Jumpers
-
Product
Connector Adapter
-
MCA-ST connector adapter for the connection of micro plugThe connector adapter allows the direct connection of fine-pole connectors on circuit carriers or jumpers. The adapter is guided over the connector housing, which overcomes the tolerances of carrier and mounting.
-
Product
Pin-Line™ Vertisocket™
Series 0517
-
Pin-Line Vertisockets. For mounting components, jumpers, etc., at right angle to PC board. Available 1 to 25 positions; cuttable to any number desired.
-
Product
9 Pin Breakout Interface
VSI-Breakout-9
-
The VSI-Breakout-9 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
ISA Data Acquisition Boards
A-823PGH/S
-
The A-823PGH/L is 12-bit multifunction analog and digital I/O boards for the PC/AT compatible computer. The A-823PGH/L offer 16 single-ended or 8 differential analog inputs, plus two channels of analog output with 12-bits resolution. In addition, The A-823PGH/PGL has 16 digital input, 16 digital output , and one timer/counter channel. The A-823PGH Provides gain of 0.5, 1, 5, 10, 50 ,100 , 500 , 1000 while the A-823PGL provides gains of 0.5 , 1 , 2 , 4, 8 . It has a maximum sampling rate of 125 k Sample/Sec., DMA operation is jumper selectable for levels 1 or 3. Interrupts are jumper selectable between 3 and 15.
-
Product
CPRI Interface Panel Kits for Connectivity Testing
-
RFS’ CPRI Interface Panels are used to test fiber connectivity between Optical Base Band Units (BBU) and Remote Radio Heads (RRH), allowing cell operations and system performance engineers to ensure the best performance without having to disconnect the fiber optical system or disrupt service. In addition, the CPRI panel enables easy RF over CPRI testing at the bottom of the tower, reducing the need for unnecessary tower climbs, thus minimizing maintenance cost and overall OPEX for customers. The RFS CPRI panel is bundled with RFS’ high-quality fiber optic jumpers, providing an end-to-end solution that includes HYBRIFLEX® fiber-to-the-antenna DC and F/O solutions.
-
Product
SparkFun Qwiic EEPROM Breakout
512Kbit
-
The SparkFun Qwiic EEPROM Breakout is a simple and cost effective option to add some extra storage space to any project. With 512 kilo-bits (or 64 kilo-bytes) of storage, this product is great for any microcontroller that doesn't have any EEPROM storage space, like the SAMD21. You can use the Qwiic EEPROM for storing data like GPS waypoints and other user settings that need to be maintained between sketch uploads. The SparkFun Qwiic EEPROM has three address jumpers, allowing for up to eight EEPROMs on one bus. All communication is enacted exclusively via I2C, utilizing our handy Qwiic system (as the name implies). However, we still have broken out 0.1" spaced pins in case you prefer to use a breadboard.
-
Product
Media Converter, 100Mbps, Multimode 1310nm, 2km, SC
EKI-2541M
-
Provides 1 x 10/100 Mbps Ethernet port with RJ45 connectorProvides 1 x 100 Mbps Multi-mode SC type fiber portProvides internal jumper for Link Fault Pass-through (LFP) settingSupports full/half duplex flow controlSupports store and forward transmissionSupports auto-negotiationSupports MDI/MDI-X auto crossoverSupports redundant 12-48 VDC power inputProvides flexible mounting: DIN-rail and Panel mount
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Carrier Card
VIPC627-ET
-
VIPC627-ET is a 6U VME carrier card with four IP slots and extended temperature range. Two 50-pin, 0.1 inch flat ribbon cable connectors mounted in the front panel provide access to all IP I/O lines. Also, all I/O lines of 'IP D' are routed to VME P2 and 14 user selectable I/O lines of 'IP C' can be routed to VME P2 via a jumper field.
-
Product
Junction Boxes
-
Junction boxes are used for complex power and signal distribution. The junction boxes have redundant mechanical barriers. The mechanical integrity of the junction box is verified during helium leak testing and hydrostatic testing of the jumper assembly. Thermal and pressure compensation is provided by the radially compliant hose or by purpose built bladder compensators, hose lengths must be sized according to the junction box internal dead volume.
-
Product
Passive Devices
-
Fiber Splitters, Muxes, CWDM, DWDM, WDM, PON, Fiber Jumpers, Fiber Attenuators.
-
Product
Jumper Cables For Multiport Configuration Of M937xA PXI VNA
Y1242A
-
Use Keysight Y1242A Jumper Cables for multiport configuration of the M937xA PXI Vector Network Analyzer (VNA).
-
Product
Switch Modules - 16 Single or Two Pole Relays Arranged as Four Separate 4x1 Multiplexers
JX16/4(4x1)-1 and -2
Switch Module
This module has 16 single or two pole relays arranged as four separate4x1 multiplexers as shown in the figure. The muxes may be operated and wired individually for up to 64 4x1"s per chassis, or jumpered together to form 8x1"s or 16x1"s or jumpered to the backplane to form up to a 256x1 mux or two 128x1 muxes. It is available with Type S, M or LT reed relays.
-
Product
High Density 1xN mux or 2xN Matrix Switching Systems
JX Series
-
This compact and economically priced series can be used as either 1xN multiplexers, 2xN matrices, or individual switches. As multiplexers, they can be used as a large number of individual muxes or jumpered together to form as large a mux as you need to switch a large number of inputs or outputs to one common port. As a 2xN matrix they allow you to switch any number of signals between two ports of a DVM, DMM, LCR, or other type of meter or supply. Individual relay modules are available for other configurations requiring discrete SPST or SPDT relays with standard or power relays.
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Relay Test Jumper Kit
56810
-
Set includes four jumpers to fit the most popular size relays on domestic and import vehicles. Simply remove relay to be tested, insert correct jumper and insert relay into jumper. When using green four pin jumper be careful to align pins on jumper and relay correctly. No need to pierce wires or connect multiple jumper wires. Jumpers have tabs for clamping and flat pads to place test leads on. Set comes in blow-molded case for storage.
-
Product
PXI Dual 0-30VDC Programmable Power Supply
TE3200
-
The TE3200 is a dual output programmable DC power supply designed for use in PXI/CompactPCI chassis. The TE3200 occupies a single slot and will utilize an external supply of 48VDC (provided). A separate srrew-terminal/power adapter board, p/n TE3202, provides connectivity for two 48VDC power suppies and screw-terminals and jumpers for voltage and sense selection and connection. The TE3202 is included with all retail purchases (not included with OEM purchases).
-
Product
Optical Extended CAN Bus Jumper
EOFL-C
-
Optical Extended CAN Bus Jumper, using fault tolerant to optical conversion to extend the range, can extend up to 5 kilometers subsea.Qualified repeater housing protected on each side by highly reliable glass to metal sealed penetrators.
-
Product
Flat Pin-Staked Flex Jumpers
Series 171 thru 173
-
Flat Pin Staked Flex Jumpers. Aries Flat Pin Staked Flex Jumpers combine thin, flexible, solid Copper conductors embedded between layers of tough, flexible, flame- retardant insulation.
-
Product
Load Monitoring Units (LMUs)
-
Magtrol's Load Monitoring Units are used for measuring load, force and weight from signals generated by strain gauge transducers. Specifically designed for use with Magtrol's Load Measuring Pins and Load-Force-Weight Sensors, the LMU Series provides excitation voltage while conditioning the bridge output signal. Each unit contains DIP-switches and jumpers for greater flexibility and complete adaptability
-
Product
ArgoBot Kit
ROB-00001
-
The ArgoBot Full Kit is a fully assembled robot and controls development platform. It is based on the Digilent chipKIT WF32(TM), a WiFi enabled development platform, and configured for LabVIEW targeting. Most importantly ArgoBot was designed with FIRST Robotics Competition teams in the front of our minds! Named after the FRC Team 1756 mascot, Argos, the ArgoBot development platform includes a fully-assembled, ready to drive mini WiFi enabled robot (about 8" x 5" x 4"), as well as tons of FRC controls tutorials and example code (LabVIEW VIs). Features included on the ArgoBot will look very familiar to anyone who has worked with National Instruments products (Compact RIO and RoboRIO) in the past. This includes three 5V Digital I/O modules (with jumpered pull-ups), three 5V analog inputs, and an I2C header. Example VIs have been streamlined to enable a 1-click configuration style to accelerate your development process. We also added a 2-channel motor driver that is used to supply the ArgoBot drive motors. Our ultimate goal is that everything you can build, control or implement on ArgoBot can be easily leveraged on your FRC bot! Complimenting its many electrical features, ArgoBot is easy to work with and easy to maintain. The chassis is a polycarbonate (the extremely tough stuff that is easy to drill and modify but easily takes bumps and bruises without cracking) case that is fully intact - meaning that ArgoBot doesn't just come with a case... it is a case! Clean-up and organization is simple - just close the case and turn off the power switch.
-
Product
Modbus or Laurel ASCII ProtocolSerial Output DIN Rail Transmitters
-
Laureate TM Series serial output transmitters can be jumpered for two signal levels: RS232 or RS485. Two serial protocols are selectable in software: Modbus or Laurel's Custom ASCII.Modbus protocol operation is fully compliant with the Modbus Over Serial Line Specification V1.0 (2002) for 2-wire, half-duplex connection.
-
Product
CPCI or PXI Digital IO Board
MS 1802
-
*Bus Interface - PCI Bus*Number of Channels 198*Compatibility - TTL*Power on state - Inputs (high-Z), pulled up or down (jumper selectable)*Handshaking - Input, Output, or bi-directional*Data transfers - Interrupts, programmed I/O*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Fusion Bonded Cable Jumpers
Series 152FB
-
Fusion Bonded Cable Jumpers. Aries Series 152FB Fusion Bonded Cable Jumpers are flexible...plug them directly into PC boards or sockets. Stranded wire conductors are fusion bonded with an overcoat of tin for easy soldering or socketing. Each jumper is shipped with protective tabs on both ends for maintaining proper conductor spacing.
-
Product
DIP-ER™ Logic Jumper
Series 115, 116, & 117
-
DIP-ER Logic Jumper. Reliable, electronically tested solder connections. Protective covers are ultrasonically welded on and provide strain relief for cables. DIP-ER Logic jumper wiring is point to point. Consult factory for other wiring needs.
-
Product
8 Channel Sample & Hold and Signal Conditioning Board for Group3
-
All channels provide for voltage division ahead of transient suppression before going into the S&H ICs. Channels that are sampled and held use a common sample and hold pulse that samples while high and holds while low. Jumpers on each S&H chip allow buffering of analog signals where sample and holds are not required. An advantage to the buffers is that it provides a high input impedance for high impedance voltage dividers.
-
Product
Test Clips
-
Angled Nose allows tight hold on 66 blockUse on 110 block with jumper and bed of nailsUse on larger cables with single piercing nail
-
Product
PCI to PC/104+ Bus Adapter
327/328
-
Model 327 and 328 are bus-to-bus adapters that allow operating a PCI board from a PC/104+ card stack. They allow selection of important PC/104+ signals using jumper plugs, thereby avoiding the requirement of using hardwired settings. Model 327 aligns the PCI board parallel to the PC/104+ boards, while model 328 places it perpendicular.
-
Product
25 Pin Breakout Interface
VSI-Breakout-25
-
The VSI-Breakout-25 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Male/Female DIP Jumpers
Series 200 thru 216
-
Male/Femaie DIP Jumpers. Reliable, electronically tested solder connections. Protective covers are ultrasonically welded on and provide strain relief for cables. 10-color cable allows for easy identification and tracing.
