Device Under Test
a specific purpose component or module check; ex. substantial component of a PCB.
See Also: DUT, Unit Under Test, EUT
-
Product
Automated Test Interface
ATI-100
-
Matrix Test Equipment Incorporated
Now, with our ?New? Model ATI-100 you can turn your existing Matrix Signal Generator and Switchable Filter Bank into a full-blown DTS (Distortion Test System). Plug and play is the word, just plug in your Multiple Frequency Signal Generator, Switchable Filter Bank, Spectrum Analyzer, Oscilloscope, Power Meter, Frequency Counter, etc. to allow the following automatic testing with a single insertion of DUT (device under test
-
Product
Automatic Fixture Removal
S95007B
-
Many devices do not have coaxial connectors and so they are put in fixtures in order to measure them in a coaxial environment. You must accurately remove the effects of the fixture to get a good measurement of the device under test (DUT). This option adds a powerful application wizard to guide you through characterizing a fixture and removing it from the measurement. The S95007B software is compatible with M980xA PXI Vector Network Analyzers.
-
Product
PXIe-4154, 2-Channel, 8 V, 3 A PXI Programmable Power Supply
781155-01
-
2-Channel, 8 V, ±3 A PXI Programmable Power Supply—The PXIe‑4154 is a specialized programmable power supply for battery simulation. It is designed to simulate a lithium‑ion battery cell’s transient speed, output resistance, and 2‑quadrant operation (source/sink). Critical to many RF and wireless applications, the simulator’s fast transient response time allows it to rapidly respond to changes in load current with minimal voltage dip, which makes the PXIe‑4154 ideal for powering devices under test (DUTs) such as RF power amplifiers, cellular handsets, and a variety of other mobile devices. To model the behavior of a battery more accurately, you can use the onboard programmable output resistance to simulate a battery’s internal resistance. For quiescent and standby current measurements, the PXIe‑4154 features integrated current measurement.
-
Product
Electromechanical Transfer Switches up to 40 GHz
-
Fairview Microwave’s line of electromechanical relay transfer switches can be utilized for numerous applications to increase system level capabilities and can help simplify the overall design approach. With two input and two output ports, transfer switches can connect two different instruments with two devices under test. Additionally, they can be used as drop-out switches, for signal reversal or to bypass a component under test. These products are typically used in military communications and broadcast systems, SATCOM, test & measurement, instrumentation applications and are suitable for aircraft use.
-
Product
Functional Test
xUTS
-
Extend test to encompass copious test points and DUT varieties along with real-time, hardware-in-the-loop and other state-of-the-art instrumentation. extendedUTS (xUTS) is a custom product for high complexity functional test. Configured for the unique needs of a class of devices under test (DUTs), the xUTS employs our universal test system approach that combines the best open platform instrumentation and software along with mass interconnect technology.
-
Product
2-Axis Rate and Position Tables
-
When a device under test needs to be stimulated with simultaneous movements around two axes, then a product from the ACUTRONIC two-axis motion simulator range is the right choice. Due to their independent motion simulation in two axes they are very versatile: they are used as Inertial Guidance Test Systems (IGTS), for HardWare-In-the-Loop (HWIL) testing, for the test of optronic pointing devices, and many more applications.
-
Product
PXI Dual 18 Channel MUX, 96-Pin SCSI Connector
40-735-912-S1
-
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
Regenerative Power System, 1500 V, ±60 A, 30 KW, 400/480 VAC
RP7984A
-
The RP7984A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
Product
Regenerative Power System, 500 V, 20 A, 5 kW, 200/208 VAC
RP7951A
-
The RP7951A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test. The regenerative capability enables the energy normally consumed to be returned to the grid cleanly, saving costs associated with energy consumption and cooling.
-
Product
Regenerative Power System, 2000 V, ±30 A, 20 KW, 400/480 VAC
RP7973A
-
The RP7973A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
Product
PXI Single 10 Channel MUX, XLR Connectors
40-735-902-S2
-
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
Artificial Power Supply Network
KH3760
-
Beijing KeHuan Century EMC Technology Co,.LTD
The artificial power supply network (also called the power supply impedance stabilization network) should be able to provide a stable impedance to the device under test in the radio frequency range, isolate the device under test from high-frequency interference on the power grid, and then couple the interference voltage to the receiver.
-
Product
Plane Wave Converter
PWC200
-
The R&S®PWC200 Plane Wave Converter is a bidirectional array of 156 wideband Vivaldi antennas placed in the radiating near field of the device under test (DUT). The phased antenna array can form planar waves inside a specified quiet zone within the radiating near field of the 5G massive MIMO base station for realtime radiated power and transceiver measurements (EVM, ACLR, SEM, etc.).
-
Product
2kV, 400 MHz High Voltage Differential Probe
HVD3220
-
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
Product
NI-9229, ±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Module
780180-01
-
±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Module - The NI‑9229 performs differential analog input. The NI‑9229 is an effective general-purpose analog module because of its resolution, sample rate, and input range. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating.
-
Product
Water Brake Engine Dynamometers
Hydraulic Dynos
-
Ideal for a wide range of markets, water brake engine dynamometers churn water inside the housing and transfers energy by momentum exchange and water shear. The more water flowing through the dyno, the greater the braking force exerted on the device under test.
-
Product
Power Supplies And Loads
-
Power Supplies and Loads power devices under test (DUTs) such as RF power amplifiers and cellular handsets. The power supply takes in AC power and delivers DC voltage with a fixed polarity, either positive or negative, to its load.
-
Product
EMI Test Receiver
ESL
-
The R&S®ESL EMI test receiver combines two instruments in one, measuring EMC disturbances in accordance with the relevant standards and also serving as a full-featured spectrum analyzer for diverse lab applications. The combination of very good RF characteristics and all of the important functions needed for fast, precise measurement and evaluation of the EMC of a device under test in accordance with commercial standards is unmatched in this instrument class.
-
Product
Scienlab Measurement And Control Module
SL1064B
-
The Measurement & Control Module SL1064B is a rack-mount gateway for CAN- and LIN-buses with up to 6 channels. It can be used as a configurable communication interface between Scienlab Battery Test Systems and devices under test (especially their BMS) as well as additional components using CAN communication.
-
Product
Power Quality Analyzer
PQM-711
-
PQM-711 power quality analyzer is an advanced product for wide type of measurements, analysis and recording of network parameters 50/60 Hz and the power quality diagnostic according to European standard EN 50160. PQM-711 is an innovative model with a wireless communication Wi-Fi , which allows for automatic pairing with the included tablet, with a large 10" touch screen. Tablet allows full operating of the analyzer, live data preview and the reading and analysis of data stored in the internal memory. With this solution, the PQM-711 is an unique device that combines the advantages of the analyzer with built-in display and typical portable analyzers (known as Black Boxes).With the tablet you can very fast checked the device under test. On the other hand, you can leave the analyzer module for multi-measurements as a typical logger without display. You can very fast diagnose the machine under test using the tablet. On the other hand, you can leave the analyzer module itself for many days measurement as a typical logger without display. PQM-711 has a transient registration with a maximum sampling rate of 10 MHz (rapid changes in voltage) and control signals. The minimum duration of the registered transient is 650 ns.
-
Product
Spring Probes
-
An essential component in the testing of electronic components. In Test & Measurement applications, they are used to make contact with test points, connecting the DUT (device under test) with the test equipment.
-
Product
Automatic Calibration Module
ACM2509
-
ACM2509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full two-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to seven connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
Product
PXIe-4113, 2-Channel, 10 V, 6 A PXI Programmable Power Supply
782857-02
-
The PXIe‑4113 is a programmable DC power supply with isolated outputs. It helps simplify the task of designing automated test systems for a wide range of applications—from aerospace and defense to automotive and component test—by eliminating the need to mix multiple instrumentation form factors in a given test rack. It also has standard output disconnect functionality that allows isolation from the device under test (DUT) when not in use, and remote sense to correct for losses in system wiring.
-
Product
Vector Impedance Analyser
TE3000
-
The TE3000 Vector Impedance Analyser is a portable desktop instrument designed for high accuracy impedance measurement. The probe style construction and small output signal make it ideal for "in circuit" impedance characterisation of small signal devices without the risk of damage to the device under test. The TE3000 comes factory calibrated to the tip of the probe with optional custom calibration. Turn it on, set the frequency, take a measurement, and display the results in any format.
-
Product
1kV, 25 MHz High Voltage Differential Probe with Auto Zero Disconnect
HVD3102A
-
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
Product
Pogo Pin
-
Probe pin is also known as pogo pin or spring probe. It is designed to test the connection between two circuit boards and devices or equipment under test.
-
Product
PXI Matrix Switch Modules
-
PXI matrix switch modules deliver low, medium and high-density switching of multiple channels in a single instance. They are organized in rows and columns to provide maximum flexibility, allowing you to connect any row to any column, making them ideal for routing multiple signals between your device under test and your instruments.
-
Product
Accessory EFT/Burst generators IEC 61000-4-4
-
The field sources and the burst transformer are used to harden the device under test. They are powered by an EFT/burst generator.
-
Product
HandyScope HS6-DIFF With SafeGround & SureConnect: 500 MS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-500XMSG-W5
-
The only oscilloscope in the world that has:- SafeGround, differential input channels that can be switched to single ended.-SureConnect, auto-detects a true connection between the probe tip and the device under test.- CMI interface.- USB 3.0 interface, 5Gb/s data transfer- Lowest noise
-
Product
RFP DC Low Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
