Conversion
-
product
Weather Radar Receiver
This is an example of a custom four-channel C-Band Receiver uses a single conversion technique to translate incoming 5.56 GHz radar signals to a 60 MHz IF. The Receiver is divided into two polarization sections, each with a dedicated channel for the received signal and a second channel for a reference signal originatingfrom the transmitter. There are two identical circuits in the Receiver, one reserved for vertically polarized signals, and the second for horizontal signals.
-
product
Laser Distance Meter for 40m With 10 Memories and Min. Measurement
MS-LDM340
*Measuring distance: 0.05 to 40m*Accuracy: ±1.5mm (±0.06in)*Unit conversion: mm/in/ft*Laser classification: Class 2*Laser type: 635nm <1mW*Dynamic measurement*Area, volume measurement*Pythagorean proposition measurement
-
product
Film Frame Test Handler
4170-IH
High throughput ・High withstand load, and high thrust table ・Expansion of the strip attachment area ：260(L) X 300(W) [Withinφ300mm for WLCSP]・LOT control by barcode/2D code reader ・Easy device type exchange only test socket and display screen setting・Auto-cleaning function unit is installed to clean the socket at any desired timing.・8/12 inches ring conversion ・S2/S8 regulation compliance・SEMI G85 compliance・SECS/GEM compliance
-
product
Transducers
A device that enables conversion between two different forms of energy thanks to its inherent properties.
-
product
Triaxal Seismograph
BC 1313 TRIAXIAL SEISMOGRAPH
BC 1313 seismographs are seismic accelerometers, the parameter measured – vibration acceleration. For BC 1313 seismic transducers, the system is provided for sensing element electrical stimulation using an actuator to determine conversion ratio true value during periodic recalibration without dismantling. Power check system is also allowed for in BC 1313 seismographs.
-
product
ANSI X3.28 to Modbus RTU Converter
Model 2399
* Converts ANSI X3.28 commandslinto Modbus RTU packets.* New 32 Address Mode supports multi-channel Modbus Controllers like the Watlow MLS300.* Control Modbus RTU devices from any ASCII serial source.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes serial baud rate conversion.* Internal logic is IEEE-488.2 compatible and uses SCPI commands for configurtion setup.* 2399 mounts on a DIN rail or on any flat panel.* Inexpensive way to maintain manufacturing equipment such as semiconductor fusion chambers, etc as the ANSI Controllers become obsolete.* Application Note AB23-3 describes how to use the 2399 to replace obsolete Watlow Controllers in the Axcelis/Fusion Gemini Asher.* 2399 Serial Keyboard Program lets you control and setup the 2399 and test the ANSI modes.* 239x Table Loader Program uploads ANSI Command Table entries from an Excel csv file.
-
product
Sound Level Monitor
McLennan Sound Monitoring, Inc
McLennan Sound Monitoring, Inc. offers two unique single-ranged instruments. For high sensitivity areas 41dBA – 101dBA range, and a standard range of 61dBA – 121dBA. A whisper from two feet will activate the 41dBA LED. Normal human conversation ranges from 60 – 80 dBA. Low level talk from two feet will activate the 61dBA LED.
-
product
Analog Input Module
PMC341
These modules have sixteen analog inputs which are sampled as two eight-channel banks. Eight A/D converters (ADCs) permit simultaneous conversion of all eight channels in a bank. All 16 channels share two generous 512-sample memory buffers. Conversion of each bank requires only 8µS, and all 16 channels can be sampled in just 16µs.
-
product
16 Channel Multievent QDC
V792N
The Model V792N is a 1-unit wide VME 6U module housing 16 Charge-to-Digital Conversion channels with current integrating negative inputs (50 Ohm impedance). For each channel, the input charge is converted to a voltage level by a QAC (Charge to Amplitude Conversion) section. Input range is 0 ÷ 400 pC. The Model V792N features LEMO 00 connectors for both input and control signals. The outputs of the QAC sections are multiplexed and subsequently converted by two fast 12-bit ADCs.
-
product
Analog Input Module
IP340
These modules have sixteen analog inputs which are sampled as two eight-channel banks. Eight A/D converters (ADCs) permit simultaneous conversion of all eight channels in a bank. A FIFO buffer holds the first bank’s data while the second bank is converted. Conversion of each bank requires only 8µS, and all 16 channels can be sampled in just 16µs.
-
product
Antenna, Loop Sensor
EM-6873 | 20 Hz – 100 KHz
The EM-6873 Loop Sensor Antenna uses passive circuits to transform magnetic field components between 20 Hz – 100 kHz to an equivalent open circuit two-terminal voltage on the receiving instrument. Use of the conversion Factor Chart, supplied with each antenna, will yield the strength of the magnetic induction field referenced to a uniform field. The loop is electrostatically shielded and therefore is sensitive only to the magnetic component (B-field) of the electromagnetic fields.
-
product
DC Filter Inductors
Osborne DC filter inductors (aka filter chokes) are commonly used in AC to DC conversion circuits to present an inductive voltage drop to the AC component of rectified current. This inductive voltage drop acts as a filter. Osborne designs filter inductors to components to function effectively (without saturation) in the presence of the DC current. Osborne will work with you to mitigate the impact of ripple frequency in conversion circuits. Every Osborne DC filter choke is designed for high performance with special consideration given to your circuit´s power supply frequency and conversion configuration.
-
product
1KVA to 3 KVA MIL Grade UPS Systems
ATUT-MIL Series
- Rack Mount True Online UPS- Rugged Military Grade Specs and Construction- Rugged Custom-built True Online UPS- Double Conversion Frequency Converters- Military Grade Battery Racks for SMF or LiFePO4 energy storage
-
product
Shunt Assembly
RSA-8
The RSA-8 Recording Shunt Assembly contains 8 individual shunts with terminal block programming for either a current channel (using the shunt) or bypassing the shunt and using a dropping resistor for conversion to a voltage channel.
-
product
Bi-Directional Differential-TTL I/O PXI Card
GX5642
The GX5642 is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), Functional Test, and factory automation applications. The GX5642 consists of 64 bi-directional TTL-to-differential LVDS I/O channels. Each channel has two ports (TTL and LVDS) and can be individually set to operate in either conversion or static I/O modes.
-
product
Vector And Scalar Mixer/Converter Measurements
S97083B
S97083B provides fully calibrated conversion gain/loss, relative phase, and absolute group delay measurements of mixers and converters without the need for reference or calibration mixers
-
product
mAEStro Audio Analog to Digital Converter
The mAEStro AADC-100 accepts balanced stereo analog audio inputs and converts them into a single digital bit stream in compliance with the AES/EBU (AES3) and S/PDIF digital audio standards. It generates 24-bit values and uses 128 times over-sampling for extremely accurate and linear analog to digital conversion, as well as offering a high dynamic range with exceptionally low total harmonic distortion and noise.
-
product
COTS Power Supplies
Advanced Conversion Technology, Inc
If you're searching for commercial off-the-shelf power supplies for your business and need military capability, contact Advanced Conversion Technology (ACT) immediately. ACT has a versatile line of power supplies designed with your needs in mind. We've developed a portfolio of COTS products based on our 35 years of satisfying military power conversion solutions in a variety of sea, air, and land applications. ACT's COTS ruggedized power supplies are for military and industrial use
-
product
16 SE Or 8 Diff. Input Channels, 8 Analog Current Output Channels, PCI Express
APCIE-3121-16-8C
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
Programmable AC Power Source
LSX Series
The LSX Series consists of a range of fully featured, single and three phase AC Power Sources. Available models range from 1.5kVA to 6kVA with an advanced programmable controller sporting a color touch screen user interface. Cost effective and fully programmable for both basic frequency conversion as well as advanced AC power line disturbance test and ATE applications. For applications not requiring advanced features, a basic function set M version of the LSX is available as well.Note: The LMX Series is not CE marked yet at this time.
-
product
Isolated A/D Converters
As the world’s leading supplier of data converters, Analog Devices is constantly introducing new A/D converters (ADCs) that drive system architectures. In the motor control arena, ADI’s converters solve the challenges associated with current and voltage monitoring, optical encoder feedback, and resolver-to-digital conversion. The introduction of the isolated ADC with its 3.75 kV standoff voltage is one example of ADI’s breakthroughs in performance and integration to ease the burden of design.
-
product
RS-232 to RS-422/RS-485 Converter
ND-6520
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
32 Channel Multievent QDC
V792
The Mod. V792 is a 1-unit wide VME 6U module housing 32 Charge-to-Digital Conversion channels with current integrating negative inputs (50 Ohm impedance).For each channel, the input charge is converted to a voltage level by a QAC (Charge to Amplitude Conversion) section. Input range is 0 ÷ 400 pC.
-
product
Mezzanine System Carrier
MMS6245
The MMS6245 gives you the ultimate flexibility in rugged embedded I/O by allowing you to customize the 64 user-configurable front panel signals with our patented Electrical Conversion Module (ECM) technology. This configurable XMC carrier can host up to four ECMs giving you the ability to customize I/O to your specific needs.
-
product
Brushless Resolver Transducer
HRB
Computer Conversions Corporation
Computer Conversions HRB90 has a shaft that meets CAM switch standards with a high shaft load capacity. They provide direct use on overhung loads and are ideal for use with sprockets. They withstand step stool abuse, they're small in size, easy to mount, waterproof & mill duty.
-
product
60 V Common Mode Differential Probes
The 60 V Common Mode Differential Probes are the ideal probes for lower voltage GaN power conversion measurement with the highest accuracy, best CMRR, and lowest noise.
-
product
Automotive Conveyor Control
Convey-O-Track
Computer Conversions Corporation
Computer Conversions' Convey-o-Trak Series are standalone precision Conveyor Drive Positioners, designed specifically for assembly-line applications. They serve as a reliable means of precisely positioning conveyors in a truly closed loop system that can be either: exactly job/product rate synchronized position (Line Setters), or, absolute position synchronized to any adjacent conveyor (Synchronizers).
-
product
Conversion Devices and Adapters
Conversion devices and adapters fulfill several roles. For example, you can use them to convert an output signal to a signal type that can be measured by a data logger, to adjust resistive bridge measurements, or to build distributed measurement networks.
-
product
Autocorrelator
Our autocorrelator is designed for those who do not require the sophisticated pulse characterization provided by our FROG Scan systems. Mesa Photonics' autocorrelators are built around the same advanced servo motor used in our FROG Scan systems and can be upgraded later to a complete FROG Scan or FROG Scan Ultra by purchasing a conversion kit. The servo motor precision corresponds to 1 fs temporal steps.
-
product
Large-size Hybrid Reverberation / Anechoic Chamber
F-Series
The F large-size hybrid Reverberation/Anechoic Chamber represents the most versatile OTA test system in the market today. With the same unique test features of their E Series RC counterparts, the F-Series can also test large form-factor devices under test (DUTs) like laptops, large TV sets, solar and trash compactors, drones, fridges or washing and vending machines, among others. With up to 16x16, 8DLCC and DUTs up to 2m and 500 kg including full-body phantoms in a turntable, the F Series also expands the frequency range down to cover 200 MHz up to 40 GHz frequency ranges and the test modes to include EMC, BS, small cell, eNodeB and Virtual Drive Testing over the air (VDT-OTA). In an again unheard-of feature, the F-Series is also reverse-convertible into an Anechoic chamber, allowing Far Field (FF) and Spherical Near Field (SNF) radiation patterns, efficiency and gain measurements and pre-5G testing of antennas and devices. Conversion from RC to AC or vice versa can be performed within half a day.
