The Computer Conversions Corporation POA90-3 is a programmable quadrature oscillator with a built-in power amplifier, capable of driving current loads of up to 200mA. The sinusoidal outputs are 2.5Vrms signals that are phased 90° apart as REF out and REF out +90 (Quadrature), allowing the unit to be used with Synchro, Resolver, LVDT/RVDT, Inductosyn, or similar inductive transducers.
-
product
Mezzanine System
5158
The 5158 Electrical Conversion Module (ECM) provides eight (8) RS-232 outputs and eight (8) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
product
USB to RS-422/RS-485 Converter
ND-6530
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
GPIB-RS485/RS422 GPIB Instrument Control Device - Brazil 127-220VAC
779733-12
The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488, RS485, and RS422 standards, as well as interpret and execute high-level commands from the serial port, including serial‑to‑GPIB, and GPIB‑to‑serial protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
RS-232 to EIA-530 Interface Converter
Model 62-1 / 62-2
FEATURES: Supports 10 Category I & 3 Category II Circuits; Full EIA-530 & RS-422 Compliance; DTE & DCE Models; Meets MIL-STD-188-114 Type 1/2; Up to 256 KBPS Data Rate. Conversion between RS-232 and EIA-530 is accomplished by the Models 62-1 and 62-2. These devices provide conversion for the entire EIA-530 interface which includes ten Category I circuits and three Category II circuits.
-
product
Board Cameras
e-CAM & See3CAM Series of Camera Boards. e-CAM camera board is e-con's reference design featuring a board camera interfaced to a processor on its high speed CMOS interface. Board cameras are available for Jetson Developer kits and NXP i.MX6 boards. For processors, that don't have the Camera ISP pipeline, e-con Systems provides the complete software stack for raw image sensors. The software stack has a wide variety of features ranging from color correction, gamma correction, dead pixel correction, color space conversion, sharpen filter etc.
-
product
GigE And 3x ASI Ports For PCIe
DTA-2160
DekTec's Gigabit Ethernet adapter with three ASI/SDI ports, allowing zero-jitter transmission and reception of Transport Streams over IP networks; the additional three ASI ports allow easy conversion between the two interface types.
-
product
Resolver Systems and Resolver Sub Systems
TDSM
Computer Conversions Corporation
The TDSM Series are low cost absolute encoders consisting of a size 11 electromagnetic transducer and a 2.6 x 3.1 x .6 conversion module. The outputs available are 12 to 16 bit binary format representing 0 to 359.99 degrees of absolute shaft angle input. The transducer reference supply is also included in the module which is designed for printed circuit mounting. A data transfer and data hold line are provided for simple computer or microprocessor interfacing. These features in addition to the latest digital circuitry techniques, make these encoders the best selection in today's applications where resolutions greater than 10 bits are required with ultra high reliability assured.
-
product
Portable Hand Held Load Cell Indicator
MODEL SSI
The SSI is a Plug & Play Smart TEDS IEEE 1451.4 compliant portable handheld Load Cell Indicator. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SSI will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SSI can be set up by simple front panel push buttons. The SSI can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, inch pounds, etc. The SSI also has a Units key for automatic conversion of readings for load, torque and pressure. The SSI has an ultra-fast signal-sampling rate of 15,360 samples/second for true peak and/or valley testing capability. Auto-tare allows the meter to be set to zero for any input signal level. The SSI also features a USB port for data logging to a PC. You can also log data to the SSI’s internal memory storing up to 16,000 time and date stamped readings. The SSI also features 2 built-in solid-state alarm relays with LED and audible indicators. The SSI will operate up to 65 hours on a single charge or use the included battery charger for applications where the SSI is mounted permanently.
-
product
Battery Chargers
Electronic Test & Power Systems
Our dedicated range of battery chargers support Ni-Cd, Ni-MH, Li-ion and lead acid chemistries. Industrial lead acid battery chargers with temperature compensation are available at a variety of voltage levels and output powers. The high conversion efficiencies result in a small case style making the BC-SMPS product family ideal for system integration.
-
product
RF Converters
Typically designed for radar or wideband EMC test applications, our frequency converter modules are designed for the conversion between complex baseband waveforms and higher transmitted frequencies. These modules are ideal for integration with digitising modules.
-
product
LVDT I/O Cards
CPE4000
Computer Conversions Corporation
Computer Conversions’ CPe4000 Series are CompactPCI-Express (cPCIe) and PXI Express (PXIe) compliant: Synchro, Resolver, and LVDT/RVDT I/O Cards (predominantly output cards), with GEN1 and GEN 2 PCI Express interface, designed for accurate and reliable commercial, industrial and COTS-Mil. applications in test, simulation, motion control and shipboard data distribution. The CPe4000 Series drive up to 4 channels of Synchro, Resolver, 3-wire LVDT/RVDT outputs, or up to 8 channels of 2 wire LVDT/RVDT AC Sensor output sets.
-
product
Modular Real Time Video and Audio Processing
Synapse
Synapse is the industry’s most powerful and comprehensive audio and video processing system. Synapse modules make it possible to process, distribute, convert or analyse any type of uncompressed video and audio signal. Some examples: frame synchronization, video up & down conversion, audio (de)embedding, Dolby processing, integrity checking, logo insertion, multiviewing, etc.
-
product
Demodulator
LVDT-9312
LVDT 9312 is a compact, reliable and highly versatile LVDT/RVDT conversion module.
-
product
Precision Voltage to Current Converter
64-VCC
The 64-VCC precisely converts voltage to current. The unit can be placed in-line with a data acquisition system to achieve outstanding conversion accuracy for precise movements in valves or motors. The unit includes a unique current feedback measurement output to precisely monitor actual current in critical applications.
-
product
Current Mirrors
Analog Devices current mirrors are precision, high dynamic range, wide variable supply parts used for optical power monitoring, voltage biasing with current monitoring, and voltage-to-current conversion. Our current mirrors can monitor current down to as little as 3 nA and as much as 3 mA, with a linearity of 1% or better. The current dynamic range is 120 dB or 6 decades of current range, while the overcurrent protection feature in our devices forces the input pin to ground to avoid part damage. Over temperature (–40°C to +85°C) and process, the dynamic range only suffers 10 dB at the lower end of the range.
-
product
16 Channel Dual Range Multievent QDC
V965
The Mod. V965 is a 1-unit wide VME 6U module housing 16 Charge-to-Digital Conversion channels with current integrating negative inputs (50 Ohm impedance). For each channel, the input charge is converted to a voltage level by a QAC (Charge to Amplitude Conversion) section.
-
product
Bidirectional DC Power Supply + Regenerative Load
62000D
Chroma Systems Solutions, Inc.
Chroma 62000D programmable bidirectional DC power supplies have both power source and load characteristics, two quadrant operation, and allows feedback of the power from the DUT. They can be used for testing renewable energy power systems including PV/storage hybrid inverters, power conversion system (PCS) on charging/discharging, and as a battery simulator. The 62000D also is a fit for testing power components used in electric vehicles, such as bidirectional on-board chargers (BOBC), bidirectional DC convertors, and DC-AC motor drivers, and power conversion simulation tests of batteries in both directions.
-
product
32 Channel Multievent QDC
V792
The Mod. V792 is a 1-unit wide VME 6U module housing 32 Charge-to-Digital Conversion channels with current integrating negative inputs (50 Ohm impedance).For each channel, the input charge is converted to a voltage level by a QAC (Charge to Amplitude Conversion) section. Input range is 0 ÷ 400 pC.
-
product
BCD to Binary Converter
BCD250
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
product
Scalar Mixer / Converter Measurements
S95082B
The S95082B scalar mixer / converter measurements software provides an intuitive and easy-to-use user interface for setting up mixer and converter measurements with single or dual conversion stages. It controls the analyzer’s built-in source(s) and external signal generators for use as LO signals.
-
product
Ethernet To Modbus RTU Interfaces
ICS's Ethernet to Modbus Interfaces provide Modbus TCP/IP to Modbus RTU serial conversion and Raw Socket (Telnet) to control Modbus RTU Slave Devices. Available in small Minibox™ and OEM board formats. OEM board has Ethernet, GPIB and USB interface ports. All Interfaces include the VXI-11 protocol for use with: LINUX, UNIX, SunOS, Apple OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems.
-
product
AC / DC Transmitter
Knick Elektronische Messgeräte GmbH & Co. KG.
For the separation and conversion of sinusoidal and non-sinusoidal alternating currents and voltages into standard signals. TRMS Education / True-RMS. Calibrated switchable versions with Weitbereichsnetzeil and high working voltage up to 3600 V AC / DC.
-
product
Image Analysis & Stage Micrometers
The APPLIED IMAGE series of Image Analysis and Stage micrometers are ideally suited for calibrating optical, imaging, video, and reticle-based measurement systems. Designed for ease of use and manufactured for durability, the SM Series has both English and Metric scales in one or two axis configurations. Both types of micrometers come with NIST traceable calibration standards and are available on multiples substrates to perfectly fit your needs. The experience APPLIED IMAGE has in manufacturing precision imaged optical components makes us the trusted source for standards for magnification system microscopy and vision applications. Should you need to alter feature patterns, size, or substrate, fill out our Custom Optical Components and Standards form to start the conversation.
-
product
14 Bit 4-Kanal Arbitrary Waveform Generator Mit 4 X 600MS/s Od. 2 X 1,2GS/s
PXDAC4800
The PXDAC4800 is an exceptionally high-speed four channel Digital to Analog Conversion (DAC) board which may be used as an Arbitrary Waveform Generator, a waveform playback device, or for generating multiple communication frequency bands. Each DAC can output data at a maximum real rate of 1.2 GSPS at 14-bit for two channels or at 8-bit for four channels, or 600 MSPS at 14-bit for four channels. Each output signal has a bandwidth of up to 400 MHz for AC-Coupled configuration or up to 590 MHz for DC-Coupled configuration. Output waveforms may be “per-trigger” or “continuously looped” from the on-board 1 Gigabyte memory.
-
product
Schottky Barrier Bridge Quads
SemiGen’s Silicon Schottky Diodes are designed for applications through 40Ghz. The special process technology utilizes various metal schemes to provide excellent performance of Low, Medium, and High Barrier applications. The end result is a low resistance diode with tightly controlled capacitance which allows for optimum performance. Low conversation loss and superior TSS make these diodes ideal for detector / mixer applications with frequency ranges from S band to Ka band as well as modulators, lower power limiters and high speed switches.
-
product
Flexible Pick & Place Machine W/ 64-feeder Capacity
MC400
The MC400 Pick and Place machine places an enormous range of components, quickly and accurately, from 0201s through 100 x 150 mm SMDs, including BGAs, MBGAs, CSPs, µBGAs, MLFs, flip chips, odd form components and ultra-fine-pitch parts down to 15 mil. The system is easy to program and operate and comes standard with universal CAD conversion and teach-in capability.
-
product
16 Channel Multievent QDC
V792N
The Model V792N is a 1-unit wide VME 6U module housing 16 Charge-to-Digital Conversion channels with current integrating negative inputs (50 Ohm impedance). For each channel, the input charge is converted to a voltage level by a QAC (Charge to Amplitude Conversion) section. Input range is 0 ÷ 400 pC. The Model V792N features LEMO 00 connectors for both input and control signals. The outputs of the QAC sections are multiplexed and subsequently converted by two fast 12-bit ADCs.
-
product
Schottky Diodes
SemiGen’s Silicon Schottky Diodes are designed for applications through 40Ghz. The special process technology utilizes various metal schemes to provide excellent performance of Low, Medium, and High Barrier applications. The end result is a low resistance diode with tightly controlled capacitance which allows for optimum performance. Low conversation loss and superior TSS make these diodes ideal for detector / mixer applications with frequency ranges from S band to Ka band as well as modulators, lower power limiters and high speed switches.
-
product
Binary BCD Converters
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.





























