CAT 6
Category 6 cable.
-
Product
Voltage Rectifier
-
A voltage rectifier, designed and manufactured by Monex GeoScope Pty. Ltd., has been added to the terraTEM suite of products. The voltage rectifier has been designed to provide 6 kW, 120 V, 50 A output and is the ideal rectifier to guarantee the necessary stable, ripple free current for the full range of Monex GeoScope’s transmitters. This includes the internal transmitters for the terraTEM24 (50 A, 120V), terraTEM (15 A, 24 V) and the terraTX-50 external transmitter (50 A, 250 V). In addition, the voltage rectifier outputs a clean, filtered 24 V suitable for powering either the terraTEM24 console or terraTX-50 console electronics. And the output stability of the voltage rectifier is not disturbed by the fast turn-off times available on the Monex GeoScope transmitters.
-
Product
Protection Relay Tester
PW866i
-
PW866i (6×32A, 4×300V) Protection Relay Tester could be used for testing all kinds of relays, also supports testing IEC 61850 combined relays. Its local control system is with 10.4inch LCD screen based on Windows system.
-
Product
Coaxial Attenuators Set
11581A
Attenuator
The Keysight 11581A contains a set of four Keysight 8491A attenuators 3, 6, 10 and 20 dB with type-N connectors, furnished in a walnut accessory case. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
Product
COLOCOIL® AM Isocoupler
-
LBA’s modular approach allows the operator to start with one CoLoCoil®, and build out to 6, 9, or more – supporting 50 or more antennas! Practically "plug and play", expansions are fast, minimize AM station impact, and maintain full grounding and lightning protection!
-
Product
Protective Relay Test Set
POM2-6143
-
POM2 series protective relay test equipment is the best modular designed relay tester with local control system. There are 2 models, the POM2-6143 and POM2-3243, the POM2-6143 with 6×15A and 4×300V.
-
Product
PCI Board
FastX1703-DIG
-
The FastX1703-DIG is a raw-length PCI board with two input connectors. Each connector supports 16 data bits, 10 general purpose inputs, and 6 general purpose outputs. Clock rates up to 166 MHz can be supported. All the inputs and outputs are connected to an FPGA on the board are essentially available for any purpose required by the interface. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, zero to four Nexperia PNX1702 VLIW processors before output. Finally, the Fast-X-DIG interfaces to the host computer through a 4 x PCIe interface for state-of-the-art data acquisition.
-
Product
Dissolution Tester Accessories
-
Teledyne Hanson's diverse range of dissolution tester accessories significantly expands the functionality of their instruments, catering to various applications such as small volume testing, Chinese small volume testing, semisolids testing, and immersion cell usage per USP <1724>. The lineup includes:- Precision dissolution vessels- Vessel covers- Paddles (USP Apparatus 2)- Baskets (USP Apparatus 1)- Paddle over disk “transdermal sandwich (USP Apparatus 5)- Rotating cylinder (USP Apparatus 6) - Sampling probes- Small volume kits- Filter block kits- Humidity-sealed dosage-drop chambers- Stationary basket and cover
-
Product
Parrot Test Leads
-
2x Test Leads ( 600V Cat II, 10 A ) with 1m Silicone Cable with Banana plug.
-
Product
Time Domain Reflectometer
BAUR TDR 510
-
Handheld Time Domain Reflectometer TDR 510. The BAUR handheld time domain reflectometer TDR 510 is used for fault location in all metal cables such as power cables, coaxial cables, data cables and communication cables. The BAUR TDR 510 comes with a device storage for 50 measurements and the option to compare the trace of an active TDR measurement with a stored trace.* Configurable for various measurement ranges and cable types* Standard-compliant, safe measurements on live cables through the measurement category CAT IV / 600 V* Ideal for fault location in the area of telecommunication, video technology, data and security technology
-
Product
ATCA 6.5 Slot System
-
6 slot custom system leveraging essential features of AdvancedTCA® to meet needs of industrial control application.
-
Product
Front Panels For Plug-In-Units | VPX
Front-Panel-Plug-In-VPX
-
EMC front panel for VPX plug-in-units | 3 and 6 U
-
Product
PXI 6-Channel 10A Solid State SPST Switch
40-182-011
Switch Module
The 40-182-011 has 6 off high current SPST switches in two PXI slots and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
Coil Analyzers & Power Supplies
-
Coil analyzers and power supply units are portable and lightweight devices intended for use in harsh switchyard and industrial environments. The typical application is switchgear and circuit breaker testing when substation battery is not connected or available. An advantage over substation battery is enabled testing in under-voltage and over-voltage conditions. Furthermore, the stable voltage outputs with a very low ripple (<0,5%) enable an analysis of the coil and motor current graphs recorded with circuit breaker analyzers from different vendors.SAT40AD, POB30AD, and POB40AD are unique devices in the market due to their dual purpose:Power supply for coils and spring-charging motorsTesting circuit breaker’s coils, motor, and auxiliary circuitAll DV Power coil analyzers and power supply units have four separate outputs for opening and closing coils.SAT40AD has two powerful motor outputs (AC and DC) which can withstand up to 40 A inrush current.POB30AD and POB40AD have DC motor output rated up to 30 A and 40 A respectively. With the use of motor outputs, POB and SAT can also be used as a power source or a temporary battery charger.SAT40A II series instruments can be controlled via PC. The DV-Win application software is used to control both SAT and CAT (Circuit Breaker Analyzers & Timers) devices at the same time, making a unique test system for switchgear and circuit breaker testing.
-
Product
LXI Microwave Multiplexer, SP6T, 3-Bank, 26.5GHz, 50Ω, SMA
60-800-303
Multiplexer Module
Our 60-800-303 is a 3 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXIe-5785, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver
785584-01
FlexRIO IF Transceiver
12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver—The PXIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PXIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
Product
Collapsible 6 Inch Charge Plate Monitor Assembly
CPM-760A
-
- 6" x 6" (15 cm x 15 cm) conductive plate- Total system capacitance of 20 pF ± 2 pF- Meets the requirements of ANSI/ESD STM3.1 and ANSI/ESD SP3.3- Designed to perform audits on overhead ionizers and room ionization systems- Flexible to also evaluate and balance bench top ionizers- Completely collapsible for compact storage- Designed to be used with the PFM-711A and PFM-711B
-
Product
Computer-On-Module
CM22301
-
LinkedHope Intelligent Technologies Co.,Ltd.
CM22301 uses Intel® sixth-generation Skylake platform and Core M low-power SoC processors, and integrates the full functions of CPU, GPU and South/North Bridge on a single chip. The processor provides powerful computing and display performance with dual-core and four threads configuration. Its turbo frequency can boost up to 3.1GHz and the display output resolution can be up to 4K. CM22301 has an amazing thermal design power consumption of only 4.5W (TDP) and can be used for a variety of high-performance fanless designs. CM22301 supports up to 16GB dual-channel low-voltage DDR3L memory populated onboard, and up to 64GB on-board solid state disk silicon, as benefit the development of ruggedized products for harsh environment applications.As defined by VITA 59 specification, CM22301 provides up to 6 PCIe lanes, enabling flexible functionality expansions, such as NICs, DAQs, video capture and so on. Meanwhile, CM22301 also provides up to date computer interfaces like GbE, SATA3, USB3.0/2.0, HD Audio, etc. CM22301 uses the same 220pin board-to-board connector and Type10 pin out definition as COM Express.
-
Product
MR50 THT Vertical | 10, 12, 16 Positions | 1, 2, 4 Poles
MR50-Overview
-
Highly robust Ø 1/2" selector with 22.5°, 30° or 36° indexing angle, up to 6 Ncm switching torque and operating temperature from -45 to 85° C
-
Product
Cable Certifiers
LANTEK III Series
-
New permanent link adapter saves money. Send test data anywhere using IDEAL AnyWARE app. Certifies multimode and single-mode fibre (optional). Professional PDF reports with free software. Certifies twisted pair cabling to TIA/ISO standards. The LanTEK III is an easy to use cable certifier that meets existing TIA and ISO/IEC performance requirements for testing up to Cat 7A/1000MHz. FiberTEK III adapters are used with LanTEK III for fast and simple certification of high bandwidth single-mode and multimode fiber optic cabling including support for encircled flux testing.
-
Product
Ratemeter
TR400
-
Full-logic control process ratemeter displays speed and direction of rotating equipment.• Displays rate or time-in-process• Detects and converts 0.01 to 4,000 Hz signal input• Optional relay outputs: 2 or 6• Optional analog output: 4-20 mA or 0-10 V• Completely field programmable• Full diagnostic functions• Single-channel or bi-directional (quadrature) decoding• Front panel reverse direction indication• 3 programmable inputs• Built-in relay test function
-
Product
LXI 50Ω 6:1 Microwave Multiplexer 4-bank 18GHz SMA
60-800-004
Multiplexer Module
High performance RF multiplexer suitable for switching microwave signals
-
Product
High voltage Flexible range Regulated DC Power Supplies
PSF-H Series
-
* Main Applications: High-voltage capacitors or relays used for hybrid cars, electric cars, solar power system and high-voltage LED lighting equipment.* 6 times of flexible output range: PSF-800H covers output for several units of conventional type regulated power supplies within 800W ( max voltage 800V, max current 6A. ).* Constant Power Control: CP mode is available in addition to CV and CC modes.* Changeable setting style: Vertical or horizontal setting by 90rotating panel.* Sequence Operation: Stand-alone sequence is available with the insidememory programmed by PC, through the optional control board (IF-60GP, IF-60RU).* Master-slave parallel operation: Possible to increase the output current by master-slave parallel connection of the same model (up to 2 units).* Various functions are available: Output OFF timer, 3-point preset memory, Remote sensing, External analog control, OVP/OCP/OHP protections
-
Product
FS1 FUSE
FS1MAFUSE
-
*0.63A/500V AC IR50kA (6 x 32mm) fuse for MD251 and MD257 digital multimeters
-
Product
AMD Ryzen™ Embedded V2000 Processor
AIMB-229
-
High perf. Zen CPU 8 cores / 16 threads & 64GB DDR4 SODIMMAMD Radeon Graphics core with up to 7 compute units and Quad 4K display supportSupports 8 x PCIe , 2 x M.2 expansion slots, 6 x COM, 2 x USB 2.0, 6 x USB 3.1 connectorsSupports 12 voltage DC-In or 4-pin ATX power inputSupport Windows 10 LTSC & Ubuntu 20.04 LTS; SUSI API and WISE-DeviceOn
-
Product
Protective Relay Testing Equipment
PW466i
-
PW466i (6×20A, 6×150V) 6-phase relay tester is a powerful secondary injection protective relay testing kit with 6-currents and 6-voltages sources.
-
Product
Temperature Transmitter
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitters for platinum temperature sensors and thermocouples in 6 mm housing with calibrated range selection. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
Product
UV Light Meter
Model 308T
-
Built for high intensity applications the NEW OAI Model 308T UV Light Meter is a dependable, direct-reading instrument designed for measuring UV light intensity for UV curing. The Model 308T features detachable probes for use in the UVA, UVB and UVC ranges, plus a high speed serial port. Accuracy of the meter is within ±3%and measurement repeatability is within ±3 LSB (least significant bit). Like all OAI precision instruments, the Model 308T provides NIST traceable measurements. This easy-to-use meter is auto-ranging from 0.1 to 1999.9 milliwatts/cm2 full scale when used with the 2000 milliwatts/ cm2 probe. The linearity of the meter in this range is at least ±(.002% + 6 LSB).
-
Product
6-way Round Pin Vehicle side Circuit Tester
7897
-
Innovative Products of America
The 6-way Round Pin Trailer Circuit Tester tests trailer circuits on older light to medium duty trucks and RVs. Plug the 6 pole trailer tester into the back of the vehicle and apply the Brake Lights, Turn Signals, Running Lights etc.
-
Product
9th Gen Intel® Xeon®, Core™ i7/i5/i3-Based Compact Industrial GPU Workstation
DLAP-8000 Series
-
- 9th Gen Intel® Xeon®, Core™ i7/i3 LGA processors with workstation C246 chipset- Dual SODIMMs for up to 64GB DDR4 / ECC options*- Rich I/O: 2x DP++, 1x DVI-I, 3x GbE, 4x COM, 8-ch DI, 8-ch DO, TPM 2.0- 2x USB 3.1 Gen2, 1x USB 3.1 Gen1, 3x USB 2.0- Up to 4 hot swappable 2.5" SATA 6 Gb/s tray with RAID 0/1/5/10 support, CFast, M.2 2280- Embedded expansion: 1x Mini PCIe, 1x M.2 3042, 2x USIM- Front accessible I/O and adaptive Function Module v.2 option- Flexible and powerful PCIe expansions via backplane
-
Product
NIST Calibration for D600A-AT.
D600A-AT-CCNIST
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
