Pre-amplifiers
Detect and strengthen a signal prior to greater amplification.
-
Product
External Pre-amplifiers
-
Although all Spectrum A/D cards have a very powerful input section with a highly configurable input amplifier and a variety of input ranges it is sometimes necessary to have additional external amplifiers if the signal to acquire has an extremely low level. Spectrum offers a range of perfectly matching external amplifiers to cover such cases. These powerful amplifiers have been rated using the Spectrum cards and offer best performance together with high amplification rates.The amplifiers are simply connected between the signal source and the Spectrum A/D card input and can be manually switched between different settings using small lever keys. All amplifiers allow the offset compensation by using an adjustable screw.
-
Product
Precision Current Preamplifier
SIM918
-
Stanford Research Systems, Inc.
The SIM918 Current Preamplifier is ideal in applications in which the input offset voltage must be kept to a minimum. The DC voltage difference between the two inputs (current input and voltage bias) is accurately measured every 2 seconds, and is nulled.
-
Product
Hydrophone
TC4047
-
The TC4047 miniature hydrophone offers a useable frequency range from 1kHz to 170kHz. The hydrophone incorporates a high quality 20dB low-noise pre-amplifi er which provides optimal conditions for signal transmission. The high sensitivity provides excellent signal to noise ratio and immunity against induced cable noise. The hydrophone is omnidirectional up-to 100kHz and has uniform receiving characteristic from 1kHz to 100kHz. An insert calibration circuit enables remote testing of the hydrophone condition. The hydrophone comes with a SEACON connector. The sensor element is permanently encapsulated in Special formulated NBR to ensure long term reliability. The rubber has been specially compounded to ensure acoustic impedance close to that of water. The strainrelief and outer jacket of the cable is made of high density polyurethane. TC4047 can be used in sea or fresh water.
-
Product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783124-01
Signal Module
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
Product
Sound Level Meter
831-LOWN
-
Easily make low noise measurements to 6.5 dB A-weighted using the Model 831-LOWN sound level meter paired with the 378A04 low noise microphone and preamplifier. Due to the innovative design of the 378A04 which uses a prepolarized microphone and ICP (constant current) interface, the combination produces a highly portable system that is battery powered and intuitive to use for measuring low noise levels.
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 3.6 GHz
N8973B
-
The N8973B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8973B.
-
Product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783156-01
Signal Module
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
Product
(40×70×12mm) Single Channel Small Form Factor Gain Block Pre-Amplifier EDFA Module
SPA4300-GM01
-
Hangzhou Huatai Optic Tech. Co., Ltd.
SPA4300-GM01 is a single channel Gain Block Pre-Amplifier EDFA module , adopts subminiature 40×70×12mm compact package, combined with artistic package and best optic performance, creating the best flexible and variable low-cost amplifier in the market. This module is suitable for multiple network application, especially the application that requires 40GB/S transmission speed.
-
Product
Microphone Calibration Workstation
9350C
-
The Precision Acoustic Calibration Workstation Model 9350C is an accurate, turnkey, automated PC-based system that features cost-effective calibration of ¼", ½" and 1" microphone cartridges (open-circuit sensitivity), microphone cartridges with preamplifiers (closed-circuit sensitivity) and microphone Frequency Response Function.
-
Product
Instrumentation
-
Unholtz-Dickie designs and manufactures a variety of transducer signal conditioners, accelerometers, remote charge preamplifiers, vibration monitors & limiters, transducer testers, buffer amplifiers and other special purpose instrumentation accessories for vibration testing.
-
Product
Amplifiers
-
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik GmbH offers a large portfolio of high performance broadband RF amplifiers. Optimized for linearity, high dynamic range and low noise, they cover all widely used radio standards like cellular, satellite radio, TETRA/BOS, GNSS, GPS, 802.11, including the new bands for LTE-U. They amplify wideband radio signals from shortwave over UHF, VHF up to 18 GHz in 50 Ohm technology (I-band, G-band, P-band, L-band, S-band, C-band and X-band). They are used as compact RF drivers, antenna pre-amplifiers or RF boosters in a variety of applications ranging from tunnel radio coverage extension, over airspace radio monitoring to in-ear monitoring and can also be offered as 1U 19” rack variants. Due to their advanced design, the power consumption is significant lower than typical industry alternatives, saving cost at customers with respect to cooling.
-
Product
Broadband Amplifiers
-
Blonder Tongue Laboratories, Inc.
Blonder Tongue offers a variety of RF amplifiers for broadband CATV or OTA (over-the-air) applications. Be it a 1GHz power doubling two-way indoor distribution amplifier or a mast-mounted preamplifier, or anything in between, we have you covered.
-
Product
Low Noise Voltage Preamplifier
1201
-
The Model 1201 Voltage Preamplifier with Remote Gain Programming Option (06) is usable in both computer controlled and maual applications requiring uncompromising performance.
-
Product
Acoustic Emission Preamplifier
-
The Acoustic Emission Preamplifier is a instrument designed specifically for use with acoustic emission sensors, which is used to boost the signals and filter out any noise or interference. With its advanced technical features and robust design, the QingCheng Acoustic Emission Preamplifier is the perfect choice for professionals seeking a high-performance acoustic testing solution.
-
Product
Microphone Preamplifier
426A30
-
1/2-inch preamplifier with 7-pin LEMO connector (for externally polarized microphones)
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 26.5 GHz
N8975B
-
The N8975B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8975B.
-
Product
Energy Probes
RjP-400 Series
-
The RkP-400 Series probes consist of a compact detector assembly, or head, and a preamplifier housed in a separate enclosure. The external dimensions of all the 400 Series Probes are the same, with identical detector planes, allowing for easy interchange of probes in an experiment. The heads have both ¼-20 and M6 tapped holes, a built-in 1" (25mm) filter holder, and a side-mounted BNC connector. Probe specific data, including spectral response curves and calibration dates, is stored in the preamplifier for access by the instruments.
-
Product
Electronic Instruments
-
The ORTEC range of modular electronics includes instruments in NIM formats as well as other modular instruments, such as photomultiplier bases, preamplifiers and other accessories. ORTEC also offers modular instruments for pulse height spectroscopy, fast timing, counting, high voltage power supplies and other special functions.
-
Product
ICP Microphone System
378A14
-
This model includes a 1/4" microphone cartridge, a mated preamplifier with TEDS, and system calibration.
-
Product
Low Cost Microwave Wideband APD Preamp Receivers
MR11 (40KHz~18GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MR11 series microwave wideband optical receiver, adopts high Sensitivity APD diode and Low Noise Preamplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s high speed communication system.
-
Product
Preamplifiers
-
A.H. Systems'' Preamplifier line is an excellent choice with a rugged design, no hassles with soldering your own power leads and they improve overall system sensitivity by at least 20 dB. All of A.H. Systems'' Preamplifiers come with a 12-volt (or 15-volt) DC regulated power source. A low voltage indicator confidently allows you to power the amplifier with your own external 12-volt DC battery. This makes it a convenient choice for field measurements. See table below for amplifier specifications.
-
Product
1 MHz Bandwidth Voltage Preamplifier with Bandpass Filter
EC6081 mk2 - preamplifier
-
The EC6081 mk2 (VP2000) is a 1MHz bandwidth voltage preamplifier with bandpass filter that is designed for uses in conjunction with piezoelectric hydrophones. VP2000 offers excellent low-noise performance over the entire frequency range; and adjustable gain selection. A range of 12 high-pass and 12 low-pass filters are available, these allow ideal band pass filter settings.
-
Product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Test Instrument
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
Product
OEM Pulse Energy and Power Measuring Instrument
LEM 2510
-
This OEM-Meter is assembled in a standard cassette for the industrial 19? system. It has a width of 21TE. A touch panel and function keys make this device comfortable and easy to handle. The preamplifiers integrated into the device and the choice of sensor sensitivity, allow to use a wide range of sensor heads.?
-
Product
Probes For Non-Contact Ultrasonic Testing
SONOSCAN CFC / CF
-
Due to the strong damping properties of air, low frequencies in the kHz range are used in air-coupled ultrasonic testing. It is therefore all the more important that the ultrasonic transducers offer a particularly high sensitivity in order to ensure high penetration and improved resolution. We achieve this, among other things, by installing preamplifiers in the receiver probe as well as by using our own Piezocomposite Technology, which enables a flexible use of the matching materials in our CFC and CF probes.
-
Product
Transducers
-
CRYSOUND offers an impressive array of sensor products, including measurement microphones, preamplifiers, artificial ear coupling cavities, and artificial mouth sound sources. These diverse products enable us to meet the specific needs of our clients with precision and innovation.
-
Product
C-Band DWDM Pre-Amplifier EDFA (WPA-C)
HWA4300 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4300 series, is designed for C-Band 44 waves or 88 waves DWDM system design Pre-Amplifier gain flatness. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, Low noise, excellent gain flatness characteristics and transient characteristics.
-
Product
Preamplifier, 10 MHz to 4 GHz
87405B
Amplifier
Preamplifiers and System Noise Figure Application Note This note discusses noise figure basics including applications and characteristics of Keysight simplifier technology. Highlighted are Keysight's 87405C portable preamplifiers that provide an exceptional gain of 25 dB up to 18 GHz and a probe-power bias connection which eliminates the need for an additional DC power supply. Read the Preamplifiers and System Noise Figure Application Note now!
-
Product
Low Noise Amplifiers for Radio Amateurs
-
Our Low Noise Preamplifiers are remarkable for extremely low noise, excellent SWR, high efficiency and a high IP3. The Low Noise amplifiers are especially selective and absolute stable therefore oscillation is avoided. Even if you have a bad SWR. This is the reason why radio amateurs and club-stations all around the world trust in Kuhne electronic equipment. The products are perfect for use in contests, EME, MeteorScatter, Aurora and Tropo DX. Small mechanical measurements and technical innovations from the professional sector, e. g. milled aluminium cases, enable high temperature stability and tower mounting. Numerous contest victories, records and first contacts with a country were and are achieved with Kuhne products. Don't compromise and get technology from Kuhne electronic!
-
Product
Current Sensors
-
Our current sensors were designed for a simple, customer-specific construction of niobium wire wound magnetometers, gradiometers or preamplifiers for small current or voltage signals.
